ZapWizard's Leatherman Free P4 Mods
-
Amazing job ZW!

Hey LM, see what you can do with the p series
That’s what we want, darn it 
Now even I consider buying a P4...once the price drops :D
-


The bronze steel part arrived. This is Rev 2 (And the version anyone who ordered is getting). This one requires less reaming out, and no hammering like you see in the video. The magnets also has a closer to the bit for a better hold on the bit.
-
Looks excellent
Great work Zap

-
Just an FYI for folks who purchased the bit holder:
The magnets are now looser inside, so they can fall back towards the hinge, and stick there. Making the bit holding power weaker.
I had to take mine apart and apply some super-glue and push the magnets back to their position behind the bit. -
@ZapWizard said:
Just an FYI for folks who purchased the bit holder:
The magnets are now looser inside, so they can fall back towards the hinge, and stick there. Making the bit holding power weaker.
I had to take mine apart and apply some super-glue and push the magnets back to their position behind the bit.Doesn't seem like major issue but good info.
Sent from my ONEPLUS A6013 using Tapatalk
-
@Happy Gilmore said:
Doesn't seem like major issue but good info.Sent from my ONEPLUS A6013 using Tapatalk

-
Got my thumb tabs and holster. Very nice. I got the small holster and it works good, but it's pretty snug on my belt. I was paying more attention to the belt width more than the thickness. Very usable, but might buy another one with a clip. I'll probably get an Extra large and fix a top mount clip. I'll use my current one with one of my thinner gun belts. Also, the thumb tabs work very well. The straight blade has always been a little difficult to deploy, but now it's a breeze. Very well done!!

-
Love it, any chance of a horizontal holster version? I can't stand how the perpendicular holsters dig in when I sit down. This is one of the biggest reasons I don't holster carry a MT.
Sent from my ONEPLUS A6013 using Tapatalk
-
@Slygrin said:
Got my thumb taps and holster. Very nice. I got the small holster and it works good, but it's pretty snug on my belt.Hey! That looks great. Belt sizes are a very tricky things. I had to just settle on a few military/government standards and hope from there.
@Happy Gilmore said:
Love it, any chance of a horizontal holster version?So this has been requested a few times on both the FREE and other holsters. So far I have just told people to purchase the TekLok version which allows for 45 degree and horizontal carry. (But with the added bulk of the TekLok clip).
It's not as straightforward as just hanging like normal. It is much harder to design a 90 degree carry unless it is very specific to your belt size. Making to too wide can make it so the tool tugs on your sideways, as the center of gravity isn't below your belt.
I could try designing a lower profile 90 degree carry. Something that doesn't hang down three inches, but perhaps down enough to keep the center of gravity below the middle of the belt.
And finally the other thing I can think of is that the tool is straight, you belt would have a small amount of curve. So any 90 degree carry would have to try to allow for that. -
Added bonus with the thumb tabs. I can easily deploy the straight blade and saw with my Left hand.
-
@ZapWizard said:
Hey! That looks great. Belt sizes are a very tricky things. I had to just settle on a few military/government standards and hope from there.So this has been requested a few times on both the FREE and other holsters. So far I have just told people to purchase the TekLok version which allows for 45 degree and horizontal carry. (But with the added bulk of the TekLok clip).
It's not as straightforward as just hanging like normal. It is much harder to design a 90 degree carry unless it is very specific to your belt size. Making to too wide can make it so the tool tugs on your sideways, as the center of gravity isn't below your belt.
I could try designing a lower profile 90 degree carry. Something that doesn't hang down three inches, but perhaps down enough to keep the center of gravity below the middle of the belt.
And finally the other thing I can think of is that the tool is straight, you belt would have a small amount of curve. So any 90 degree carry would have to try to allow for that.Awl good points. I'd say probably not worth time spent for a niche market. Been using the Readyman belt Sleave and am a little spoiled from how flush MTs sit in it.
Cheers,
HG -
My bit holder has been shipped! I have some 4mm bits coming too. I'm just wondering if anyone has any good ideas for carrying the bits? I have a small zipper case that I was planning on using, but curious what other options folks are using.
-
My P4 and P2 have finally arrived, deciding on which...
Thanks for the side view, I was wondering if I were to trim down the holster like this would it still work fine? (Assuming i always put the tool in locks downwards)
Secondly if I get the thumb tabs does it still fit in the holster blades inwards? (blades facing my body)

-
@aussieman said:
My P4 and P2 have finally arrived, deciding on which...Thanks for the side view, I was wondering if I were to trim down the holster like this would it still work fine? (Assuming i always put the tool in locks downwards)
Secondly if I get the thumb tabs does it still fit in the holster blades inwards? (blades facing my body)


Yes, the bottom locks would work fine with that portion removed. See the design above. Since this is for the metal clip, I also added a small ramp to the back that guides the belt into the clip opening.
If you like the design, I can upload it for ordering and provide you a special link to this model.Yes, the thumb-tabs work facing inwards on the FREE P4 holster, they were designed to fit together.
-
Ok I have tried to remain calm. But having a talented designer do customer specific mods is like being pampered in heaven.
Let’s do this. I’m ordering.
The very last thing I would ask is a side extension loop to clip a flashlight to. Is that asking too much?
I’m already ecstatic with the last post. You sir are a legend.
-
@aussieman said:
Ok I have tried to remain calm. But having a talented designer do customer specific mods is like being pampered in heaven.Let’s do this. I’m ordering.
The very last thing I would ask is a side extension loop to clip a flashlight to. Is that asking too much?
I’m already ecstatic with the last post. You sir are a legend.


To hold any flashlight well, I need measurements of the flashlight. A generic loop won't do.
I usually say no to added flashlight addons. The only one I have said yes to was for a customer who provided me very exacting measurements. (He hasn't said how well it worked yet)I also tried this for my own flashlight, and found I just liked it separately hung next to my multi-tool on its own loop.
When the two are combined I didn't like how the light offset the center of gravity. I even had a version at one point that had my flashlight on one side, and a Squirt P4 (wire strippers) on the other. It turned out to be very bulky. -
I defer to your expertise.
Let’s just order their amazing cut down version above. In black. Send me the link.
Bedtime in Oz,,;

-
@aussieman said:
Let’s just order their amazing cut down version above. In black. Send me the link.Here is the purchase page. I made it available to anyone who wants it.
(I believe store linking is allowed during July) -
Any chance you will be designing thumb tabs for the T2/T4?

(Sorry if this was asked before.)
-Wes.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login