ZapWizard's Leatherman Free P4 Mods
-
@Dutch_Tooler said:
Now THAT is another great idea... space may be an issue though... as I recall the older Surge T-shank holder/file/saw blade exchanger without the extra spring is 3.1 mm thick. One might get away with using the principle applied to the thinner ST300EOD T-shank holder. Where's my calipers?I just had an epifany. Rather than set it up to fit into the blade slot, why not make it fit in the middle like Zap's bit exchanger? You could reduce the thickness by the width of the file or awl and still be able to fit a two piece exchanger setup. Yes, you would have to carry the t shanks separately, but it would be worth it imo. That means theoretically u can use Zap's exchanger on one side for drivers, and on the other have a t shank exchanger that can fit Leatherman's surge file/saw kit + one thinner tool such as the awl. Having this other option would give ppl a different setup that could contain the original philips and flat drivers if wanted.
-
If you look at the scissors on the P4, they are shorter than they need to be. (Leatherman could have put in Surge sized scissors)
There is 12mm between the folded-in scissors, and the spacer on the pliers. That spacer is 3.0mm thick.
I was curious if some tool could be added to replace the spacer, my thought was a lanyard loop, but maybe a T-Shank holder could be squeezed in there, but 12mm may not be enough space. -
@ZapWizard said:
If you look at the scissors on the P4, they are shorter than they need to be. (Leatherman could have put in Surge sized scissors)There is 12mm between the folded-in scissors, and the spacer on the pliers. That spacer is 3.0mm thick.
I was curious if some tool could be added to replace the spacer, my thought was a lanyard loop, but maybe a T-Shank holder could be squeezed in there, but 12mm may not be enough space.12mm width is definitely too small unless you are some master engineering wizard
.....oh wait.

However, I would still consider a t-shank exchanger as part of the middle tools.
-
ZapWizard, very well done! I couldn't be happier. I can't wait to see what you do in the future.

-
Hey Zapwizard. Your work is amazing here.
A little suggestion since you are going ahead with the 4mm bits. Perhaps you could consider 3D printing a stack/sleeve/storage similar to the LM 2D bit holders to hold a row of 4mm bits? I think it's pretty sweet. -
Hey Zap, love the work here. I would be interested in a straight Leatherman bit driver (as someone who has invested in the set, not in 4mm bits) without the bottle opener, as every damn thing in the EDC world has one at this point. I'm thinking just a solid version of your first design. If you could make one, it would be the last thing to finally convince me to buy a P-series tool.
-
@Sam Lim said:
Hey Zapwizard. Your work is amazing here.
A little suggestion since you are going ahead with the 4mm bits. Perhaps you could consider 3D printing a stack/sleeve/storage similar to the LM 2D bit holders to hold a row of 4mm bits? I think it's pretty sweet.Hell yes! I would love to not carry 4mm bits in an Altoids tin
Btw I love how the driver and the blade
tabs are similar in color. -
@eymantia said:
Hey Zap, love the work here. I would be interested in a straight Leatherman bit driver (as someone who has invested in the set, not in 4mm bits) without the bottle opener, as every damn thing in the EDC world has one at this point. I'm thinking just a solid version of your first design. If you could make one, it would be the last thing to finally convince me to buy a P-series tool.He decided against it for good reason. By using 4mm bits he eliminates liability issues. The bottle opener is a "free" tool. Also the bottle opener can be used to grab standard 1/4 inch hex bits. Really clever function of it imo. Check the third page to see how the opener can hold standard hex bits.
-
@Happy Gilmore said:
He decided against it for good reason. By using 4mm bits he eliminates liability issues. The bottle opener is a "free" tool. Also the bottle opener can be used to grab standard 1/4 inch hex bits. Really clever function of it imo. Check the third page to see how the opener can hold standard hex bits.I’m aware of the function of the bottle opener, but it wasn’t exactly a “free tool.” IIRC it interferes with the ability to hold the bits properly.
Sent from my iPhone using Tapatalk
-
I have had at least a dozen requests for a Leatherman flat bit version. I think I can go ahead and make it now that I know the shrinkage amount and got the locking portion to work correctly. But alas I will be offline for most of this month, so it will have to wait until later.
-
@Happy Gilmore said:
He decided against it for good reason. By using 4mm bits he eliminates liability issues. The bottle opener is a "free" tool. Also the bottle opener can be used to grab standard 1/4 inch hex bits. Really clever function of it imo. Check the third page to see how the opener can hold standard hex bits.@ZapWizard said:
I have had at least a dozen requests for a Leatherman flat bit version. I think I can go ahead and make it now that I know the shrinkage amount and got the locking portion to work correctly. But alas I will be offline for most of this month, so it will have to wait until later.
See, better to let the man answer himself ;)
-
@ZapWizard said:
I have had at least a dozen requests for a Leatherman flat bit version. I think I can go ahead and make it now that I know the shrinkage amount and got the locking portion to work correctly. But alas I will be offline for most of this month, so it will have to wait until later.

-
Zap! Totally fantastic! Put me in for the LM flat version too!
-
Hmm, I think the flat version is going to need a stronger magnet and a barrier between the magnet and bits. Otherwise magnet is likely to crack. Zap probably already knows this I'm betting
-
I do like the magnet idea for the bit-driver. Leatherman uses only 2 types of bit holders a hinged version for the Skeletool and the regular one used on the other multitools. Neither one of those use a magnet.
-
Zap, do you think there is a way to make a t shank exchanger in the scissor slot? That would sell me on the P2 with both your add-ons right now.
-
I’d be in for the Leatherman version.
Sent from my iPhone using Tapatalk
-
Awesome work Zap!

Already ordered a holster for my Charge TTi (open clip version). Can not wait anymore

Thank you for your outstanding engineering performance
.Greetings from Austria
-
@Happy Gilmore said:
Zap, do you think there is a way to make a t shank exchanger in the scissor slot? That would sell me on the P2 with both your add-ons right now.I don't think I could do that with 3D printing, it would require both milling and sheet metal parts.
@Sidewinder said:
Already ordered a holster for my Charge TTi (open clip version). Can not wait anymore
Thank you for your outstanding engineering performance
.Thanks.
I am going to be working on the Leatherman Flat bit soon. I am getting lots of requests for it from YouTube and email.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
HG