Bit adapter madness
-
Hmm, my brother is having a few difficulties finding a leatherman bit adapter that can fit the PST / minitool, anyone have any leads? How much does it cost in the states (since it will obviously be less expensive than in the UK)?
-
He should try the Universal Tool Adaptor:
I think it's a pretty handy little gizmo, and cheap enough. I think it runs about $20-25 or so.
Def
-
Here is a adapter for the Bear and Son Bear Jaws tool that fits over the rather big phillips driver.
.jpg)
.jpg)
-
I'm gonna have to get me one of them sooner or later....
Def
-
-
@prime77 said:
Another adapter is this one that fits on the Gerber Deisel, Freehand, and Suspension. The bits fit nicely with a magnetic holder but the adapter is a bit wobbley on the Gerber phillips driver.Thanks for the info, prime77. If you would be so kind, please answer the following questions:
-Is this adapter made by Gerber? Is there a source you would recommend?
-How bad is the wobble? Just a slight inconvenience? Bad enough to make using the adapter a PITA?
-Have you verified that the adapter fits all the Gerber multis you mention?
I am contemplating modding my new Suspension to add a bigger Phillips. But, if there's a bit adapter available that'll work with Suspension, that'd probably be a better way to go.
.
-
Yes the adapter you are asking about is made by Gerber. The one I have came with the Diesel model I have. The wobble isn't that bad but it's still there, not enough to make using the adapter difficult. I have the Suspension and the Diesel so I know that the adapter will fit those models. I understand from your modding Suspension thread that you may switch some of the Suspensions tools out for older Gerber tools. If you do switch out the Suspensions skinny phillips driver for the older one you will have to go with the adapter that J-Sews posted because the newer on won't fit over the thicker driver. Hope this helps :)
-
I found this adapter on a cheap tool. Outdoor Edge Trek Tool and thanks to Corrugated thread on SOG parts I put it on the SOG PowerLock and it fits fine. It takes up 5 implements so I don't see much of an advantage to having it. It looks cool though and if you want to use full size hex bits it will work for you.
.jpg)
.jpg)
-
@prime77 said:
Yes the adapter you are asking about is made by Gerber....If you do switch out the Suspensions skinny phillips driver for the older one you will have to go with the adapter that J-Sews posted because the newer on won't fit over the thicker driver. Hope this helps :)Thanks a lot, prime77. That does help.
This adapter looks to be a decent solution to immediately extend the functionality of my Suspension.
Eventually, if I am able to find a used Gerber tool with a bigger Phillips and file that will fit the Suspension, I do want to mod it.
However, this adapter would still work after the mod because my Suspension would still have the smaller Phillips.
So far, I haven't been able to find a source for these adapters.
The Gerber website is extraordinarily unhelpful at providing useful info on products. No decent pics, info on weights, dimensions, and no listings of exactly what accesories are available for the various products.
Is there anywhere that you know of to buy the correct bit adapter kit that will fit the Suspension?
Thanks again for your help.
.
-
I don't know of anywhere that just sells the bit adapter but I'll keep a look out for one.
-
This thread finally had the inevitable effect on me; I broke down and bought one of those Leatherman adapters. It came today, but.....
It didn't come with one of these fancy clamshell carrying cases like Prime has here:
Instead mine has a big dorky leather sheath, and a even dorkier plastic carrying contraption inside.

I like the adapter, but no way am I going to lug it around in a sheath that is bigger than my multitool sheath. :(
-
I thought that sheath actually looked pretty cool... :-[ :-[ :-[
But now I don't think I want to offer you a trade for it! :P
Def
-
Bob, that is the different style adapter from the one I have. I was wondering when being used with the SideClip does it fit into that cutout in the SideClips handles.
-
Mine is the Leatherman (Standard) Bit Adapter. It only fits the older PST, PST II, Mini-Tool, SideClip, etc. The paperwork that came with it is dated 1997, so apparently it is old stock. As ridiculous as this huge sheath and carrier are, Leatherman must have went back to the drawing board and came up with the plastic clamshell carrier at a later date.
Yes, the protruding tang fits exactly into the cutout in a SideClip's handle. I'm not sure what the purpose of the protruding tang is though?

-
Thanks Bob, it's strange that I find this stuff so interesting ::)
-
-
I agree. Man is known as the Tool Using Animal. What good is a tool using animal without a tool? Darwin would have slapped those other people for fouling up evolution.
Def
-
Thanks guys, It's good to know that I'm not alone.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login