Fall Follow-up Fixed Blade 30-day Challenge
-
@Alan K. said:
Day 14
Switching things up again with the CRKT Hunt'N Fisch by Larry Fischer. This knife ended the rotation for me during the last fixed blade challenge because I liked it so much I didn't carry anything else after this one. If you like the concept of a fixie for EDC but you aren't sold on the tactical design of most EDC fixed blades then you should have one of these. Get one!Not a bad looking knife!

-
That is one very nice looking Fixie!

-
@Nix said:
Day: 14 (bonus material)I had a chance to work on a knife I haven't finished making, today. The scales were looking pretty good after a couple of coats of linseed oil. Then I put the first-ever edge on the knife. This required a lot of grinding away--I had left the edge fairly fat for the heat treat. Grinding and sharpening made a big slurry during the process. So, naturally, the slurry got engrained into the fresh scales, making them look a bit dirty.


The blade is made from 1095 and it takes a wicked edge.
You have to love high carbon steel. :D "This knife will cut."I'm tempted to leave the scales as they are--they'll only get dirty later, right?--but it's a new knife, so I'll go back and try to clean them up a bit.

Nice, have been thinking of a similar design myself

Sent fra min FRD-L09 via Tapatalk
-
The scales don't look dirty to me. I suppose they might look different in person but it looks like a beautiful knife to me. It looks like it will be very useful. Nice work.

-
Thanks, Alan.
Yeah, in person was more obvious. Cleaned it up a bit and applied another coating of linseed oil/turpentine. Looks OK now (drying). I hope to start working on a sheath tomorrow.

-
Comis, I've been there myself, with 2 sons

Nice pup RF!
Jack, Colonial made a knife that they left the scales unfinished. The story behind it was that your own sweat would create its own finish and a story all it's own. Nice looking knife buddy!
-
@Barry Rowland said:
Comis, I've been there myself, with 2 sons
Nice pup RF!
Jack, Colonial made a knife that they left the scales unfinished. The story behind it was that your own sweat would create its own finish and a story all it's own. Nice looking knife buddy!
That's a story I can get behind. :D
My scales are Maple. I'm leaving them unstained. Just a bit of oil for protection. Then some of Colonial's 'Sweat and Use' finish.

-
@RF52 said:
What are you changing bearings on?Sent fra min FRD-L09 via Tapatalk
Steering box on an old dumper, one for each end of the worm gear

Thank's Ray

@Nix said:
Yeah, in person was more obvious. Cleaned it up a bit and applied another coating of linseed oil/turpentine. Looks OK now (drying). I hope to start working on a sheath tomorrow.
Can't go wrong with linseed oil, nice knife

-
Didn't like the green, so I re tied the handle in black type 95.

-
That'll work!

-
Right on!

-
@PitCarver said:
Didn't like the green, so I re tied the handle in black type 95.Looks good!
-
@Nix said:
Day: 14 (bonus material)I had a chance to work on a knife I haven't finished making, today. The scales were looking pretty good after a couple of coats of linseed oil. Then I put the first-ever edge on the knife. This required a lot of grinding away--I had left the edge fairly fat for the heat treat. Grinding and sharpening made a big slurry during the process. So, naturally, the slurry got engrained into the fresh scales, making them look a bit dirty.


The blade is made from 1095 and it takes a wicked edge.
You have to love high carbon steel. :D "This knife will cut."I'm tempted to leave the scales as they are--they'll only get dirty later, right?--but it's a new knife, so I'll go back and try to clean them up a bit.

Jack, do you use a belt or a jig to make the primary bevel? It looks really well done!

-
@Barry Rowland said:
Comis, I've been there myself, with 2 sons
Nice pup RF!
Jack, Colonial made a knife that they left the scales unfinished. The story behind it was that your own sweat would create its own finish and a story all it's own. Nice looking knife buddy!
Barry, now that they are both grown up and can stand on their own, it must be a great feeling. On one hand I hope the baby grows up healthy and happy, but on the other I kinda wish he could stay this young and cute a little longer, I am sure any parents would know what I am talking about.
:D -
Day 14

-
Day15
Survive Knife GSO10
This is a "chopper" knife made of 3V, I don't use it all too often for the outdoor due to its weight, but it's the perfect tool to chop open coconuts at home. The coconut juice starts to develop a little patina at the front end, so I put on a patina to the rest of the blade. Love the ergonomics of this knife, the big choil, tilted handle and finger grooves make really easy to chock up on the knife. I like the kydex sheath for the Suvive knife, the knife click into the sheath very securely, and the dangler option makes everything easy to carry and is universal to all their knives.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
