Ozark Trail MULTIFORCE - A Leatherman Inspired Multitool
-
Picked one up yesterday and other than the cross cut file, no magnet in the bit driver and a poor magnet in the extension it's VERY impressive for $40.00 after tax.
I've already added it to my Wira set to act as a second driver handle. It will also be as a second set of pliars along side my Swisstool or Spirit.
This is a far better tool at a better price than the Wingman in my estimation. As much as it PAINS me to say this WalMart got this one right. -
@Douglas said:
Picked one up yesterday and other than the cross cut file, no magnet in the bit driver and a poor magnet in the extension it's VERY impressive for $40.00 after tax.
I've already added it to my Wira set to act as a second driver handle. It will also be as a second set of pliars along side my Swisstool or Spirit.
This is a far better tool at a better price than the Wingman in my estimation. As much as it PAINS me to say this WalMart got this one right.I agree! One of the best budget multitools out there and it is one that is readily available! The bit driver does not need a magnet since the bits and the extender are held in by a ball bearing on them. I put a small button magnet in mine anyway, and now I can put standard bits in it and do not worry about having them fall out!
I bought a second one and am going to try to mod it at some point.
-
No walmarts down under :'(
-
I wonder who manufactured it for Wally World? The recent post ChopperCharles made about his first LM Wingman reminded me of this tool. Great to hear this tool continues to impress.
-
Crazy how slim the wave feels after handling this for a few days.
-
So some info from people who have been using the tool a bit and have messaged me on IG. There are some issues with the file, for one thing the diamond side isn't flat because they cut the file then applied the diamond coating after. This causes the edges to be higher than the middle of the file. In one case the entire diamond coating began to come off.
So far the two drawbacks:
bad file and the extender doesn't have magnetic retention. The rest still seams to work great. I really loved making this tool into a pocket knife since it has retention on both sides due to the slip joint mechanism. Cheers.
-
This is why Leatherman came out with the gimmicky Free series design. They knew Wave copies were coming and they couldn't do anything to stop it, the designer said so in a magazine interview. I might check one of these out during Christmas when they'll probably be under $20.
-
While it is definitely inspired by the Wave, it is definitely not a clone. It is wider, heaver, has a MUCH different (And better!) bit driver system. The magnet problem can be resolved easily by putting 2 small magnetic disks in the holder. It has no micro screw driver also. It is not better than a Wave by any means, but is more than worth what you pay for it!
-
@gregpost said:
This is why Leatherman came out with the gimmicky Free series design. They knew Wave copies were coming and they couldn't do anything to stop it, the designer said so in a magazine interview. I might check one of these out during Christmas when they'll probably be under $20.Interesting.
-
/post/1939114
I posted the magazine link in the original Free series announcement thread. This is probably the first of many legal Wave copies or based on wave platform designs that we will see. I'm actually a fan of patents expiring, I think it spurs innovation and increases good competition that benefits the consumer.
-
Can anyone kindly help me here getting one of this and ship it to the UK?
I will cover all cost.Thanks in advance
-
I think I’m going to have to get one of these next Walmart trip. I have the workpro with the scissors, which is ridiculously big and heavy. I actually love it, but without a pocket clip it will never see rotation as my EDC. But this Walmart wave-like tool might be just the ticket.
.Charles.
-
@ChopperCharles said:
I think I’m going to have to get one of these next Walmart trip. I have the workpro with the scissors, which is ridiculously big and heavy. I actually love it, but without a pocket clip it will never see rotation as my EDC. But this Walmart wave-like tool might be just the ticket.If you think that tool is heavy, you should get its big brother! It is about the size of the Leatherman Surge, but heavier. It is also made a bit better. The Multitforce is a tad bit heavier than a Wave, but the weight of most tools does not bother me anyway.
.Charles.
-
I might snag one of the bigger workpros if I can find it at a reasonable price. But again, without a pocket clip I'm unlikely to ever EDC it. But for a vehicle glove compartment, or a motorcycle tool roll, it'd be damn near perfect.
Charles.
-
So I just picked up the ozark trail multi force. I also have a leatherman wingman and the workpro with scissors to compare it to. I’ll do a big video review later, but I will post some observations here.
The ozark trail has the best scissors of the three. They cut through para cord in one snip, and they can be used to slice down thin wrapping paper like a good pair of regular scissors. The leatherman can do this for short distances with wrapping paper, but there is enough resistance that it starts tearing pretty quickly. the workpro is worse. Both the workpro and the leatherman have too-soft scissor springs, which results in the scissors sticking in the closed position quite a lot.
The crosscut file in the workpro is better than the crosscut file on the ozark... but the ozark has a diamond side and a third edge with file teeth. So it’s a draw. The wingman file is nice and sharp, but too small to be of any use.
The saw in the ozark has a longer cutting area and sharper teeth. It’s also machined better with the top narrower than the teeth. So it wins the saw battle against the workpro. The leatherman doesn’t have a saw.
The flat drivers bottle and can openers all work fine on all three. The leatherman and ozArk both have dual use can/bottle openers which can pierce the bottle top if you’re not careful. The workpro has a dedicated opener.
The Phillips driver on the workpro is very nicely made. But the ozark wins it with a 1/4 bit driver and extension.
The blades are all white similar. The wingman however has the shortest, and it’s a combo. All three are nice and sharp, but the ozark and wingman are tied. The workpro is good but slightly less sharp than the other too.
For outside opening tools, the ozark has a plain edged blade, serrated blade, file, and saw.
The work pro has PE blade, file, saw, and scissors.
The wingman has a blade and scissors.
The workpro has 5 additional outside opening tools.
The ozark has 4 internal tools
The wingman has 5 internal tools.
All workpro and ozark tools lock. Only the blade and scissors lock on the wingman.
Fit and finish, the ozark trail wins handily. I really liked the workpro when I got it, but neither it nor the wingman can hold a candle to the ozark trail multi force.
It has smooth rounded handles, well machined parts, and an intuitive locking mechanism. But the pliers are also far better.
Both the workpro and wingman have sprung plier jaws, and both have a fair bit of side to side play to the jaws. There is none in the ozark trail. The ozark also has the smallest handle splay, which make them the most comfortable to use. The jaws open wider than the other two as well, and the plier Head is also thicker than the other two.
Like the work pro, some of the ozark’s jaw space is taken by a protruding cutter, though the jaws appear closer in shape and length to the wingman jaws.
The cutters are excellent. Beyond excellent, really. They can cut individual strands of #000 steel wool. The workpro is the next best, and the wingman is abysmal.
I like the workpro. I think it’s a great tool with a lot to offer in this price range. But the ozark trail multi force is the winner in my book. It’s the most comfortable to use, with the best jaws, best cutters, best scissors, best Phillips driver, best saw, and the file is a tie with the workpro. It also comes with a bit driver extension.
The workpro has two additional flat drivers and an awl, but lacks the serrated blade. It has the second best jaws and cutters. Unfortunately it does not have a pocket clip.
The wingman is a distant also-ran. It’s more expensive than either the workpro or the ozark trail, and it has a ridiculous amount of side to side play in the jaws. The cutters don’t meet and are only good for household solid copper wire. And even then, only after I filed down the tips of the jaws a bit so the cutters came closer to meeting. The scissors are the largest of the lot, but the spring is weak and the scissors often stick in the closed position. It has the fewest outside opening tools and none of the internal tools - including the screwdrivers - lock. The Phillips is also a 2.5D.
The workpro runs about $30. The ozark trail $38. The wingman is $60!!!
For the money, the ozaek trail is the clear winner. Fit and finish is excellent, it’s the most comfortable to use and has the most robust jaws and best scissors.
Charles.
-
The scissors were by far the biggest surprise...they utterly destroy every Leatherman scissor except a surge (which is amazing but also not really the same thing).
-
@Happy Gilmore said:
The scissors were by far the biggest surprise...they utterly destroy every Leatherman scissor except a surge (which is amazing but also not really the same thing).The free series and juice has a better scissors, but its definitely has a good pair compared to the wave.
Does anyone know where to buy bits for this?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

