ZapWizard's Leatherman Free P4 Mods
-
Bloody brilliant!
-
I've only seen the video and not listened to it, so haven't followed the comments and I'm not sure whether you covered this:
On the topic of making the Surge blades fit, would it be an option to make the shank cavity to the depth of the LM shank, with the exception of a circular nub at the position of the hole in the LM shank that locally restricts the cavity depth to the thickness of a Bosch shank *)? Maybe that is sufficient to hold both types. Possibly in combination with a spring with a larger contact area on the shank...
Just thinking

*) Edit: maybe just one of the Bosch thicknesses... 1.25?
-
I CAN'T WAIT for the t-shank holder and the holster with bit slots to be available ... This is gonna cost me a lot!
Regarding the t-shank thickness issue:
On the topic of making the Surge blades fit, would it be an option to make the shank cavity to the depth of the LM shank, with the exception of a circular nub at the position of the hole in the LM shank that locally restricts the cavity depth to the thickness of a Bosch shank *)? Maybe that is sufficient to hold both types. Possibly in combination with a spring with a larger contact area on the shank...
So that circular nub would go on the orange part, if you refer to Zap's post above? Would make sense to me. It would greatly reduce the thickness needed on the other side's "springy arm".
Hey Zap, on another topic, I was wondering if your blade tabs would be reversible? Let's say I'm a big goofy lefty (which I may or may not actually be), and I decided to switch the serrated and the straight blades so the latter is next to my left thumb when I hold the tool. I noticed that the hole egde is ever so sligthly sharper on one side than on the other. Would you tab fit on both sides of the blade so I can use them with my current configuration?
- The dovetail guy on Shapeways ;)
-
Outstanding work, Zapwizard!
Goes to show how much potential this platform has and what LM decided to do with it 
-
@Matpar_McWolfie said:
...Regarding the t-shank thickness issue:So that circular nub would go on the orange part, if you refer to Zap's post above? Would make sense to me. It would greatly reduce the thickness needed on the other side's "springy arm".
...
Yup, that's where it would go, thanks for prompting the clarification

-
The flat bit driver is now available to purchase.
Video:
https://www.youtube.com/watch?v=HYbHVKSohmsThe holster for the FREE P2 is also available:
https://www.youtube.com/watch?v=DPiL9JhfnAgAnd the FREE P2 and P3 bit-holder holsters are also now available. 4mm, Flat, and Flat with Bit extender options.

Finally, the holster for the ST300 is also ready
https://www.youtube.com/watch?v=2mSGhriP1akShop link in my signature below.
-
Very nice

-
@ZapWizard said:
The flat bit driver is now available to purchase.
Video:The holster for the FREE P2 is also available:
And the FREE P2 and P3 bit-holder holsters are also now available. 4mm, Flat, and Flat with Bit extender options.

Finally, the holster for the ST300 is also ready
Shop link in my signature below.
So impressed would consider getting one of these series, along with your mods and accessories! Awesome stuff. :o
-
Very nice job, Zap
and love the sheaths 
Also welcome to
Matpar 
-
Hello all!
Long time lurker, and just registered today!
I have been obsessing over your work, ZapWizard, since this thread was born.
The LM FlatBit system is a must-have for my needs, and I was sad to see the Free P4 did not have it. That left me torn between carrying dad’s old Wave+ and my shiny new P4...I opted for the P4 as my EDC.
Then I discovered your work, and the rest is history.
My FlatBit driver and Thumb Tabs are in processing from ShapeWays, as of last Friday! Anxiously awaiting their arrival!
I know I’m new here, but I have two burning questions that I could no longer resist asking:
**1. Have you figured out the torque specs for the Chicago screw pivots that hold the small tools (and soon my ZW FlatBit driver) in place? **
- Contact with LM reveals that it’s a proprietary spec, which they wouldn’t share. - I’d really like to get this tool back to factory specs when I’m done installing my mod, even though I know my warranty will be out the window.
2. Do you have any plans for a horizontal version of the holster for the P4?
- I’ll admit, I’m a big ol’ fatty. My love handles make vertical carry uncomfortable.
- I also, however, dabble in the art of leatherwork...And I’ve been mentally designing a horizontal EDC pouch for the P4, a FlatBit caddy, the FlatBit extender, and a small Craftsman ratchet.
Sorry for the short novel here. Just really excited to receive my items, and to be able to communicate with a veritable “god of mod”...and, of course, all the members here!
Also, sorry for lurking so long!
I hope I can bring some value to this forum / thread!
-
@hbcorpse said:
Long time lurker, and just registered today!Thanks for the compliments, and welcome. Don't worry I lurked here for years before I finally made a post.
I have a torque meter at work that I can borrow to measure the existing torque on those screws. My P4 has been taken apart, but I have only messed with one screw on my P2. So In theory, I can use the torque wrench to measure how much it takes before they tighten/loosen to see what the existing torque is. But then to repeat that you need a torque wrench anyways.
In reality you can do this just by hand like I do in my videos. You get a feel for the tension and adjust it looser/tighter.
This has been requested a few times, and I have put some thought into it. It probably would have to be done as an open loop. I may take another crack at the design soon, now that I know the open loop is stronger than I expected.
The catch is it wouldn't hold any bits, as they would be shoved up against the belt. I have been thinking of making a stand-along bit holder for the flat bits, something that could be removed from the belt and used as a handle on the extender. -
@ZapWizard said:
Thanks for the compliments, and welcome. Don't worry I lurked here for years before I finally made a post.I have a torque meter at work that I can borrow to measure the existing torque on those screws. My P4 has been taken apart, but I have only messed with one screw on my P2. So In theory, I can use the torque wrench to measure how much it takes before they tighten/loosen to see what the existing torque is. But then to repeat that you need a torque wrench anyways.
In reality you can do this just by hand like I do in my videos. You get a feel for the tension and adjust it looser/tighter.
This has been requested a few times, and I have put some thought into it. It probably would have to be done as an open loop. I may take another crack at the design soon, now that I know the open loop is stronger than I expected.
The catch is it wouldn't hold any bits, as they would be shoved up against the belt. I have been thinking of making a stand-along bit holder for the flat bits, something that could be removed from the belt and used as a handle on the extender.Horizontal holster would be my jam as well, your almost my singluar driving reason to consider the P4 at this point lol.
-
This is just amazing work!

-

@Dutch_Tooler said:
I've only seen the video and not listened to it, so haven't followed the comments and I'm not sure whether you covered this:On the topic of making the Surge blades fit, would it be an option to make the shank cavity to the depth of the LM shank, with the exception of a circular nub at the position of the hole in the LM shank that locally restricts the cavity depth to the thickness of a Bosch shank *)? Maybe that is sufficient to hold both types. Possibly in combination with a spring with a larger contact area on the shank...
Just thinking

*) Edit: maybe just one of the Bosch thicknesses... 1.25?
Just curious whether you've had time to consider this Zap?
-
@Dutch_Tooler said:
Just curious whether you've had time to consider this Zap?I guess I missed that post, sorry. There isn't enough room for multiple cutouts. However, I did work on redesigning the t-shank. The first thing I tried was multiple cutouts for multiple thicknesses, and the tolerances are just too small. (0.25mm steps). I then tried to figure out how to get a stainless steel spring into the design. Something like McMaster 9716K360. There was just no way to hold a off the shelf tiny spring, and I am not ready to start making custom springs.


Here is the design I came up with, and ordered prototypes for just earlier today.
It uses a two halves, one of Steel, and the other Nylon. The steel part has the T-Shank cutout, 1mm deep on one side (Sliding side), and 2mm deep on the other side. All of the back and forth cutting torque should end up on the steel part. Some sideways torque might flex the nylon part, but it should spring right back.
The nylon half has a spring-loaded arm. The arm is set to hold a bit of force on a 1mm blade, but accommodate up to a 2mm blade. The spring arm is hinged on one side, and has a stop on the other side to prevent if from moving too far.
Two dove tailed areas lock the two parts together upon closing, hopefully ensuring the nylon doesn't just bend apart. I have no idea if will work until I get the prototypes. -
I don’t really have anything to add to this thread other than saying that it’s indescribably awesome and ZapWizard is a legend.
-

@ZapWizard: that looks like it should work. The spring acts to close the lower left dovetail in the pic - nice touch!
BTW, what I was suggesting was not a multiple cutout - just a single one, but with a circular nub protruding from the cutout's bottom, in size and position to fall just inside the hole in the LM T-shank, while other thinner T-shanks (Bosch et al. - these lack holes) lie on top of the nub. The nub might also be sprung, come to think of it.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

