ZapWizard's Leatherman Free P4 Mods
-
This is just amazing work!

-

@Dutch_Tooler said:
I've only seen the video and not listened to it, so haven't followed the comments and I'm not sure whether you covered this:On the topic of making the Surge blades fit, would it be an option to make the shank cavity to the depth of the LM shank, with the exception of a circular nub at the position of the hole in the LM shank that locally restricts the cavity depth to the thickness of a Bosch shank *)? Maybe that is sufficient to hold both types. Possibly in combination with a spring with a larger contact area on the shank...
Just thinking

*) Edit: maybe just one of the Bosch thicknesses... 1.25?
Just curious whether you've had time to consider this Zap?
-
@Dutch_Tooler said:
Just curious whether you've had time to consider this Zap?I guess I missed that post, sorry. There isn't enough room for multiple cutouts. However, I did work on redesigning the t-shank. The first thing I tried was multiple cutouts for multiple thicknesses, and the tolerances are just too small. (0.25mm steps). I then tried to figure out how to get a stainless steel spring into the design. Something like McMaster 9716K360. There was just no way to hold a off the shelf tiny spring, and I am not ready to start making custom springs.


Here is the design I came up with, and ordered prototypes for just earlier today.
It uses a two halves, one of Steel, and the other Nylon. The steel part has the T-Shank cutout, 1mm deep on one side (Sliding side), and 2mm deep on the other side. All of the back and forth cutting torque should end up on the steel part. Some sideways torque might flex the nylon part, but it should spring right back.
The nylon half has a spring-loaded arm. The arm is set to hold a bit of force on a 1mm blade, but accommodate up to a 2mm blade. The spring arm is hinged on one side, and has a stop on the other side to prevent if from moving too far.
Two dove tailed areas lock the two parts together upon closing, hopefully ensuring the nylon doesn't just bend apart. I have no idea if will work until I get the prototypes. -
I don’t really have anything to add to this thread other than saying that it’s indescribably awesome and ZapWizard is a legend.
-

@ZapWizard: that looks like it should work. The spring acts to close the lower left dovetail in the pic - nice touch!
BTW, what I was suggesting was not a multiple cutout - just a single one, but with a circular nub protruding from the cutout's bottom, in size and position to fall just inside the hole in the LM T-shank, while other thinner T-shanks (Bosch et al. - these lack holes) lie on top of the nub. The nub might also be sprung, come to think of it.
-
Hmmm... the LM file and saw blade in your video appear to have a hole in the shank but those on the LM website don't...? I think I need to check that...
Edit: mine has the hole, where the Phillip's head is pointing at...



-
I don't want to rely on the hole being there, since most T-Shanks don't have it. I want to accommodate as many different blades as possible. Even massage balls

Grinding down the Leatherman to fit the Bosch is easily done, just any hand file will do it, and it is removing just about 0.1mm of material. -
I get that but it would allow for a post to go through the LM blade, just as Duch_Tooler suggested. The post could squeeze the bosch blade into place, making it super stable, while allowing for the Leatherman blade to still fit.
That being said, I think the latest iteration of your design allows for more blade thicknesses to fit. If it works, that is one hell of an engineering prowess! Can't wait to see and buy!
Also, I was wondering if you saw that question?
Hey Zap, on another topic, I was wondering if your blade tabs would be reversible? Let's say I'm a big goofy lefty (which I may or may not actually be), and I decided to switch the serrated and the straight blades so the latter is next to my left thumb when I hold the tool. I noticed that the hole egde is ever so sligthly sharper on one side than on the other. Would you tab fit on both sides of the blade so I can use them with my current configuration?
-
Think Leatherman used t-shank blades with holes to keep them inside their newer blade exchanger using a flat spring iirc. Seems that would keep blade options fairly limited, requiring a hole. Making an exchanger that does not require the hole would keep blade options more open. Ought to break away from their standards, make an exchanger for t-shank tools without the need for holes to hold them inside.

-
@ZapWizard said:
I guess I missed that post, sorry. There isn't enough room for multiple cutouts. However, I did work on redesigning the t-shank. The first thing I tried was multiple cutouts for multiple thicknesses, and the tolerances are just too small. (0.25mm steps). I then tried to figure out how to get a stainless steel spring into the design. Something like McMaster 9716K360. There was just no way to hold a off the shelf tiny spring, and I am not ready to start making custom springs.

Here is the design I came up with, and ordered prototypes for just earlier today.
It uses a two halves, one of Steel, and the other Nylon. The steel part has the T-Shank cutout, 1mm deep on one side (Sliding side), and 2mm deep on the other side. All of the back and forth cutting torque should end up on the steel part. Some sideways torque might flex the nylon part, but it should spring right back.
The nylon half has a spring-loaded arm. The arm is set to hold a bit of force on a 1mm blade, but accommodate up to a 2mm blade. The spring arm is hinged on one side, and has a stop on the other side to prevent if from moving too far.
Two dove tailed areas lock the two parts together upon closing, hopefully ensuring the nylon doesn't just bend apart. I have no idea if will work until I get the prototypes.Seriously...we are not worthy!
-
@Outback in Idaho said:
Think Leatherman used t-shank blades with holes to keep them inside their newer blade exchanger using a flat spring iirc. Seems that would keep blade options fairly limited, requiring a hole. Making an exchanger that does not require the hole would keep blade options more open. Ought to break away from their standards, make an exchanger for t-shank tools without the need for holes to hold them inside.
Fair enough... but my idea for the nub is that it should only be able to use the hole in the LM T-shank - whilst the normal (thinner, non-holed) T-shanks on Bosch etc. blades should not be impinged. That is to say: make the nub only as high as needed to provide in-hole support for LM blades, but not so high as to come into conflict with the thinner blades: i.e. the flat upper side of the nub supports any non-holed blades.
I just got myself another set of spare LM blades - these are holed too, seems to be standard now.
Anyway, let's see if ZapWizard's new prototype works.

-
@ZapWizard said:
I don't want to rely on the hole being there, since most T-Shanks don't have it. I want to accommodate as many different blades as possible. Even massage balls
Grinding down the Leatherman to fit the Bosch is easily done, just any hand file will do it, and it is removing just about 0.1mm of material.Fair enough, but see my previous post - the nub is not intended to interfere with thinner Bosch etc. blades and the thicker LM ones now come standard with holes...
-
Just a question if I may ZapWizard - how thick is the blade holder going to be at the tang? Checking various options on which tools to retain. Thanks

-
@Matpar_McWolfie said:
Also, I was wondering if you saw that question?The T-Shank will be reversible. The design is now symmetrical.
@Dutch_Tooler said:
Just a question if I may ZapWizard - how thick is the blade holder going to be at the tang? Checking various options on which tools to retain. Thanks
It will be 0.17in thick at the hinge. The T-Shank holder will only be able to be installed where the saw is now located, along with removal of a single thin implement and the stacking washers. It must have a spring next to it, as I use that tiny extra bit of space to add some material. I removed the file on mine initially, but I think I am going to put that back and remove the bottle opener instead. If you instead decide to remove a 0.060" thick implement (awl or ruler), then you just keep one of the 0.01" thick spacer washers.
My 2nd order is still in production. Shapeways isn't exactly fast. Estimated ship date is Nov 19th, but they usually show up earlier.
-
@ZapWizard said:
(...) Shapeways isn't exactly fast. (...)I hear you... there are a few items waiting for various deliveries to you and me both :D

-
@Dutch_Tooler said:
I hear you... there are a few items waiting for various deliveries to you and me both :DNice carry set!

-
Thanks Ray - well, not all of the items will be in the kit but I've ordered one of the holsters with room for 7 bits and the extender, as well as the bit driver. Can't wait till they get here - same for progress on the T-shank holder :ahhh
What's missing on the holster for my particular needs is a holder for one of the saw/file blades and the two long MUT bits. But I have a 3D printer and I'm toying with the idea of adding such a holder to the holster in some hopefully non-destructive manner ;) :D
-
I am sure you will figure out a way to do that!

-
Meanwhile...

Box from Shapeways... :ahhh
I was wrong... the holster only holds three bits since the variant I chose for longevity's sake is the one to which one can fit a metal belt clip (which hasn't arrived yet). No great deal. The bit driver fits like a glove and works well

Thanks are due to ZapWizard for his designs



Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login