ZapWizard's Leatherman Free P4 Mods
-
I get that but it would allow for a post to go through the LM blade, just as Duch_Tooler suggested. The post could squeeze the bosch blade into place, making it super stable, while allowing for the Leatherman blade to still fit.
That being said, I think the latest iteration of your design allows for more blade thicknesses to fit. If it works, that is one hell of an engineering prowess! Can't wait to see and buy!
Also, I was wondering if you saw that question?
Hey Zap, on another topic, I was wondering if your blade tabs would be reversible? Let's say I'm a big goofy lefty (which I may or may not actually be), and I decided to switch the serrated and the straight blades so the latter is next to my left thumb when I hold the tool. I noticed that the hole egde is ever so sligthly sharper on one side than on the other. Would you tab fit on both sides of the blade so I can use them with my current configuration?
-
Think Leatherman used t-shank blades with holes to keep them inside their newer blade exchanger using a flat spring iirc. Seems that would keep blade options fairly limited, requiring a hole. Making an exchanger that does not require the hole would keep blade options more open. Ought to break away from their standards, make an exchanger for t-shank tools without the need for holes to hold them inside.

-
@ZapWizard said:
I guess I missed that post, sorry. There isn't enough room for multiple cutouts. However, I did work on redesigning the t-shank. The first thing I tried was multiple cutouts for multiple thicknesses, and the tolerances are just too small. (0.25mm steps). I then tried to figure out how to get a stainless steel spring into the design. Something like McMaster 9716K360. There was just no way to hold a off the shelf tiny spring, and I am not ready to start making custom springs.

Here is the design I came up with, and ordered prototypes for just earlier today.
It uses a two halves, one of Steel, and the other Nylon. The steel part has the T-Shank cutout, 1mm deep on one side (Sliding side), and 2mm deep on the other side. All of the back and forth cutting torque should end up on the steel part. Some sideways torque might flex the nylon part, but it should spring right back.
The nylon half has a spring-loaded arm. The arm is set to hold a bit of force on a 1mm blade, but accommodate up to a 2mm blade. The spring arm is hinged on one side, and has a stop on the other side to prevent if from moving too far.
Two dove tailed areas lock the two parts together upon closing, hopefully ensuring the nylon doesn't just bend apart. I have no idea if will work until I get the prototypes.Seriously...we are not worthy!
-
@Outback in Idaho said:
Think Leatherman used t-shank blades with holes to keep them inside their newer blade exchanger using a flat spring iirc. Seems that would keep blade options fairly limited, requiring a hole. Making an exchanger that does not require the hole would keep blade options more open. Ought to break away from their standards, make an exchanger for t-shank tools without the need for holes to hold them inside.
Fair enough... but my idea for the nub is that it should only be able to use the hole in the LM T-shank - whilst the normal (thinner, non-holed) T-shanks on Bosch etc. blades should not be impinged. That is to say: make the nub only as high as needed to provide in-hole support for LM blades, but not so high as to come into conflict with the thinner blades: i.e. the flat upper side of the nub supports any non-holed blades.
I just got myself another set of spare LM blades - these are holed too, seems to be standard now.
Anyway, let's see if ZapWizard's new prototype works.

-
@ZapWizard said:
I don't want to rely on the hole being there, since most T-Shanks don't have it. I want to accommodate as many different blades as possible. Even massage balls
Grinding down the Leatherman to fit the Bosch is easily done, just any hand file will do it, and it is removing just about 0.1mm of material.Fair enough, but see my previous post - the nub is not intended to interfere with thinner Bosch etc. blades and the thicker LM ones now come standard with holes...
-
Just a question if I may ZapWizard - how thick is the blade holder going to be at the tang? Checking various options on which tools to retain. Thanks

-
@Matpar_McWolfie said:
Also, I was wondering if you saw that question?The T-Shank will be reversible. The design is now symmetrical.
@Dutch_Tooler said:
Just a question if I may ZapWizard - how thick is the blade holder going to be at the tang? Checking various options on which tools to retain. Thanks
It will be 0.17in thick at the hinge. The T-Shank holder will only be able to be installed where the saw is now located, along with removal of a single thin implement and the stacking washers. It must have a spring next to it, as I use that tiny extra bit of space to add some material. I removed the file on mine initially, but I think I am going to put that back and remove the bottle opener instead. If you instead decide to remove a 0.060" thick implement (awl or ruler), then you just keep one of the 0.01" thick spacer washers.
My 2nd order is still in production. Shapeways isn't exactly fast. Estimated ship date is Nov 19th, but they usually show up earlier.
-
@ZapWizard said:
(...) Shapeways isn't exactly fast. (...)I hear you... there are a few items waiting for various deliveries to you and me both :D

-
@Dutch_Tooler said:
I hear you... there are a few items waiting for various deliveries to you and me both :DNice carry set!

-
Thanks Ray - well, not all of the items will be in the kit but I've ordered one of the holsters with room for 7 bits and the extender, as well as the bit driver. Can't wait till they get here - same for progress on the T-shank holder :ahhh
What's missing on the holster for my particular needs is a holder for one of the saw/file blades and the two long MUT bits. But I have a 3D printer and I'm toying with the idea of adding such a holder to the holster in some hopefully non-destructive manner ;) :D
-
I am sure you will figure out a way to do that!

-
Meanwhile...

Box from Shapeways... :ahhh
I was wrong... the holster only holds three bits since the variant I chose for longevity's sake is the one to which one can fit a metal belt clip (which hasn't arrived yet). No great deal. The bit driver fits like a glove and works well

Thanks are due to ZapWizard for his designs



-
@ZapWizard said:
I have a torque meter at work that I can borrow to measure the existing torque on those screws. My P4 has been taken apart, but I have only messed with one screw on my P2. So In theory, I can use the torque wrench to measure how much it takes before they tighten/loosen to see what the existing torque is. But then to repeat that you need a torque wrench anyways.In reality you can do this just by hand like I do in my videos. You get a feel for the tension and adjust it looser/tighter.
This has been requested a few times, and I have put some thought into it. It probably would have to be done as an open loop. I may take another crack at the design soon, now that I know the open loop is stronger than I expected.
The catch is it wouldn't hold any bits, as they would be shoved up against the belt. I have been thinking of making a stand-along bit holder for the flat bits, something that could be removed from the belt and used as a handle on the extender.Any luck with the torque meter?
Still haven’t found time to do the install yet, but maybe I’ll take a crack at it today...at the very least, the thumb tabs are going in!
————
As for the horizontal carry...This might be a stretch of an idea, but...
Picture the holster standing vertically:
-
What if you moved the Bit Extender to the left of the main channel, which would put it “on top” of the holster, when mounted on the belt...assuming it’s mounted on someone’s right side.
-
Then, take the beautifully designed Bit holder slots and put them to the right of the main channel, which would put them on the “bottom” of the holster...
Removing the Bits from the back face of the holster would provide access to them on a horizontal carry.
-
-
@Dutch_Tooler said:
Meanwhile...
Box from Shapeways... :ahhh
I was wrong... the holster only holds three bits since the variant I chose for longevity's sake is the one to which one can fit a metal belt clip (which hasn't arrived yet). No great deal. The bit driver fits like a glove and works well

Thanks are due to ZapWizard for his designs

I like that compactness

-
Love the sheath and the bit holder
I have a sheath from Zap that holds the Wave/Charge tools with room for bits in the back and the extender on the side and am very pleased with it

-
Playing around with the holster I conclude it is a very well thought out piece of kit. The Free P4 fits in four ways if you take the pocket clip off, two ways if you leave it on, including two or one respectively with extended implements (although I'd be careful doing that with the long tools, especially the bladed ones ;) ). It uses the locks on the Free to lock the tool inside the holster, irrespective of how you put it in, so there is no falling out.
The integrated bit holders are a nice feature for frequently used bits - although the number of three is a bit limited - this is down to my choice for the metal belt clip variant, other variants have 6 or 7 spaces I think. The bit extender holder works well too. The whole thing seems quite solid, but I won't know to which extent until after I start to wear it.
Final verdict on wearability once the belt clip arrives (taking the slow boat from China, it seems).I have thought of adding some extra holders for saw/file blades and long MUT bits, but can't seem to find anything that integrates well with the holster design while avoiding a haphazard DIY look and thus detracting from its otherwise professional look - also on balance I think I may need to carry at least one LM bit card for flexibility. I'll probably end up assembling some kit in a small extra holster or pouch.
-
Can't wait to see what you come up with, DT


-
@Dutch_Tooler said:
Box from Shapeways...Your kit looks great.
@hbcorpse said:
Any luck with the torque meter?As for the horizontal carry...
I don't think the torque meter will help, it is easy to just tweak it until the tools move properly. Because they used chemical thread locker, torque is less a factor in holding the screw in place.
I am working on a few ideas for horizontal carry, however it won't include bit holders, as you would only end up with just a few, or an oversized holder. Most who have requested horizontal carry want less bulk above/below the belt line.@Dutch_Tooler said:
Playing around with the holster I conclude it is a very well thought out piece of kit.Thanks for your nice comments.
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
I also got a box from Shapeways, my 2nd prototype of the T-Shank holder arrived. It shows real promise. I will cycle exchanging the blades a few dozen times to ensure the nylon will hold up, but so far it seems to be close to being ready.
I just need to tweak the profile so it closes/opens a bit better, and tweak a bit of the dimensions to make it work out of the box. -
Looking great

How much thickness will one have to grind off from a LM shank?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login