Opinel Knifes
-
@Gareth said:
Essentially they become friction folders. You can give the pivot pin a bask if it becomes a bit loose. As with all non-locking knives they are perfectly safe as long as you remember they are non-locking.I didn't realise you could tighten them up - that might help save a few plasters :)
-
Spooky coincidence, these listed today :o :o
http://www.heinnie.com/product.asp?s=cppztd1502137&strParents=&CAT_ID=469&P_ID=4069
-
Essentially they become friction folders. You can give the pivot pin a bask if it becomes a bit loose. As with all non-locking knives they are perfectly safe as long as you remember they are non-locking.
I didn't realise you could tighten them up - that might help save a few plasters :)
I did that with mine, turned it into a nail breaker, took a lot of work to made it loose again. :oops:
@Micky d said:
Spooky coincidence, these listed today :o :ohttp://www.heinnie.com/product.asp?s=cppztd1502137&strParents=&CAT_ID=469&P_ID=4069
Interesting, the blade marking is different. Handle is same as mine but blade stamping on mine has the finger crown horizontal on the left and OPINEL FRANCE on right.
-
Essentially they become friction folders. You can give the pivot pin a bask if it becomes a bit loose. As with all non-locking knives they are perfectly safe as long as you remember they are non-locking.
I didn't realise you could tighten them up - that might help save a few plasters :)
I did that with mine, turned it into a nail breaker, took a lot of work to made it loose again.

Yes, just a very little
baskbash would do it. -
Essentially they become friction folders. You can give the pivot pin a bask if it becomes a bit loose. As with all non-locking knives they are perfectly safe as long as you remember they are non-locking.
I didn't realise you could tighten them up - that might help save a few plasters :)
I did that with mine, turned it into a nail breaker, took a lot of work to made it loose again.

Yes, just a very little
baskbash would do it.I believe the "traditional" way of opening the knife is to tap the heel of the knife against something (your shoe I think) making the blade come clear of the handle. Then you have a lot more to grip rather than just using the nail nick.
-
I tried that before, either I suck at it or it's not very effective. If the blade is lose enough to come out, it won't be any effort to pull it out via nailpick to begin with. If it's a nailbreaker it won't come out no matter how hard I smack it.
-
I think your right actually. I can do it with my two, but both are loose enough that I don't need to. ::) Back to the drawing board.
-
Blade Forums had a thread on this knife recently. Here it is.
-
Of course its really easy to make any opi non-locking. Just pull off the locking ring or shove some epoxy under it. Job done :D
Neil
Is there much of a snap on it when you do that? Don't want it folding up on her dainty little fingers :o
A non locking opinel :o good god no! Those rings are there for a purpose. Opinels are great knives but they are lethal when they decide to fold up on you! Son of Hedge Kid nearly took the end of his finger off with one of those forgetting to put the lock on. Doh!
[quote author=Gareth link=topic=10872.msg203113#msg203113 date=1241687940]
Essentially they become friction folders. You can give the pivot pin a bask if it becomes a bit loose. As with all non-locking knives they are perfectly safe as long as you remember they are non-locking.I didn't realise you could tighten them up - that might help save a few plasters :)
I did that with mine, turned it into a nail breaker, took a lot of work to made it loose again.

Yes, just a very little
baskbash would do it.I believe the "traditional" way of opening the knife is to tap the heel of the knife against something (your shoe I think) making the blade come clear of the handle. Then you have a lot more to grip rather than just using the nail nick.
[/quote]We used to use opinels all the time on the farm and when they get cacked up with mud and other detrius they refuse to open. In addition to Gareth's explanation above - tap it hard on a hard surface (wood) if that doesn't work, spray some WD40 into the pivot joint, rest the tapping point on the bench and gently tap the back of the tapping point with a hammer. You can interpret "gently" anyway you like depending on the age of the knife and your frustration levels >:D They can take a fair whack. If you value your handle, put a piece of wood between the tapping point and the hammer as your frustration increases.!
-
Dead good knives :) Got a stainless No.8 from the last time I was in France. Etched the blade and carved the grip a little. They're supposed to seize up a little if they get damp, but I waterproofed the top with Vaseline (spread it on to the top liberally, gently heat with a lighter until it gets thin enough to sink in, wipe off excess) so I've never found that a problem. They take really good edges with little effort, even the stainless ones.
-
@BenH said:
Dead good knives :) Got a stainless No.8 from the last time I was in France. Etched the blade and carved the grip a little. They're supposed to seize up a little if they get damp, but I waterproofed the top with Vaseline (spread it on to the top liberally, gently heat with a lighter until it gets thin enough to sink in, wipe off excess) so I've never found that a problem. They take really good edges with little effort, even the stainless ones.I want to buy a Opinel 12 as a bag/pack cooking knife, but I'm worried about getting the handle wet. What is the best way to try and waterproof the handle? I've seen some of the ideas here and they look pretty good, but what if I wrap the handle in duct tape? I just need to be able to clean the knife after cooking.
Anyone use a 12 for cooking?
-
John, it sounds like you need a large Cold Steel Twistmaster
:DSorry John I couldn't help myself. :D
-
I used mine a bit to carve turkey this Thanksgiving past. I usually just stick the "blade" in hot soapy water
and just run a damp rag over the wood. It might stiffen up a bit but usually goes back to it's normal ease
of open in awhile.
I have one Opinel and love it. I did mod the handle on it for comfort. The older it gets the more character
the blade seems to show. -
I saw a #12 slim the other day and it was preeeeeeeeetty, but at $40 it's hard to justify for an opinel.
-
Dead good knives :) Got a stainless No.8 from the last time I was in France. Etched the blade and carved the grip a little. They're supposed to seize up a little if they get damp, but I waterproofed the top with Vaseline (spread it on to the top liberally, gently heat with a lighter until it gets thin enough to sink in, wipe off excess) so I've never found that a problem. They take really good edges with little effort, even the stainless ones.
I want to buy a Opinel 12 as a bag/pack cooking knife, but I'm worried about getting the handle wet. What is the best way to try and waterproof the handle? I've seen some of the ideas here and they look pretty good, but what if I wrap the handle in duct tape? I just need to be able to clean the knife after cooking.
Anyone use a 12 for cooking?
GG something I learned for kukri wooden handles,place the handle in a jar of Raw linseed oil for 72 hrs and then in boiled linseed oil for a further 48 hrs then when dry use beeswax to finish off

-
Dead good knives :) Got a stainless No.8 from the last time I was in France. Etched the blade and carved the grip a little. They're supposed to seize up a little if they get damp, but I waterproofed the top with Vaseline (spread it on to the top liberally, gently heat with a lighter until it gets thin enough to sink in, wipe off excess) so I've never found that a problem. They take really good edges with little effort, even the stainless ones.
I want to buy a Opinel 12 as a bag/pack cooking knife, but I'm worried about getting the handle wet. What is the best way to try and waterproof the handle? I've seen some of the ideas here and they look pretty good, but what if I wrap the handle in duct tape? I just need to be able to clean the knife after cooking.
Anyone use a 12 for cooking?
GG something I learned for kukri wooden handles,place the handle in a jar of Raw linseed oil for 72 hrs and then in boiled linseed oil for a further 48 hrs then when dry use beeswax to finish off

John, if I do that can I wash the knife without the worry of the wood splitting? In other words, will it be a good food prep knife? Thanks for the tip!

-
Dead good knives :) Got a stainless No.8 from the last time I was in France. Etched the blade and carved the grip a little. They're supposed to seize up a little if they get damp, but I waterproofed the top with Vaseline (spread it on to the top liberally, gently heat with a lighter until it gets thin enough to sink in, wipe off excess) so I've never found that a problem. They take really good edges with little effort, even the stainless ones.
I want to buy a Opinel 12 as a bag/pack cooking knife, but I'm worried about getting the handle wet. What is the best way to try and waterproof the handle? I've seen some of the ideas here and they look pretty good, but what if I wrap the handle in duct tape? I just need to be able to clean the knife after cooking.
Anyone use a 12 for cooking?
GG something I learned for kukri wooden handles,place the handle in a jar of Raw linseed oil for 72 hrs and then in boiled linseed oil for a further 48 hrs then when dry use beeswax to finish off

John, if I do that can I wash the knife without the worry of the wood splitting? In other words, will it be a good food prep knife? Thanks for the tip!

Should be fine if done correctly and maintained what it does is seal the wood ;) what you could do if your not 100% sure is test the method on a piece of any wood first
this method is also great for restoring tired looking wood handles or scales ;) -
Splitting is never a concern with opinel I think, it's them turning into nail breakers when wet. To really waterproof it you will need to take out the pin, bolster and blade before doing any of that thou, may not be worth the effort.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login