ZapWizard's Leatherman Free P4 Mods
-
@Dutch_Tooler said:
:DThat looks great!

-
8) I will be glad when I can carry my Charge or Wave again and get to use my Zap wizard sheath :ahhh -
great job on the blade adapter!
You kept the original file and removed the can opener.- I wonder if the original short file could be removed and the can opener kept on?
- Is there a mod where the P4 can be made wider so it can accomodate the new pieces without getting rid of the original ones?
-
@carl, if I may butt in:
- Can opener is .13" IIRC, file is either .07 or .06". Assuming you refer to the situation with the bit holder taking up all of the central position (between the springs) of the handle it sits in, you'd have to remove the file and something else, e.g. the ruler or awl, to make place for the can opener/Phillips in the opposite handle.
- Unlikely... the width is dependent on the studs in the plier head that slot into the handles when opened - widening the handles to accommodate more tools requires wider plier head stud placement, i.e. a new plier head. Note these are already different between P2 and P4. There has been speculation about a possible "P6" but this has failed to materialise until now.
Hope this helps.
-
@Dutch_Tooler said:
..... I'll probably end up assembling some kit in a small extra holster or pouch.Got me a small Skinth. Modded the bit cards a little bit to make them shorter so they fit in the Skinth's main compartment while the long bits go into the front pocket. The main compartment also hosts the saw and file blade in preparation for the eventual arrival of a T-shank blade holder. These blades will need to be shortened slightly, BTW, to fold inside the tool, I gather. There is more space for saw blades of all kinds, including diamond powder coated ones, if reasonably short or shortened to fit.



-
Like that set up

-
Thanks guys. It works alright... I just wish there was a more, eh, integrated manner ;)
-
Hope y’all had a good turkey day!
-
Had two great turkey days!

-
-
Found this thread while researching the P4! Ready to throw money at it and some accessories now :)
I’ve been using a Charge TTi, and I think the P4 will solve my gripes. But, I use the bit extender constantly. I work in IT, so their is a lot of appeal to choose the 4mm bit adapter, but I’d really need some sort of bit extender. Has anyone used a bit extender with this setup? Ideally if it could be stored inside the P4, that would be great. If not, perhaps externally like the leatherman bit extender?
This one looks interesting: https://www.wihatools.com/system-4-extension-blade-for-micro-bits Could he cut to size.
-
I got a similar extender at home, waiting for the 4mm bit holder to arrive. I will test and review the setup once I have everything in hand.
Regarding the "in tool" storage, I've been thinking for weeks for a way to store an extra 4mm bit in the frame since I couldn't find a double headed 4 mm bit on the web. No idea si far, so I doubt you could fit an extender in that puppy.
If anyone has any idea, I'm all ears.
-
Welcome to
schmobodia and Matpar 
-
Thanks Poncho, but you already gave me a welcome ;)
-
I try to make it a point to make everyone feel welcome :D I am just as glad to have you new guys here as the other members

-
Sorry for the delayed replies, I am sort of in Christmas/vacation mode. I have been working on the t-shank on and off a bit, I may have to look at adding some other stainless steel spring to make it work well. That means either a custom expensive part.
Don't forget about the Leatherman bit extender, it can be combined with my flat bit holder. I now recommend the flat bit holder over the 4mm, just due to the fact that you don't need to install magnets.
I also have a holder for both the P2 and P4 that has a grip for the bit extender built-in, as Dutch_Tooler shows above. -
@Matpar_McWolfie said:
I got a similar extender at home, waiting for the 4mm bit holder to arrive. I will test and review the setup once I have everything in hand.Regarding the "in tool" storage, I've been thinking for weeks for a way to store an extra 4mm bit in the frame since I couldn't find a double headed 4 mm bit on the web. No idea si far, so I doubt you could fit an extender in that puppy.
If anyone has any idea, I'm all ears.
I may go the flat it route. However, I have an old SwissArmy knife, that was “tech” oriented, and. Has double sided 4mm bits, not sure if you could find those for yourself.
Sent from my iPhone using Tapatalk
-
Received my 4mm bit holder and tabs for my P4 and installed everything. Looking good, although I had some issues with the print. The bit holder had the magnet compartment completely filled out with metal, so I had to re-drill it. Testing out the magnets, I ended up going through the magnet stop, but that was mainly because I used slightly weak magnets that needs direct contact with the bit to hold it tight. I glued the magnets in place so they don't move anyway. Plus, since they got deeper into the tool, I managed to cut another magnet to a third of it's length and add it to the stack, just to get a bit more power. If I end up shatter the magnets because of the contact with the bit, I can just replace them (bought a bunch on Ebay).
The other problem I had was the fact that the bits were a bit loose in the slot. That was more of a concern but I threw the bit holder in the vice with a bit inserted and squeezed it enough to bend it. The fit is better now. I'm a bit disappointed with Shapeways's consistency in their prints but hey, this is a custom part and I managed to fix the bugs. It also works well with the extender I had laying at home, which I might shorten (the thing is so long right now, see pictures).
I installed the tabs on the straight and the serrated blade with crazy glue, leaving the saw blade as is. I hit the tabs with rub n' buff of two different colors (bronze and silver) just to give the tool some "panache". The metallic look also makes it feel like the tabs are part of the P4, rather than being an add-on. Since there is so much texture on the tabs, it took the rub n' buff so well I'd be a fool to try and remove it.
You might notice I rearranged the tools on the pictures. I switched the straight and serrated blade to better serve the clumsy lefty that I am. Also, I installed the bit holder where the phillips screwdriver and the pry tool were, but I moved the pry tool to the other side and ditched the file and the ruler.
This is now a damn fine tool. I had to send it for repair though, before the mods (obviously). The pliers were binding the minute I was squeezing them ever so slightly. They replaced it and it now works like a charm! If you have the same problem, don't wait until you break in the tool, as I did. They know it's been an issue since release, and will fix it for you in no time.




Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
