Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

ZapWizard's Leatherman Free P4 Mods

Scheduled Pinned Locked Moved Leatherman Tools
513 Posts 1 Posters 158.5k Views
  1. Home
  2. Tool Talk
  3. Leatherman Tools
  4. ZapWizard's Leatherman Free P4 Mods
ZapWizard's Leatherman Free P4 Mods
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Dutch_Tooler Offline
    Dutch_Tooler
    Posts: 4,434
    Dutch_Tooler Offline
    Dutch_Tooler
    wrote on last edited by
    #225 Quote Reply

      @Dutch_Tooler said:
      ..... I'll probably end up assembling some kit in a small extra holster or pouch.

      Got me a small Skinth. Modded the bit cards a little bit to make them shorter so they fit in the Skinth's main compartment while the long bits go into the front pocket. The main compartment also hosts the saw and file blade in preparation for the eventual arrival of a T-shank blade holder. These blades will need to be shortened slightly, BTW, to fold inside the tool, I gather. There is more space for saw blades of all kinds, including diamond powder coated ones, if reasonably short or shortened to fit.

      10252019183021.jpg

      10252019183037.jpg

      10252019183047.jpg

      1 Reply Last reply
      • Rapidray Offline
        Rapidray
        Posts: 24,490
        Rapidray Offline
        Rapidray
        wrote on last edited by
        #226 Quote Reply

          Like that set up :cheers:

          1 Reply Last reply
          • Poncho65 Offline
            Poncho65
            Global Moderators
            Posts: 88,523
            Poncho65 Offline
            Poncho65
            Global Moderators
            wrote on last edited by
            #227 Quote Reply

              :iagree: :like:

              1 Reply Last reply
              • Dutch_Tooler Offline
                Dutch_Tooler
                Posts: 4,434
                Dutch_Tooler Offline
                Dutch_Tooler
                wrote on last edited by
                #228 Quote Reply

                  Thanks guys. It works alright... I just wish there was a more, eh, integrated manner ;)

                  1 Reply Last reply
                  • hbcorpse Offline
                    hbcorpse
                    Posts: 18
                    hbcorpse Offline
                    hbcorpse
                    wrote on last edited by
                    #229 Quote Reply

                      Hope y’all had a good turkey day!

                      1 Reply Last reply
                      • Rapidray Offline
                        Rapidray
                        Posts: 24,490
                        Rapidray Offline
                        Rapidray
                        wrote on last edited by
                        #230 Quote Reply

                          Had two great turkey days! :rofl:

                          1 Reply Last reply
                          • hbcorpse Offline
                            hbcorpse
                            Posts: 18
                            hbcorpse Offline
                            hbcorpse
                            wrote on last edited by
                            #231 Quote Reply

                              @Rapidray said:
                              Had two great turkey days! :rofl:

                              Ohhhh yeahhhhhhh!

                              For me, there’s nothing like a cold turkey sandwich the next day.

                              Plain white bread, lightly buttered with cold butter (something I picked up from my Grandpa), cold turkey slices, some cold gravy, and some cold cranberry sauce.

                              Hoo-wee!

                              1 Reply Last reply
                              • schmobodia Offline
                                schmobodia
                                Posts: 2
                                schmobodia Offline
                                schmobodia
                                wrote on last edited by
                                #232 Quote Reply

                                  Found this thread while researching the P4! Ready to throw money at it and some accessories now :)

                                  I’ve been using a Charge TTi, and I think the P4 will solve my gripes. But, I use the bit extender constantly. I work in IT, so their is a lot of appeal to choose the 4mm bit adapter, but I’d really need some sort of bit extender. Has anyone used a bit extender with this setup? Ideally if it could be stored inside the P4, that would be great. If not, perhaps externally like the leatherman bit extender?

                                  This one looks interesting: https://www.wihatools.com/system-4-extension-blade-for-micro-bits Could he cut to size.

                                  1 Reply Last reply
                                  • Matpar_McWolfie Offline
                                    Matpar_McWolfie
                                    Posts: 10
                                    Matpar_McWolfie Offline
                                    Matpar_McWolfie
                                    wrote on last edited by
                                    #233 Quote Reply

                                      I got a similar extender at home, waiting for the 4mm bit holder to arrive. I will test and review the setup once I have everything in hand.

                                      Regarding the "in tool" storage, I've been thinking for weeks for a way to store an extra 4mm bit in the frame since I couldn't find a double headed 4 mm bit on the web. No idea si far, so I doubt you could fit an extender in that puppy.

                                      If anyone has any idea, I'm all ears.

                                      1 Reply Last reply
                                      • Poncho65 Offline
                                        Poncho65
                                        Global Moderators
                                        Posts: 88,523
                                        Poncho65 Offline
                                        Poncho65
                                        Global Moderators
                                        wrote on last edited by
                                        #234 Quote Reply

                                          Welcome to :MTO: schmobodia and Matpar :cheers:

                                          1 Reply Last reply
                                          • Matpar_McWolfie Offline
                                            Matpar_McWolfie
                                            Posts: 10
                                            Matpar_McWolfie Offline
                                            Matpar_McWolfie
                                            wrote on last edited by
                                            #235 Quote Reply

                                              Thanks Poncho, but you already gave me a welcome ;)

                                              1 Reply Last reply
                                              • Poncho65 Offline
                                                Poncho65
                                                Global Moderators
                                                Posts: 88,523
                                                Poncho65 Offline
                                                Poncho65
                                                Global Moderators
                                                wrote on last edited by
                                                #236 Quote Reply

                                                  I try to make it a point to make everyone feel welcome :D I am just as glad to have you new guys here as the other members :tu: :like:

                                                  1 Reply Last reply
                                                  • ZapWizard Offline
                                                    ZapWizard
                                                    Posts: 171
                                                    ZapWizard Offline
                                                    ZapWizard
                                                    wrote on last edited by
                                                    #237 Quote Reply

                                                      Sorry for the delayed replies, I am sort of in Christmas/vacation mode. I have been working on the t-shank on and off a bit, I may have to look at adding some other stainless steel spring to make it work well. That means either a custom expensive part.

                                                      Don't forget about the Leatherman bit extender, it can be combined with my flat bit holder. I now recommend the flat bit holder over the 4mm, just due to the fact that you don't need to install magnets.
                                                      I also have a holder for both the P2 and P4 that has a grip for the bit extender built-in, as Dutch_Tooler shows above.

                                                      1 Reply Last reply
                                                      • schmobodia Offline
                                                        schmobodia
                                                        Posts: 2
                                                        schmobodia Offline
                                                        schmobodia
                                                        wrote on last edited by
                                                        #238 Quote Reply

                                                          @Matpar_McWolfie said:
                                                          I got a similar extender at home, waiting for the 4mm bit holder to arrive. I will test and review the setup once I have everything in hand.

                                                          Regarding the "in tool" storage, I've been thinking for weeks for a way to store an extra 4mm bit in the frame since I couldn't find a double headed 4 mm bit on the web. No idea si far, so I doubt you could fit an extender in that puppy.

                                                          If anyone has any idea, I'm all ears.

                                                          I may go the flat it route. However, I have an old SwissArmy knife, that was “tech” oriented, and. Has double sided 4mm bits, not sure if you could find those for yourself.

                                                          Sent from my iPhone using Tapatalk

                                                          1 Reply Last reply
                                                          • Matpar_McWolfie Offline
                                                            Matpar_McWolfie
                                                            Posts: 10
                                                            Matpar_McWolfie Offline
                                                            Matpar_McWolfie
                                                            wrote on last edited by Matpar_McWolfie
                                                            #239 Quote Reply

                                                              Received my 4mm bit holder and tabs for my P4 and installed everything. Looking good, although I had some issues with the print. The bit holder had the magnet compartment completely filled out with metal, so I had to re-drill it. Testing out the magnets, I ended up going through the magnet stop, but that was mainly because I used slightly weak magnets that needs direct contact with the bit to hold it tight. I glued the magnets in place so they don't move anyway. Plus, since they got deeper into the tool, I managed to cut another magnet to a third of it's length and add it to the stack, just to get a bit more power. If I end up shatter the magnets because of the contact with the bit, I can just replace them (bought a bunch on Ebay).

                                                              The other problem I had was the fact that the bits were a bit loose in the slot. That was more of a concern but I threw the bit holder in the vice with a bit inserted and squeezed it enough to bend it. The fit is better now. I'm a bit disappointed with Shapeways's consistency in their prints but hey, this is a custom part and I managed to fix the bugs. It also works well with the extender I had laying at home, which I might shorten (the thing is so long right now, see pictures).

                                                              I installed the tabs on the straight and the serrated blade with crazy glue, leaving the saw blade as is. I hit the tabs with rub n' buff of two different colors (bronze and silver) just to give the tool some "panache". The metallic look also makes it feel like the tabs are part of the P4, rather than being an add-on. Since there is so much texture on the tabs, it took the rub n' buff so well I'd be a fool to try and remove it.

                                                              You might notice I rearranged the tools on the pictures. I switched the straight and serrated blade to better serve the clumsy lefty that I am. Also, I installed the bit holder where the phillips screwdriver and the pry tool were, but I moved the pry tool to the other side and ditched the file and the ruler.

                                                              This is now a damn fine tool. I had to send it for repair though, before the mods (obviously). The pliers were binding the minute I was squeezing them ever so slightly. They replaced it and it now works like a charm! If you have the same problem, don't wait until you break in the tool, as I did. They know it's been an issue since release, and will fix it for you in no time.

                                                              IMG_20191217_234331.jpg

                                                              IMG_20191217_234252.jpg

                                                              IMG_20191217_234218.jpg

                                                              IMG_20191218_010011.jpg

                                                              1 Reply Last reply
                                                              • Wspeed Offline
                                                                Wspeed
                                                                Posts: 76,225
                                                                Wspeed Offline
                                                                Wspeed
                                                                wrote on last edited by
                                                                #240 Quote Reply

                                                                  Looking good :like: :tu:

                                                                  1 Reply Last reply
                                                                  • ZapWizard Offline
                                                                    ZapWizard
                                                                    Posts: 171
                                                                    ZapWizard Offline
                                                                    ZapWizard
                                                                    wrote on last edited by
                                                                    #241 Quote Reply

                                                                      @Matpar_McWolfie said:
                                                                      Received my 4mm bit holder and tabs for my P4 and installed everything. Looking good, although I had some issues with the print.

                                                                      Glad you were able to get the issues fixed. I have had about four folks get the 4mm with the middle hole filled, even with a special note on my build for their post-processing folks to ensure it is clear.
                                                                      Tolerances are always a bitch. Some 4mm bits aren't 4mm, sometimes they bake the part a bit longer and it comes out too small. I have to error on the side of a bit too large to ensure people don't get completely unusable parts.
                                                                      The flat bit holder is just simpler, so it is what I am recommending to folks, but on YouTube the 4mm has about 100x the number of views. But right now its about a 50% split on which one folks chose.

                                                                      Rub and buff looks good. If you want a high chrome finish the secret is to use a Molotow Liquid Chrome Marker. They work great on the nylon.

                                                                      1 Reply Last reply
                                                                      • Matpar_McWolfie Offline
                                                                        Matpar_McWolfie
                                                                        Posts: 10
                                                                        Matpar_McWolfie Offline
                                                                        Matpar_McWolfie
                                                                        wrote on last edited by
                                                                        #242 Quote Reply

                                                                          @ZapWizard said:
                                                                          Glad you were able to get the issues fixed. I have had about four folks get the 4mm with the middle hole filled, even with a special note on my build for their post-processing folks to ensure it is clear.
                                                                          Tolerances are always a bitch. Some 4mm bits aren't 4mm, sometimes they bake the part a bit longer and it comes out too small. I have to error on the side of a bit too large to ensure people don't get completely unusable parts.
                                                                          The flat bit holder is just simpler, so it is what I am recommending to folks, but on YouTube the 4mm has about 100x the number of views. But right now its about a 50% split on which one folks chose.

                                                                          Rub and buff looks good. If you want a high chrome finish the secret is to use a Molotow Liquid Chrome Marker. They work great on the nylon.

                                                                          Oh yeah I heard about Molotow. Great stuff. I saw Adam Savage use the refill with an air brush on Youtube. You couldn't tell the difference with polished aluminium.

                                                                          For the bit holder, the bottle opener kept me from switching to the flat bit version, although it was a close call. But I cut myself way too many times prying out a cap with a lighter and having the whole bottle neck come off completely. Also, the 4mm allows me to have tiny screwdrivers, as the one on the Charge TTI, which I used on a daily basis before buying the P4.

                                                                          As for the printing issues, I can't really complain. the design is awesome, and the issues I had were in no way major. As you mentionned, 4 mm bits aren't always 4 mm. Mine are sitting at 3.95 mm, where the bit holder had a 4.2 mm opening, "pre-squeezing".

                                                                          All in all, I have an awesome tool by my side at any time, thanks to you! Can't wait to see your progress on the blade holder.

                                                                          1 Reply Last reply
                                                                          • Poncho65 Offline
                                                                            Poncho65
                                                                            Global Moderators
                                                                            Posts: 88,523
                                                                            Poncho65 Offline
                                                                            Poncho65
                                                                            Global Moderators
                                                                            wrote on last edited by
                                                                            #243 Quote Reply

                                                                              Glad to see that this design has come to fruition and that peeps are getting use out of it :salute: :like:

                                                                              1 Reply Last reply
                                                                              • hbcorpse Offline
                                                                                hbcorpse
                                                                                Posts: 18
                                                                                hbcorpse Offline
                                                                                hbcorpse
                                                                                wrote on last edited by
                                                                                #244 Quote Reply

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  • 10
                                                                                  • 11
                                                                                  • 12
                                                                                  • 13
                                                                                  • 14
                                                                                  • 25
                                                                                  • 26
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. Leatherman Tools
                                                                                  4. ZapWizard's Leatherman Free P4 Mods
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0