Can Opener Comparison
-
Roxon Storm S801 S

This is the updated version of the original Storm. The can opener is now positioned properly, in addition to being sharpened. And it shows. It punched through extremely easily. It lost a point to comfort due to the ruler's 90° edge. It never jammed or slipped off the rim, not even once. It also had to lose a point because, while tracing around the rim is consistent and easy, it leaves behind a sharp edge.
In the original the can opener was too deep in the handle to engage properly on the can's lid. It is therefore unclear whether they imagined the can opener moving forwards, like a quarter-circle, or backwards, like a claw. Seeing how the cutting edge faces forwards, one would think that it would operate like a quarter-circle. It can, but it was much easier to go backwards on the lid.
It is nice to see that Roxon listened to feedback and fixed the can opener. Despite the ruler's edge and the sharp edges you will leave behind, it opens cans just as fast as the best can openers, creates no shrapnel, does not push the lid inwards, and does not slip or jam. Not a bad choice at all, which is good, when you take into account that the tool also has a great cap lifter and corkscrew with leverage arm.
2 points for punching through.
1 for comfort.
2 for not jamming.
1 for cutting.
2 for not slipping.
Total: 8 -
Funky looking can opener

-
Funky and functional.

-
Bibury 21 in 1

A locking quarter-circle, properly positioned to hook on the rim.
Initial piercing was extremely easy. Comfort took a small hit, due to some sharp edges, but nothing we have not seen even with premium multi-tools.
The slotted screwdriver tip acted as a stop, preventing the can opener from sinking in too deep in the lid. As the cutting edge made a cut, the screwdriver tip will meet the lid, signifying that the cutting edge has ran out and it is time to advance to the next cut. This unintentional feature lends itself to cutting consistently, every cut being equal in length.While tracing around the lid is easy, sometimes the rim will bend and you will not be able to continue on a previous cut. It was necessary to pierce ahead and then connect the two cuts. Nothing time consuming or difficult, just an extra little step to get the can opened, if you happen to bend the rim.
The lid was not pushed in the can, and it did not create any shrapnel. Some sharp points were left behind, but otherwise a quick, easy job, with some minor discomfort, no slipping and no jamming. Not a bad choice at all, which is refreshing to see in a budget multi-tool that went with the quarter-circle.

2 points for punching through.
1 for comfort.
2 for not jamming.
1 for cutting.
2 for not slipping.
Total: 8 -
The Bibury multi-tool's can opener did even better when we take into account the promotional photos.

-
Nice work RP

-
@ReamerPunch said:
So now that Leatherman has a quarter-circle, all big four brands have a quarter-circle.
I do not know how I feel about this.
The standard LM claw is excellent, why did they go with the quarter-circle for the Free series?
Interesting - and the cap lifter is on the Phillips. The combo cap lifter can opener on the Wave was adequate for both, but great for neither application when I used it extensively several years ago.
Maybe the change is because people use the cap lifter more often than the can opener, so they wanted a better design on that? There's an AMA on another thread, or Reddit, with the Leatherman engineers. It might be worth an ask.
I always root for the claw for opening cans, even though I have used a SAK with a quarter circle every time in the last decade for this task. I find it easier to pull than to push, and find myself cutting around a can in sections just to be able to pull in a clockwise direction with the SAK.
-
If only there was some way you could get your hands on this ...

-
@ElevenBlade said:
Interesting - and the cap lifter is on the Phillips. The combo cap lifter can opener on the Wave was adequate for both, but great for neither application when I used it extensively several years ago.Welcome to the forum!

But I will have to disagree. The Wave has a great combo opener. For cans, it is the best I have used. No learning curve. Perfect shape and execution to open a can, with no sharp edges left behind. Give it to someone who has never used a multi-tool or SAK can opener. They'll open it perfectly. Give them a SAK and watch them struggle. The locking Leatherman claw is a flawless design for can openers. You can open cans blindfolded and still get perfect results.
For bottles, it works. It is not perfect, but if you place it correctly and open the bottle in a controlled motion, you won't pierce the cap and get it off the bottle in one motion. -
@ElevenBlade said:
If only there was some way you could get your hands on this ...I love a good claw.

-
Bibury 31 in 1/Grand Harvest GHK2
Right-handed0 points.
Yet again, the can opener is placed too far right in the handle for it to function properly.
This would definitely work well if it swapped positions with the serrated rescue blade.
What a pity.

-
Reason I wanted a Swiss-type push can opener was that 1 it was easier to open, and 2 that when opening cheaper can they do not leave splinters behind like can and will happen with a normal can opener like in a common Leatherman multitool. Metal splinter hurt, can fester, and take a week or better to remove. Never once had splinter issues with a Swiss-type push can opener.
Took Leatherman many decades to make a push can opener that is on some of their Free series. Have you tested one of those yet? Will have to reverse browse to see. Though the rest of the tool I'm not sold on. Magnets? Really??
Miss the Flair I had. While it was not the best can opener when compared for speed, it did make a clean cut and nary a splinter left behind. I do miss it. It however lacked a file. Keep hoping it will show up. No idea where it went walkabout at. Came home and it was missing from the sheath. :'(
-
Looks like a lot of companies don’t
test the tools they put on them ???
If they did they would of known that
they can opener is in the wrong place
-
@ReamerPunch said:
So now that Leatherman has a quarter-circle, all big four brands have a quarter-circle.
I do not know how I feel about this.
The standard LM claw is excellent, why did they go with the quarter-circle for the Free series?
Not so excellent on cheaper quality cans. They leave splinters behind on the outer areas of the can where one uses their hands for gripping. Fruit cans seems to be the worst, from no-name to basic bargain brands.
Have you tried one of them old fogy type can openers that go from the side? Do not recall seeing anyone actually posting photos or a video of them being used.

-
@ReamerPunch said:
Bibury 31 in 1/Grand Harvest GHK2
Right-handed0 points.
Yet again, the can opener is placed too far right in the handle for it to function properly.
This would definitely work well if it swapped positions with the serrated rescue blade.
What a pity.

perhaps you could send a friendly email to the company with those pictures - thats a very basic design flaw they should have considered. -
@ElevenBlade said:
perhaps you could send a friendly email to the company with those pictures - thats a very basic design flaw they should have considered.if I were to send an email with every flaw of that multi-tool, the text would be two pages long.

-
@ReamerPunch said:
if I were to send an email with every flaw of that multi-tool, the text would be two pages long.

-
@ReamerPunch said:
if I were to send an email with every flaw of that multi-tool, the text would be two pages long.
Maybe more than two pages. Full review:
Grand Harvest GHK2 -
Grand Harvest GHK2/Bibury 13 in 1
Left-handed0 points.
The can opener is still too far deep in the handle to hook onto the rim. It is marginally better than right-handed, as it will barely hook onto, instead of not hooking on at all.
As awkward as it is for a right-handed person to try and use this abomination left-handed, it does not stop there. As it barely hooks onto the rim, the cutting orientation is thrown off.
Initial piercing is comically bad. First you have to get the can opener to hook and find a proper spot to pierce, which is itself tedious. Actually punching through is not easy, despite having a decently sharpened edge. The cutting angle will be off, the ergonomics are bad, it is left-handed, it can slip off at any minute, and it is not piercing as close to the rim as possible. Everything combined to make the first cut a very frustrating experience.Advancing from one cut to the next is also not easy. All issues present in the initial cut will apply to all cuts. Due to the force required to keep the can opener in place, so it does not slip, the rim may bend inwards, interfering even more with the cutting orientation. After the second or third cut, it was impossible to continue on the same route. I had to start with a new initial piercing.
If you have the time, patience, and like pain or have gloves on, you could actually open the can. The cutting edge is sharp and will not create shrapnel.
Using this was interesting. The shape is fine, the edge is actually sharpened, and the hook is also well shaped to theoretically grab onto the rim. As good as it looks, it is yet another example of companies just going with a shape that seems it would work, but not actually using it to see if it it will work.


-
This is the same exact issue the Roxon Storm had (and not the only similarity they share. More on that later).
Spoiler:
@ReamerPunch said:
Roxon Storm
Out of the box, the can opener was unable to hook onto the rim. Ergonomics, sharpness, ease of use, nothing matters. You will only be able to open ring-pull cans with this. If it's a classic can, this is not the answer.0 points.

Roxon Storm (modded)
I swapped places of the can opener and cord cutter. The can opener is now functional, though pretty average.0 points for punching through. Not easy, as the piercing point is quite blunt.
1 for comfort. Stayed in hand, did not hurt enough to stop. Scale edge still dug into my hand.
2 for not jamming.
1 for cutting. It could have a sharper edge with more of an angle to it. Consistent cut, though it left jagged, sharp edges.
2 for not slipping. The hook is at least better designed than the rest of it, and it stayed on the can rim.
Total: 6

Same problem, although the GHK2 can opener is sharpened.
Same solution: swap the can opener and serrated blade positions, to bring the can opener next to the blade, closer to the edge of the handle, so that it will hook onto the rim right-handed.
However, this mod is not easy.
First of all, the backsprings are amazingly strong. Even if you mod the can opener to go next to the blade, it will not unfold easily. When I tried to unfold it with my finger-nail, my finger-nail split in two, while the can opener remained folded, probably laughing at me.Also, the mod itself is not as easy as it was with the Roxon Storm. The main issue with the mod is that you cannot just unscrew the handle, take out the implements, and put them back in the order you want. The backsprings will be in the way, and you will have to push them back to make room for the implements to drop in.
This was quite easy to do with the Storm. I put it in a vise, with a bolt pushing back the backsprings, and dropped the implements in place, with the can opener where it was supposed to be. And the backsprings are pushed back, but are not flush with the handle on the other side. When they were pushed back, they did not contact the side of the handle that the vise was against.
With the GHK2, the herculean backsprings will be more of a problem, and they are flush with the handle. You can not just put it in a vise and push the backsprings back with a bolt. The bolt will not push against a straight surface either, because these backsprings are angled. Quite a tedious set-up. I will post pictures to illustrate exactly what I am talking about.
I may try this again in the future, just to make the can opener functional, and because I am curious to see how good it will actually be. Probably quite good, since the shape, edge, and hook are ok.
But even then, deploying the can opener requires metallic assistance. Why bother?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login