ZapWizard's Leatherman Free P4 Mods
-
First of all. I really like your mods and will probably end up buying a lot of them. Especially looking forward to be able to use the diamond coated file with the P4.
When I found this thread I started to dig thru some older Leatherman stuff and found this.
Still works very well.
-
@Foozebar said:
First of all. I really like your mods and will probably end up buying a lot of them. Especially looking forward to be able to use the diamond coated file with the P4.When I found this thread I started to dig thru some older Leatherman stuff and found this.
Still works very well.Great post and photos!

-

Now for being able to finally lay my hands on a Universal Tool Adapter over here. Rarer than hens' teeth... ::)
-
Welcome to
fooze 
I also have found it difficult to find the Universal Adapter here in the States as well :ahhh
Hopefully we can both find one, DT 
-
Howdy Folks. It is Shapeways delivery day. :woohoo:
I received the thumb tabs for the FREE T2 & T4, as well as the Surge. Both are products folks have requested here, as well as on YouTube.
I also had to order a new Surge holster as the design needed to be updated to fit the tabs.
All the parts came out great, no changes required.I recorded a few sets of videos for these, but for some reason they both had no audio. ??? Which sucked as I super-glued the thumb tabs into place. :think:
So this forced me to put up to shut up, and actually go though the super-glue removal processes I recommend but haven't tested on these actual parts.And then.....my video of the glue removal process was "recorded' during a time where I forgot to actually press the record button. :facepalm:
So tomorrow I will re-record that video tomorrow. The good news is the removal process worked. -
Hello again.
Not my intent to highjack this thread, but I'm not allowed to send PM's yet.
How about an updated version of the removable bit driver..?
Here's the old one flanked by my trusty old workhorse.
A 1:st gen Surge with tools from a Core.Such an adapter might fit all the Free models (P, T & K) and not void any warranties. :D
-
@ZapWizard said:
Howdy Folks. It is Shapeways delivery day.
I received the thumb tabs for the FREE T2 & T4, as well as the Surge. Both are products folks have requested here, as well as on YouTube.
I also had to order a new Surge holster as the design needed to be updated to fit the tabs.
All the parts came out great, no changes required.I recorded a few sets of videos for these, but for some reason they both had no audio. ??? Which sucked as I super-glued the thumb tabs into place.

So this forced me to put up to shut up, and actually go though the super-glue removal processes I recommend but haven't tested on these actual parts.And then.....my video of the glue removal process was "recorded' during a time where I forgot to actually press the record button.

So tomorrow I will re-record that video tomorrow. The good news is the removal process worked.Nice

-
Not my intent to highjack this thread, but I'm not allowed to send PM's yet.
How about an updated version of the removable bit driver..?
Here's the old one flanked by my trusty old workhorse.
A 1:st gen Surge with tools from a Core.Such an adapter might fit all the Free models (P, T & K) and not void any warranties. :D
Nice Surge

-
@Foozebar said:
How about an updated version of the removable bit driver..?
Such an adapter might fit all the Free models (P, T & K) and not void any warranties. :DThis was actually my first idea for the FREE series. I even ordered that bit adapter to see if it would work on the FREE Philips driver with an easy mod or shims.
I haven't revisited the idea though, I will take another look. The catch though is that they use a spring clip or a spring-loaded ball (I forget which) as a retainer for the bits. I could use magnets to retain the bits, or some side grips like the flat bit holder. -
Now for being able to finally lay my hands on a Universal Tool Adapter over here. Rarer than hens' teeth... ::)
@Poncho65 said:
Welcome to
fooze 
I also have found it difficult to find the Universal Adapter here in the States as well :ahhh
Hopefully we can both find one, DT 
I don’t mean to sound condescending, but have y’all checked eBay?
I just popped over to search “Leatherman universal tool adapter” and boom.
Lots of listings.
Some even come with a cool case, a leather holster, and even a Leatherman multitool!!!
The variety is mixed, but I’ve seen some listed with SuperTools, Waves, Rebars, Surges, etc...and some are vintage models!
Anywho...worth a shot!
Many of them seemed to be in the US, but I caught one or two that had €Euros listed as the currency...
-
The problem with ebay auctions in the US is that the ebay policy tends to exclude shipping to Europe for anything to do with multitools and knives...
-
@hbcorpse said:
I don’t mean to sound condescending, but have y’all checked eBay?I just popped over to search “Leatherman universal tool adapter” and boom.
Lots of listings.
Some even come with a cool case, a leather holster, and even a Leatherman multitool!!!
The variety is mixed, but I’ve seen some listed with SuperTools, Waves, Rebars, Surges, etc...and some are vintage models!
Anywho...worth a shot!
Many of them seemed to be in the US, but I caught one or two that had €Euros listed as the currency...
I guess I should correct my statement
I find it difficult to find one for the price I am willing or able to pay
:D Lots of time they say universal and end up being the standard adapter as well 
-
@Poncho65 said:
I guess I should correct my statement
I find it difficult to find one for the price I am willing or able to pay
:D Lots of time they say universal and end up being the standard adapter as well 
Wait...there’s a “standard” adapter, as well as a universal adapter?
I just bought one on eBay...hope it arrives.





I also hope, that this is the one that will fit my Free P4...as pictured above!
-
Very nice...I think I saw 2 on the eBay - one kinda affordable and the other was at $100 IIRC
Your’s looks great!
-
-
For the third time I recorded a video on how to remove the glued thumb tabs. This time I tested the audio with a test clip, but it still cut out after about a minute. I'll figure out why somehow.
So this is my first crack at trying to narrate, which I hate doing.The good news is that I have validated three times over that both the acetone and heat-gun methods work at removing super-glued thumb tabs from the blades. Other than a bit of color loss on the acetone method, there is no damage to the actual thumb tabs. If you were fearful of gluing something to your precious multitool, don't worry.
-
-
@SteveC said:
Yours is the original adapter not the universal one.@Poncho65 said:
The Universal is one that I can never find for a decent price
but I have 2 of the Standard one
:DHang on...so what’s the difference, other than in name (obviously)...?
The Universal’s name seems self explanatory...
But what is the Standard?
That’s the one I bought?
I’m guessing it will only fit specific models?
———————————
EDIT:
Ok, I’ve done quite a bit of web-sleuthing since I posted this.I’ve found that the one I bought on eBay is the Original/Standard.
So...that one Universal model on eBay?
Should be here in the next two weeks.
I couldn’t help myself.
I DID find a good picture of an OG adapter that someone had modified to “work” universally, but did not watch the YouTube video it came from.

So, now, it seems I’ll have one of each.
I’m hoping the Universal one will fit in the caddy of the OG one...I’d really like to carry it in that caddy.
Anyway...just figured I’d edit/update my earlier post (which probably wasn’t even seen by many, if any).
Thanks a lot, to the group.
Y’all have had me spending more money on stuff than I ever planned on!
-
Not my intent to highjack this thread, but I'm not allowed to send PM's yet.
How about an updated version of the removable bit driver..?
Here's the old one flanked by my trusty old workhorse.
A 1:st gen Surge with tools from a Core.Such an adapter might fit all the Free models (P, T & K) and not void any warranties. :D
@ZapWizard said:
This was actually my first idea for the FREE series. I even ordered that bit adapter to see if it would work on the FREE Philips driver with an easy mod or shims.
I haven't revisited the idea though, I will take another look. The catch though is that they use a spring clip or a spring-loaded ball (I forget which) as a retainer for the bits. I could use magnets to retain the bits, or some side grips like the flat bit holder.I came across this picture...says it’s a 1/4” socket, and is friction fit on there, with the Phillips head and Prybar tools in use.
No further info.

Thanks Reddit!
Seems like a good work-around.
-
@hbcorpse said:
Hang on...so what’s the difference, other than in name (obviously)...?The Universal’s name seems self explanatory...
But what is the Standard?
That’s the one I bought?
I’m guessing it will only fit specific models?
———————————
EDIT:
Ok, I’ve done quite a bit of web-sleuthing since I posted this.I’ve found that the one I bought on eBay is the Original/Standard.
So...that one Universal model on eBay?
Should be here in the next two weeks.
I couldn’t help myself.
I DID find a good picture of an OG adapter that someone had modified to “work” universally, but did not watch the YouTube video it came from.

So, now, it seems I’ll have one of each.
I’m hoping the Universal one will fit in the caddy of the OG one...I’d really like to carry it in that caddy.
Anyway...just figured I’d edit/update my earlier post (which probably wasn’t even seen by many, if any).
Thanks a lot, to the group.
Y’all have had me spending more money on stuff than I ever planned on!
Yep that little tab is about the main difference that I can find with the 2 different models (and I guess those 2 rivets as well
)
Glad we can help you spend your money

Excited for you that you have a Universal one on the way

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login