BO Charge Titanium Handle Help!
-
pics?
-
::)
I don't take pics! :D
Anyways, the Rustoleum enamel paint looked great but it was very sticky even after it dried... So, I sprayed it down with some spraypaint and I'm waiting for it to dry.. The spray paint should work. I will carry this tool a lot, and well see how the finish holds up!
-
The handles aren't BO, they are more of a paint.
I remember reading some where that BO won't work on Ti so it's something else that is on the BO Charge handles. I also remember reading that they are prone to chipping and/or flaking.
BO only works on titanium and aluminum. They are the only metals that oxidize, so all the other "BO" tools are coated with something instead.
Def
-
Well this totally sucks! After it all dried I ran my nail across it and it left a huge scratch! So, I used turpentine or similar to remove all the paint and now I am back to square one! :) Any suggestions at all?
I may see if I could Duracoat it!
-
wonder if you could use that do it yourself bed liner in a light coat on it? of course it could really mess up a Charge
-
Hmm, I may go to autozone and pick up one of those touch up kits and do it that way. What's the worst that could happen?
-
does that stuff come off with acetone just in case?
-
@Leatherman123 said:
Well this totally sucks! After it all dried I ran my nail across it and it left a huge scratch! So, I used turpentine or similar to remove all the paint and now I am back to square one! :) Any suggestions at all?I may see if I could Duracoat it!
Duracoat it!!!
Then again the price.....
-
@Grant Lamontagne said:
The handles aren't BO, they are more of a paint.
I remember reading some where that BO won't work on Ti so it's something else that is on the BO Charge handles. I also remember reading that they are prone to chipping and/or flaking.
BO only works on titanium and aluminum. They are the only metals that oxidize, so all the other "BO" tools are coated with something instead.
Def
You missed my post earlier on this. You've got it backwards. ;)
Oxidizing=Steel
Anodizing=Al/Ti other Metalshttp://en.wikipedia.org/wiki/Bluing_(steel)
http://en.wikipedia.org/wiki/Anodizing -
Spoon, your not going to try and cover up the spots on your BO Ti?
-
Nah.
They never really bothered me and I kind of like the wear. Really makes it mine.
-
@Grant Lamontagne said:
The handles aren't BO, they are more of a paint.
I remember reading some where that BO won't work on Ti so it's something else that is on the BO Charge handles. I also remember reading that they are prone to chipping and/or flaking.
BO only works on titanium and aluminum. They are the only metals that oxidize, so all the other "BO" tools are coated with something instead.
Def
You missed my post earlier on this. You've got it backwards. ;)
Oxidizing=Steel
Anodizing=Al/Ti other Metalshttp://en.wikipedia.org/wiki/Bluing_(steel)
http://en.wikipedia.org/wiki/AnodizingWhoops... :D
Def
-
@Spoonrobot said:
Nah.They never really bothered me and I kind of like the wear. Really makes it mine.
True, what if it did bother you? What would you do? :D
-
ask an expert. perhaps autobody guy? might be able to give you a tip on an adhering paint? if no luck give tool to a bud and buy a new one.
-
I'd strip the old finish off and then flame anodize them. :D
Failing that a bake-on coating like Dura-Coat or Aluma-Hyde would probably work the best. It's spendy though, guy that does skulls and stuff with Dura-Coat on RAT knives quoted me $55 to do a set of Kick handles.
-
Oxidizing=Steel
Anodizing=Al/Ti other Metalshttp://en.wikipedia.org/wiki/Bluing_(steel)
http://en.wikipedia.org/wiki/AnodizingI thought it was Spoonrobots post that I was thinking about but I wasn't 100% sure.
LM123 use this Charge on all your really dirty MT tasks that way it won't bother you if it gets worse -
If you're going to paint it... don't use enamel..
the reason that you could easily scratch it after coating it a second time was that the enamel didn't cure. (enamels take at least 3 months to fully cure, normally closer to a year in decent temp.)
I suggest using lacquer or urethane paints to patch up.
As I'm not sure what they used to mock the BO on the titanium handles I won't suggest what to use to remove the previous paint you used.If you're wanting a perfect surface, I would suggest striping all the mock BO, prime (you will have to find a metal primer that can bite into ti), then have it coated by someone good with an airbrush using urethane paints (same stuff they use on real cars). Like Sean suggested an auto body shop may be the best choice.
Plastic modeler for 10 years,
Steve
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login






