New guy with a bit extender problem/question...
-
This sounds like a warranty issue. You could email LM.
-
I wondered about that... See I've got a BMW motorcycle and "They all do that" is a normal reply to odd things that they do.
The fact that I have two bit extenders from totally seprate warehouses that exhibit the same thing makes me think that is just how they are.
I figured that if anyone had them that looked different, they'd chime in by now.
I'm still liking this thing very much. Made myself a chisel today based on a post here that shows how to make one from a spade bit.
Gotta love tinkering in the garage.
-
Just got the extender in the post this morning, bit got stuck immediately and couldnt remove it even with wiggling and pliers. managed to get it out by holding the bit in vice and pulling on the extender itself with some swearing and wobbling. Put a little grease in there and tried again but didnt help secnd time was just as bad.
The ring in mine spun freely (uk stock) so my thought was to stretch the spring to push itself hard against the outer in the hope it would then have less grab on the bits. After 30min trying different approaches and the spring in and out a few times but with no real benefit.
Ive now removed the ring/spring entirely and dropped a 2mm x 6mm N52 magnet in the bottom which seem perfectly adequate for holding even the smallest LM flat bit and actually brilliant better for standard bits as they now sit higher. I was going to glue it in but so far its stayed in place just by a little friction against the sides and the magnetism.
Obviously this ring idea is a bit smurf ??? anyway apart from feeling like a mug paying £25 / $30 it looks and works great now, cant help feeling id have been better off just filing down a standard extension for 1/4 of the price and probably the same amount of time i spent messing about with the official one!!

-
That’s not good at all.

-
Thats weird problem, i dont have any problems with my extender, i can move bits easily from extender and put them there.
Only Tools Matters
-
Thats a bummer :(. You can always mod your own bit extender
. Just use a bit to determine how much material you want off a random extender you might have or one you can get reasonably cheap. Grind away needed material and fit into bit holder. I've made a few and they work great. Add magnet if needed or mod one that already has magnet
. -
Mine is also new, but works smoothly
I took a look into the holder, and the ring does have roughly 4mm of overlap, I can barely feel the bits lock in, and they release smoothly -
Great thread necro though.

-
We don't mind necro threads here on MTo ;)
-
I've had the exact same problem on the first extender I've bought some years ago for my Wave.
I took the ring out, cut off the overlap part and put it back. No problems since
-
Bought mine the other day. As soon as I put it in it got stuck immediately. Found this forum and saw that everyone else has had the same exact issue.
After reading through and hearing how much people were struggling to pry it out. Now this of course will only work if you have a brazing torch. Took my torch heated up the end till it was bright red and was able to remove it easily. Pretty insane that this is what Hass to be done to do it without any swearing or too much headache but going to remove the ring that binds the bit inside and put a magnet in the bottom which one of the other uses recommended. -
Welcome to
tgasbarro
Hope that the fix works out for you 
-
BOTH of the two extenders I have had lock in bits..ESPECIALLY normal hex bits. I may just add a magnet like others have done..
-
A less ostentatious way is: using a regular hex bit (Preferably a long one) placed in a vise with point down, insert extender; use a medium/large flat blade screwdriver to pry out extender, repeat until split ring stretches and holds bits with enough pressure and/or to your liking; it worked for me (repeated cycle X3 times), and does not affect the tool's tempering.

-
@Juan el Boricua said:
A less ostentatious way is: using a regular hex bit (Preferably a long one) placed in a vise with point down, insert extender; use a medium/large flat blade screwdriver to pry out extender, repeat until split ring stretches and holds bits with enough pressure and/or to your liking; it worked for me (repeated cycle X3 times), and does not affect the tool's tempering.
This is awesome ! why is there no way to save specific posts like this for later reference :'(
-
@Happy Gilmore said:
This is awesome ! why is there no way to save specific posts like this for later reference :'(Bookmark top of page works
-
@McStitchy said:
I've had the exact same problem on the first extender I've bought some years ago for my Wave.
I took the ring out, cut off the overlap part and put it back. No problems since
Not sure of anybody understood what I wrote to this a while ago. In my case the problem happened only at the party where the ring overlaps (has two layers). If I insert the bit in a way that it is held where the ring doesn't overlap then all was fine.
I did take the ring out and shortened/cut off the overlap part anyways.Regarding the magnet idea I think it will not work well with LM flat bits as they have a driver profile on both ends, so there is less material to be attracted by the magnet.
-
This thread really helped me. I took the wooden jaws off my bench vise and removed the stuck leatherman bit. Then, I removed the retention ring (using a tiny flathead screwdriver) and cut off the overlapping piece with am the wire cutter on the inside of the pliers. I put the ring back in (now no overlap) and it works perfectly. The bits stay in even when you shake the extender hard, and they are easy to remove with fingers. I would have never thought to do all of this if it weren’t for you folks. Thanks so much!!!!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


