Free P4 pliers stiffness after moderate or heavy use
-
@tango44 said:
NO, let me clarify the situation.
The first P2 that I bought was sent back to Leatherman with the stucked pliers.
Leatherman sent me back a brand new P2 as a warranty replacement.
But the second I opened the package the pliers failed to me cutting a hanger.
I decide to keep it and I use the ball-peen hammer almost on a daily basis to free the pliers.
That's is why my P2 is that way.Thank you.
Thanks for clarifying.

But, still... LM telling you to hammer their tool to fix it?!?
And the first one had grease and a polishing stone when you bought it?
-
@tango44 said:
NO, let me clarify the situation.
The first P2 that I bought was sent back to Leatherman with the stucked pliers.
Leatherman sent me back a brand new P2 as a warranty replacement.
But the second I opened the package the pliers failed to me cutting a hanger.
I decide to keep it and I use the ball-peen hammer almost on a daily basis to free the pliers.
That's is why my P2 is that way.Thank you.
Thanks for the clarification, but still not ideal.
Even though I have my complains to P4, I am actually a big fan of the magnetic feature, it's handy and fun to use. But if LM strategy is to count on customers not keep on sending it back, and eventually learn to live with a stuck pliers or ball peen their own pliers...that is a bit much for a $140 tool.
-
@Aloha said:
Thanks the clarification. I hope LM was not in such a rush to get a new product to market that they fouled up. ** So now when I see the grey sheath I know the person has a tool with messed up plier**
Yeah shots fired
.:o
but
:DThanks for the clarification but still I would not be happy

-
So not giving up on my P2 (as a doorstop or shelf queen), I’m going to try my old method to work in the stiff pliers...rather than the ball peen or warranty route.
After a few minutes of open/closing ’exercise’, I could feel warmth on the pivot. A clear sign of friction binding.
A drop of light oil drew out a little grey filings. Enough to show there’s metal on metal wear taking place.
So I’ll soak the P2 in some detergent, dry it off and work the pivot dry to get maximum wear. Then oil to draw out the filings, and repeat.
May take a day or two, but will feed back my results.


-
I concure to what Max is telling, i tried before the hammering to open and close the pliers several minutes till it got warm. I used 2t engine oil to lubricate the bolt, some black ooze came one one side off, yet after several days i abandoned the procedure ( i got really tired).
I hope your approach Max, using it dry, will be more succesfull. -
...will load up some movies...

-
This guy from italy posted a video yesterday:
https://youtu.be/1yBwF6Io6KU -
This is ridiculous for a tool in that price range

And LM customer support telling customers to whack their tools is even more so

-
Thanks for the video link tango 44

-
I fixed this issue with some very thin polishing compound. Applied a bit to the pivot and opened and closed the pliers for quite a while. When they got to feeling nice and smooth again I flushed them very well with WD40.
-
Well...after 3 days of on-and-off ‘exercise’, including pressing some automotive abrasive into the pivot, I get beautiful free swinging pliers...until I squeeze them, and they bind up again.

There’s clearly an engineering geometry issue at play here. Not something I’m going to be able to fix, so it’s going back the shop. :-[
They can send it in for warranty. Hopefully I don’t get it back whacked, but I get one that works.
Have done a video here https://youtu.be/NFsneeJLltc showing that I need over 500g of pressure to close the pliers when they bind, and that after a wiggle, they are free again. Not acceptable Leatherman.


-
That smurfing sucks >:(
-
I’ll give mine a really hard squeeze tomorrow to see what happens. Maybe I didn’t fix it after all?
-
If I had to guess (and without taking an angle grinder to one, that's all I can do), I'd say it's due to the shave of the void that the plier rivet is formed into. Specifically, having too obtuse an angle at the bottom of the void.
Excuse the quality of the attached sketch, it was just freehand. Note on the top illustration, the void is a 90o countersink. This leaves a 45o angle on rivet and plier head from the plane on which the two halves of the plier head rub. Squeezing the pliers forces each half of the plier head in a shear action onto either side of the rivet, wedging the upper plier half between the lower plier half, and the 45o angle of the rivet head. At 45o or larger, the head shouldn't lock.
On the second illustration, a 120o or larger countersink, would leave a 30o included angle or less between mating plier faces and the rivet head. The smaller that angle, the more it will lock up like a Morse taper. Polishing it won't help either. It will just increase the amount of surface area in contact, and possibly make it worse - unless the vertical play is greater than the horizontal play.
This is all purely speculative, and one would hope that a 30+ year manufacturer of pliers wouldn't make such a fundamental error, that the numpty typing this, who's never made a pair of pliers in his life, can spot.

So, as I say, this is complete guesswork, and I might be barking up a lamppost, mistaking it for a tree. If however I am right, this needs a fundamental redesign. As for fixing pliers you already own, the only solution I can think of is to stretch/sprain the rivet pin, so those two faces are slightly too far apart to jam up in. However, this would also adversely affect wire cutting, particularly on fine stranded wire.

-
Note, a bent rivet pin could lead to the same issue, but without knowing which way it's bent, you wouldn't know where to whack it to improve matters.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
