Free P4 pliers stiffness after moderate or heavy use
-
...will load up some movies...

-
This guy from italy posted a video yesterday:
https://youtu.be/1yBwF6Io6KU -
This is ridiculous for a tool in that price range

And LM customer support telling customers to whack their tools is even more so

-
Thanks for the video link tango 44

-
I fixed this issue with some very thin polishing compound. Applied a bit to the pivot and opened and closed the pliers for quite a while. When they got to feeling nice and smooth again I flushed them very well with WD40.
-
Well...after 3 days of on-and-off ‘exercise’, including pressing some automotive abrasive into the pivot, I get beautiful free swinging pliers...until I squeeze them, and they bind up again.

There’s clearly an engineering geometry issue at play here. Not something I’m going to be able to fix, so it’s going back the shop. :-[
They can send it in for warranty. Hopefully I don’t get it back whacked, but I get one that works.
Have done a video here https://youtu.be/NFsneeJLltc showing that I need over 500g of pressure to close the pliers when they bind, and that after a wiggle, they are free again. Not acceptable Leatherman.


-
That smurfing sucks >:(
-
I’ll give mine a really hard squeeze tomorrow to see what happens. Maybe I didn’t fix it after all?
-
If I had to guess (and without taking an angle grinder to one, that's all I can do), I'd say it's due to the shave of the void that the plier rivet is formed into. Specifically, having too obtuse an angle at the bottom of the void.
Excuse the quality of the attached sketch, it was just freehand. Note on the top illustration, the void is a 90o countersink. This leaves a 45o angle on rivet and plier head from the plane on which the two halves of the plier head rub. Squeezing the pliers forces each half of the plier head in a shear action onto either side of the rivet, wedging the upper plier half between the lower plier half, and the 45o angle of the rivet head. At 45o or larger, the head shouldn't lock.
On the second illustration, a 120o or larger countersink, would leave a 30o included angle or less between mating plier faces and the rivet head. The smaller that angle, the more it will lock up like a Morse taper. Polishing it won't help either. It will just increase the amount of surface area in contact, and possibly make it worse - unless the vertical play is greater than the horizontal play.
This is all purely speculative, and one would hope that a 30+ year manufacturer of pliers wouldn't make such a fundamental error, that the numpty typing this, who's never made a pair of pliers in his life, can spot.

So, as I say, this is complete guesswork, and I might be barking up a lamppost, mistaking it for a tree. If however I am right, this needs a fundamental redesign. As for fixing pliers you already own, the only solution I can think of is to stretch/sprain the rivet pin, so those two faces are slightly too far apart to jam up in. However, this would also adversely affect wire cutting, particularly on fine stranded wire.

-
Note, a bent rivet pin could lead to the same issue, but without knowing which way it's bent, you wouldn't know where to whack it to improve matters.
-
I see you reasoning AL. It does appear the halves are getting pressed together, probably as a result of the countersink head exerting a force at an angle to the squeezing plane.
I do see this as an engineering flaw, as this cannot be considered QC oversight or random defect. It's baked into the design, as far too many are reporting the issue.
It means that I could never recommend the P2 or P4, unless Leatherman came out with a statement/recall addressing the issue.
Very sad, as even with all its problems (magnets, tool/blade deployment, handle hot spots, poor balance, clackety noise), it's grown on me. :D
-
If I was going to attempt to fix them, here's what I would try...
WARNING! THIS MAY DESTROY THE PLIERS!!!

... don't say you weren't warned!

Firstly, get the pliers the right way up. On one plier half, the rivet stays fixed to the head, and on the other half, the head pivots around the rivet. You want the fixed side down, and the moving side up. With the pliers open, support the uppermost half of the pliers only. Vice jaws might be the easiest way. If you wallop the rivet in this position, both the pivot and lower half of the jaws can move downwards. (see attached pic)
In order to direct the force accurately, I'd use two ball pein hammers. One would be placed ball down, directly in the centre of the rivet, with the hammer face pointing up. When you slap that face with the second hammer, the ball will force into the centre of the rivet, hopefully distorting it enough to create a little more play between the two mating plier faces.
BUT THESE ARE CAST PLIER HEADS, AND YOU MIGHT SNAP A JAW OFF! :ahhh
In effect, this is a reversal of the repair where you use a centre punch around the periphery of the rivet head, to reduce that working space in which the movable jaw turns. You want to try to create a little more space, so it doesn't jam up. Just like with the centre punch repair, you don't want to bray the life out of it and end up clamping the two halves solid, just bed it in gently, a little at a time, and check often.
**
IF YOU BUST THEM AND VOID THE WARRANTY, DON'T COME RUNNING TO ME!!!**Three warnings should be enough, I reckon :D Obviously, this all works on my assumption on what the underlying problem is, which may or may not be correct
The safest option (and recommended course of action) is of course to send the smurfing things back to the smurfing muppets that smurfed them up in the first place!!!
-
Beautiful and clear diagrams, Al.

If locking taper ever comes up in school I'll think of your diagram. :D -
As do I :D
Your theorie is sound Al
-
Had the same problem with the pliers seizing on my P2, but I also had the same problem with pliers seizing when pressure applied with my Rebar, Wave Gen 2, Wave plus, Charge Plus and Surge to name a few. Older Leatherman pliers ie- Fuse, OG Supertool, gen 1 Wave, etc don’t have that problem at all.
I managed to fix all my troublesome pliers, inc the Free P2 by clamping one side of the plier’s jaws in a vice(with pads) and using a hammer and large punch or flat drift to hit either side of the pivot on the inside of the unsupported plier. Also applying heat via a heat gun or gas to the pivot area prior to tapping the sides of the plier. Therefore freeing up the pliers. Each time checking the pliers along the way by squeezing the pliers to check for seizing, until it gets to a point where they don’t seize up anymore.
Also while heating the plier head I added a decent oil - I used wet finish line chain oil or Morgan blue race oil (medium thickness) and worked it into the pivot on both sides and into the plier from all sides, while hot and working the pliers up and down while one side clamped in the vice. Then wait for it to cool down, clean up then relive with a decent fine lube/oil.
Pain to do but they now run smooth with no play. -
I also removed the replaceable cutters so they didn’t interfere with each other when the pliers were closed more, otherwise you’ll damage the cutters/pliers when trying to tap apart/free up the pliers.

-
@AimlessWanderer said:
Polishing it won't help either.You might be on to something. I did what any sane tool enthusiast would do. I grabbed my morning coffee, my P2 and some thick steel wire and started cutting and bending. You are right, it's very tight once again.
This is disappointing, especially for a tool at this price point.
I bought this one right after they went on sale here. Do we know if this only happens to early production runs? Probably not if it really does turn out to be a design flaw.
-
Although me and Olives666 have offered two different methods of stretching the rivet slightly, I would still recommend returning the defective tools to Leatherman wherever practical to do so. If customers continue to accommodate their failings, Leatherman will be under little pressure to make the necessary changes to ensure this doesn't happen again. For the money their tools sell for, they should be right when they come out of the box, and nobody should have to bash anything with a hammer. The more tools that are returned to them, the higher the incentive for them to address the root causes, and stop sending out tools with these kind of issues.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login