Free P4 pliers stiffness after moderate or heavy use
-
@AimlessWanderer said:
Polishing it won't help either.You might be on to something. I did what any sane tool enthusiast would do. I grabbed my morning coffee, my P2 and some thick steel wire and started cutting and bending. You are right, it's very tight once again.
This is disappointing, especially for a tool at this price point.
I bought this one right after they went on sale here. Do we know if this only happens to early production runs? Probably not if it really does turn out to be a design flaw.
-
Although me and Olives666 have offered two different methods of stretching the rivet slightly, I would still recommend returning the defective tools to Leatherman wherever practical to do so. If customers continue to accommodate their failings, Leatherman will be under little pressure to make the necessary changes to ensure this doesn't happen again. For the money their tools sell for, they should be right when they come out of the box, and nobody should have to bash anything with a hammer. The more tools that are returned to them, the higher the incentive for them to address the root causes, and stop sending out tools with these kind of issues.
-
I agree, but with my first P2 they just canged for one in the same condition.
I have contacted Leatherman about the issue and they just answer: You are welcome to send to our warranty program and thats it.
Both of the tools that have the same problem where made in 06/19 I wonder if other people have newer tools with the same problem?
I don't think Leatherman is giving the attention or level of importance to this issue.
I hope they do it soon. -
@tango44 said:
I agree, but with my first P2 they just canged for one in the same condition.
<snip>
I don't think Leatherman is giving the attention or level of importance to this issue.That's why customers need to keep sending them back. Every time.
Leatherman clearly think these are acceptable. Customers clearly do not.
I personally agree with the customers. These are poorly designed/made.Leatherman need to be told that this level of quality is unacceptable, and the only way to do that, is keep sending back every single tool that is not up to the standard expected of a tool at that price. They'll get the message eventually. Social media users should spread the word too, including links back to this thread, so they have a couple of options to try, should they choose to attempt correction themselves (not all countries have the same level of warranty support).
-
This is very disappointing. LMs response is to send a new tool out under warranty :dunno:. They should also be paying for you to do that as well since its clearly a issue on their part.
What's so darn funny is how much they belittled the other offerings ( well that one tattooed guy did ) when announcing this stool ( no typo ).
When I see the grey sheath I'll know the pliers bind up, while my tool in the black sheath performs wonderfully. :facepalm:
-
He forgot that part, where the pliers become unusable after use...

Marketing BS, what do you expect? I don‘t believe any marketing videos I see from manufacturers. Of course they only show you the good stuff. Reviews should be done by independent parties. You just have to make sure they are really independent, and didn‘t „forget“ to mention that they got money for that review...
-
@Aloha said:
This is very disappointing. LMs response is to send a new tool out under warranty
. They should also be paying for you to do that as well since its clearly a issue on their part.What's so darn funny is how much they belittled the other offerings ( well that one tattooed guy did ) when announcing this stool ( no typo ).
When I see the grey sheath I'll know the pliers bind up, while my tool in the black sheath performs wonderfully.

That vid said he's the Product Manager. Does that mean he's the man responsible for these failures?
-
Hopefully his bonus evaporators as their profits are eaten by warranty claims. They can give him the job of responding to all the customer complaints.
And here are their official social media channels, if anyone has the inclination to use these platforms to start a discussion...
https://www.instagram.com/leathermantools/
https://m.facebook.com/Leatherman/
https://mobile.twitter.com/leatherman
https://m.youtube.com/user/LeathermanMedia -
Locking taper. Fascinating. I learn something new every day.
-
True locking tapers are typically a lot less than the 30o shown, but over the years I have found that stuff can have a nasty habit of jamming up when you don't want it to, at or around 30o. I've had it with cutting tools (taper drills and bore forming tools), taper gibs, self aligning bushings etc. A real pain in the well padded area!
If the void is drilled with an indexable insert U drill, there's a good chance that the face transition is less than 30o anyway. If they use an indexable insert stepped drill, which would be the most efficient way to drill out the castings, it's likely to have a TPMT insert for the counterbore, set around 15 to 18 degrees. That would fit these symptoms perfectly.
That's what happens when you gear your production facilities around production efficiency, rather than what the component actually needs. Seen it far too often.
-
@Max Stone said:
Well...after 3 days of on-and-off ‘exercise’, including pressing some automotive abrasive into the pivot, I get beautiful free swinging pliers...until I squeeze them, and they bind up again.
There’s clearly an engineering geometry issue at play here. Not something I’m going to be able to fix, so it’s going back the shop. :-[
They can send it in for warranty. Hopefully I don’t get it back whacked, but I get one that works.
Have done a video here https://youtu.be/NFsneeJLltc showing that I need over 500g of pressure to close the pliers when they bind, and that after a wiggle, they are free again. Not acceptable Leatherman.

No smurf, this sucks!
I had mine right in front me on the table, and just can't help but to give it a firm hand-shake squeeze, and guess what--I just joined the club and now it won't move freely. ::) Can't imagine what's gonna happen if I give it a real squeeze or need it to cut something.
I gave my old Charge the same squeeze, it binds a little bit but I guessed I have used it enough it frees right up after moving the handles couple of times.(or maybe the handle is heavier?)
Gave many times harder a squeeze to Victorinox Spirit and Swisstool, until the handles bow inward, no binding whatsoever.
I once said somewhere that this tool is not well thought thru, and only focusing on the aesthetic or appearance, I hate to be right on this. Even cheaper tools from 20+ years ago can do better.

-
@comis said:
No smurf, this sucks!I had mine right in front me on the table, and just can't help but to give it a firm hand-shake squeeze, and guess what--I just joined the club and now it won't move freely. ::) Can't imagine what's gonna happen if I give it a real squeeze or need it to cut something.
I gave my old Charge the same squeeze, it binds a little bit but I guessed I have used it enough it frees right up after moving the handles couple of times.(or maybe the handle is heavier?)
Gave many times harder a squeeze to Victorinox Spirit and Swisstool, until the handles bow inward, no binding whatsoever.
I once said somewhere that this tool is not well thought thru, and only focusing on the aesthetic or appearance, I hate to be right on this. Even cheaper tools from 20+ years ago can do better.

#PSTclub4Life
(Disclaimer: my only LM is a Kick.)
-
@AimlessWanderer said:
True locking tapers are typically a lot less than the 30o shown, but over the years I have found that stuff can have a nasty habit of jamming up when you don't want it to, at or around 30o. I've had it with cutting tools (taper drills and bore forming tools), taper gibs, self aligning bushings etc. A real pain in the well padded area!If the void is drilled with an indexable insert U drill, there's a good chance that the face transition is less than 30o anyway. If they use an indexable insert stepped drill, which would be the most efficient way to drill out the castings, it's likely to have a TPMT insert for the counterbore, set around 15 to 18 degrees. That would fit these symptoms perfectly.
That's what happens when you gear your production facilities around production efficiency, rather than what the component actually needs. Seen it far too often.
I think every knife/tool maker may eventually come to that point when you get large enough, just a matter of choice between greed vs customer satisfaction.
-
So I returned my P2 to the retail store today as a warranty claim. The Leatherman distributor will collect it next week from the store to action.
Out of interest, I asked the salesman if we could test the P2 and P4 they had in their display cabinet.
Guest what...after a squeeze they both locked up nice a tight. The salesman’s eyes went large and he said he’d show the distributor when he came in.
Seems the problem is not so isolated... ???
-
This is disgraceful, Leatherman should be ashamed that they let these tools out to the public. Someone must have known about this problem

-
My P2 is on it’s way back to the importer. I’ve asked for a Wave as a replacement but they told me that’s not possible. I guess the replacement P2 will be sold unused, I’m done with this.
Makes you wonder, I have an old PST that I’ve used fairly hard for three decades and it still functions fine. Newer isn’t always better.
-
I'm not sure what to think
. If as it seems LM is content to lean on their warranty then this is really unfortunate. Makes you wonder how many have to come back for them to fix problem and not lean on warranty
. -
A fair amount of users will never crank down on them so hard that they’ll bind the pliers, so the number of returns could be limited. Either way, it’s disappointing.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
