The Victorinox Waiter Appreciation Society
-
Front view

Sent from my Nokia 1 using Tapatalk
-
Open view.

Sent from my Nokia 1 using Tapatalk
-
Side view showing the thickness. The oak started at 4mm thick. Now a little less from the sanding, but does create a bit more bulk to the Waiter!

Sent from my Nokia 1 using Tapatalk
-
-
Looks great GreyLife![emoji106]
Sent from my iPhone using Tapatalk
-
Thank you [emoji106]
Sent from my Nokia 1 using Tapatalk
-
@GreyLife said:
Side view showing the thickness. The oak started at 4mm thick. Now a little less from the sanding, but does create a bit more bulk to the Waiter!
Sent from my Nokia 1 using Tapatalk
Very nice GL
I have been thinking of doing a similar mod to my other sak. Do you mind briefly sharing how you did it? Did you use any power tools or just sand paper? Thanks. -
Thanks, no power tools were used! It was mainly done using tools from SwissChamp and Leatherman. The fine finishing was all sandpaper, finishing with 1000 grit paper and teak oil. The grooves for the tools were done with the file/saw from SwissChamp, and for fine finish wrapped sandpaper around the file. To get the initial positions of the rivets, I gently squeezed the SAK and wood in a soft jaw vice and then used the chisel tool from SwissChamp to 'drill' the holes until the wood lay flat against the side of the SAK. Finally I used superglue to hold the scales on. Hope this helps!
Sent from my Nokia 1 using Tapatalk
-
That's an awesome mod Greylife!
-
@GreyLife said:
Thanks, no power tools were used! It was mainly done using tools from SwissChamp and Leatherman. The fine finishing was all sandpaper, finishing with 1000 grit paper and teak oil. The grooves for the tools were done with the file/saw from SwissChamp, and for fine finish wrapped sandpaper around the file. To get the initial positions of the rivets, I gently squeezed the SAK and wood in a soft jaw vice and then used the chisel tool from SwissChamp to 'drill' the holes until the wood lay flat against the side of the SAK. Finally I used superglue to hold the scales on. Hope this helps!Sent from my Nokia 1 using Tapatalk
Thank you GL. This is very helpful. I will get to work soon !
-
...got a Wenger Entree' version. Has no split ring, checked our Wiki but...didn't see anything by phone...just wondering...

-
@roamingcat said:
Picture?...you'll have to settle for the Sak Wiki above. I'm pic challenged right now...
-
Not sure if it's still the case, but was the Waiter not the tool with the best Function/Layer ratio?
I remember having one, unfortunately it saw very little use before someone decided they needed it more than I did :'(
-
@TonySal said:
...got a Wenger Entree' version. Has no split ring, checked our Wiki but...didn't see anything by phone...just wondering...
It is a Victorinox Waiter that I have....if you look at my previous post you will see it was a nylon economy scaled Waiter....and there is a split ring too! On the front side of the main blade are the words "VICTORINOX SWITZERLAND STAINLESS ROSTFREI" on the reverse is "OFFICIER SUISSE" along with the small cross and crossbow.

Sent from my Nokia 1 using Tapatalk
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
