Tiny tiny screwdriver with 4 heads - anyone?
-
-
So, first physical versions in hardened stainless steel. The one on the bottom is the cross driver - it actually works better than I thought on surface screws. The risk of getting cut on the flat drivers seems less than I imagined. Or I might just haven been lucky.

In the lower middle is the new keychain version. A fair bit bigger than the cross driver but still quite small.
The drivers have longer reach than typical screwdriver bits, and the body itself about the same size as a bit holder. Each driver opens up and locks along the centerline of the tool body. For more torque the drivers on the opposite side can be folded out to the side and used for leverage. Nice rounded corners and quite pocket and keychain friendly.
For keychain use the concept is a little harness that is permanently connected to the keychain, and from which the tool itself can easily be disconnected from. So one doesn't have to mess around with an entire keychain when one wants use it.
(It still needs to get the rivets on. I'm on the fence about polishing it? The locks are clunky without polished surfaces, but then again the slightly rough surface is actually nice to grip.)
It's been a fun one at least.



-
They have turned out really well Vidar

Itβs still difficult to grasp just how small these are. I know you have them shown next to SAKs and other tools, but maybe a comparison to a matchbox will also help. These tools are really tiny!
My preference is the folding tool.

-
-
@Max Stone said:
They have turned out really well Vidar
Itβs still difficult to grasp just how small these are. I know you have them shown next to SAKs and other tools, but maybe a comparison to a matchbox will also help. These tools are really tiny!
My preference is the folding tool.

Thank you!
I think they would look better polished, but the grip would be worse off. Maybe some middle ground. Either way, these are just for proof of concept and adjusting tolerances so not sure how much I'll put into looks at this point.I thought about matchboxes, but my matchboxes around here were different sizes.
So I figured not a good reference? Either way the folding one is 35 mm long, while the cross one is 19mm. Next time I'll put them next to a ruler.. 
-
@Don Pablo said:
Both of them are sweet.
I think I prefer the cross driver over the folding one because of budget concerns. :ahhh
But I can see the usefulness of the folding one.They are both silly expensive for what they are!
:ahhh Then again functionality is far from everything.The folding one is clearly the winner for usefulness. The drivers having reach, torque and being at the centerline do make a difference.
-
And maybe one can open the opposite driver to 90 degrees for extra torque?
-
@Mechanickal said:
And maybe one can open the opposite driver to 90 degrees for extra torque?Yes, that is part of the concept.
I put in some temporary rivets to check how it works and the opening closing mechanisms are fine. Yay!

Here are some more picture with more scale items, a picture with the tiny flat driver active, and one showing the reach.



-
That's eenyweeny

-
-
Eenyweeny problems

-
-
-
-
Thanks!
It is actually kind of cute. Then again I think the same about my excavator so I might be damaged goods.
The mechanisms to keep the drivers folded in when not in use works, and the locks work too. The springs I got for the locks are on the weak side though. I need to get or make some stronger ones for a proper snappy feel.
In the meantime I'll give it some pocket time, and maybe do the keychain harness for it.
-
-
@gregozedobe said:
Just a suggestion: make the centre hole a 1/4" hex so it could be used as a bit driver as well (might as well add more functionality)Thank exactly what I was itching to write [emoji23][emoji1319]
-
@alexanderre said:
Thank exactly what I was itching to write [emoji23][emoji1319]It is still way too small for that.
With a hole for a 1/4" hex in the middle there would be next to no middle left.In general my design thinking is that if some feature is added it has to work properly. There are too many tools around aiming to do all kinds of stuff and ending up doing very few properly. I'd rather focus on fewer features but have them working well. I do get that for many multitools have a long list of "functions" is a major selling point, but I'd like to focus on actual use and the end user.
Adding features usually add costs as well so that has to be justified too. (This one in particular though is more of a fun project so I've already utterly disregarded all cost considerations and design for assembly practices ::) I even considered making the main body of the larger one in titanium :D).
-
-
@Vidar said:
Thank you!
I think they would look better polished, but the grip would be worse off. Maybe some middle ground. Either way, these are just for proof of concept and adjusting tolerances so not sure how much I'll put into looks at this point.I thought about matchboxes, but my matchboxes around here were different sizes.
So I figured not a good reference? Either way the folding one is 35 mm long, while the cross one is 19mm. Next time I'll put them next to a ruler.. 
Like the folding one. I'd go for the rough / stonewashed look. It's perfect to be carried in a keychain. Being polished, it would get scratched in no time and end up looking bad.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better π
Register Login