Tiny tiny screwdriver with 4 heads - anyone?
-
@Max Stone said:
They have turned out really well Vidar
Itβs still difficult to grasp just how small these are. I know you have them shown next to SAKs and other tools, but maybe a comparison to a matchbox will also help. These tools are really tiny!
My preference is the folding tool.

Thank you!
I think they would look better polished, but the grip would be worse off. Maybe some middle ground. Either way, these are just for proof of concept and adjusting tolerances so not sure how much I'll put into looks at this point.I thought about matchboxes, but my matchboxes around here were different sizes.
So I figured not a good reference? Either way the folding one is 35 mm long, while the cross one is 19mm. Next time I'll put them next to a ruler.. 
-
@Don Pablo said:
Both of them are sweet.
I think I prefer the cross driver over the folding one because of budget concerns. :ahhh
But I can see the usefulness of the folding one.They are both silly expensive for what they are!
:ahhh Then again functionality is far from everything.The folding one is clearly the winner for usefulness. The drivers having reach, torque and being at the centerline do make a difference.
-
And maybe one can open the opposite driver to 90 degrees for extra torque?
-
@Mechanickal said:
And maybe one can open the opposite driver to 90 degrees for extra torque?Yes, that is part of the concept.
I put in some temporary rivets to check how it works and the opening closing mechanisms are fine. Yay!

Here are some more picture with more scale items, a picture with the tiny flat driver active, and one showing the reach.



-
That's eenyweeny

-
-
Eenyweeny problems

-
-
-
-
Thanks!
It is actually kind of cute. Then again I think the same about my excavator so I might be damaged goods.
The mechanisms to keep the drivers folded in when not in use works, and the locks work too. The springs I got for the locks are on the weak side though. I need to get or make some stronger ones for a proper snappy feel.
In the meantime I'll give it some pocket time, and maybe do the keychain harness for it.
-
-
@gregozedobe said:
Just a suggestion: make the centre hole a 1/4" hex so it could be used as a bit driver as well (might as well add more functionality)Thank exactly what I was itching to write [emoji23][emoji1319]
-
@alexanderre said:
Thank exactly what I was itching to write [emoji23][emoji1319]It is still way too small for that.
With a hole for a 1/4" hex in the middle there would be next to no middle left.In general my design thinking is that if some feature is added it has to work properly. There are too many tools around aiming to do all kinds of stuff and ending up doing very few properly. I'd rather focus on fewer features but have them working well. I do get that for many multitools have a long list of "functions" is a major selling point, but I'd like to focus on actual use and the end user.
Adding features usually add costs as well so that has to be justified too. (This one in particular though is more of a fun project so I've already utterly disregarded all cost considerations and design for assembly practices ::) I even considered making the main body of the larger one in titanium :D).
-
-
@Vidar said:
Thank you!
I think they would look better polished, but the grip would be worse off. Maybe some middle ground. Either way, these are just for proof of concept and adjusting tolerances so not sure how much I'll put into looks at this point.I thought about matchboxes, but my matchboxes around here were different sizes.
So I figured not a good reference? Either way the folding one is 35 mm long, while the cross one is 19mm. Next time I'll put them next to a ruler.. 
Like the folding one. I'd go for the rough / stonewashed look. It's perfect to be carried in a keychain. Being polished, it would get scratched in no time and end up looking bad.

-
@pfrsantos said:
Like the folding one. I'd go for the rough / stonewashed look. It's perfect to be carried in a keychain. Being polished, it would get scratched in no time and end up looking bad.

I have to admit the current look, being fairly close to stonewashed, is growing on me. I've been carrying it in pockets for a while now, but it really needs a keychain just to keep track of it. I'm thinking of maybe doing the keychain connector to match the pins. Maybe some bronze. Or alternatively a stainless steel similar to the main color.
It might do fine polished as well as it hardened steel throughout. Softer things like keys, coin and such should not be a problem with regards to skratching. That said the hardness of this one is softer than it ought to be for a long life of screwdriving, so that needs improving if I'm ever to make more of these.
Functionality is actually good. It works pretty much as a stubby screw driver, so it is easy to keep pressure down while turning. I got lucky there!

-
That folding one is really neat!

-
@Vidar said:
They are both silly expensive for what they are!
:ahhh Then again functionality is far from everything.The folding one is clearly the winner for usefulness. The drivers having reach, torque and being at the centerline do make a difference.
You called? I want one of those folding drivers

That concept I like a lot. Just for comparison, maybe have a look at Big Idea Design prices... expensive is the right price for EDC gear

-
I do think if it can come down to their price levels it would be marketable. Still some way to go to get there. There was just no concern about costs when I made this. Just getting the springs for the locking mechanisms in place is quite the trick.
To some extent this one is to me as I suspect avant garde is for fashion designers - made more for the process itself and where it can lead to later rather than a marketable end product. I picked up quite a few tricks with the locks and springs making this one, and I can certainly see those be used elsewhere too later.
I could have this factory made within a few weeks, but the costs as of now just doesn't make sense. The costs are coming down though. We'll see where it goes eventually, but hopefully I have the more serious EDC designs ready well before then.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better π
Register Login