Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Easy Swiss Champ blade swap

Scheduled Pinned Locked Moved The Mod Squad
20 Posts 1 Posters 1.2k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Easy Swiss Champ blade swap
Easy Swiss Champ blade swap
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Max Stone Offline
    Max Stone
    Posts: 5,982
    Max Stone Offline
    Max Stone
    wrote on last edited by
    #4 Quote Reply

      The new blade fitted in easily. Needed a little pressure to center over the top of the exposed pin. I put some tape on the blade for some protection.

      Now ready to drive through the new pin. Don’t forget to slide on the collar, as once you’ve driven the new pin down, that’s it’s final position.

      Here you can see progress at the halfway point, new pin at the top, old coming out the bottom. I tap through with the SAK on the vice with the jaws slightly open. When the original pin drops out, keep it for a future build, but you’ll need to reuse the collar. Finish tapping the new pin all the way down.

      7B07444F-FFEB-48EA-BB52-41A3287063FC.jpeg

      D98A3E86-7732-4D06-83C7-3294D0A08720.jpeg

      D3482283-B05B-46EC-8843-53DE57490C4F.jpeg

      B60C3E03-CC3B-4B25-BCF9-AFEC5E62B794.jpeg

      1 Reply Last reply
      • Max Stone Offline
        Max Stone
        Posts: 5,982
        Max Stone Offline
        Max Stone
        wrote on last edited by
        #5 Quote Reply

          Here’s the old pin and the new pin in place, ready for trimming. This is a good time to test the new blade and maybe have a cup of tea.

          To peen closed, I cut off just less than the thickness of the collar. I use a diamond cut-off disk on my Dremel to cut and grind a nice flat end on the pin.

          3215C600-6E81-4886-BE50-71AFDD490096.jpeg

          8FAD4F25-BEDD-4F7B-A101-45641B5813FB.jpeg

          C0E39FDB-371C-42CE-81E6-C090AFBBF740.jpeg

          38CAD2F6-8610-42B4-8D47-15423E423F0B.jpeg

          1 Reply Last reply
          • Max Stone Offline
            Max Stone
            Posts: 5,982
            Max Stone Offline
            Max Stone
            wrote on last edited by
            #6 Quote Reply

              After cutting, I polish the end which also takes off the sharp edge.

              I then put the collar back over the pin and use the anvil end of my vice to peen the pin into a rivet head shape. It’s important to peen enough to get a proper seat inside the collar, but also to close the layers tightly enough to not have wobble on the tools. To check, it helps to turn the SAK over and tap the opposite end of the pin when on the vice with the jaws open. Then turn back and continue to peen the top rivet on the anvil. It’s possible to have the fit too tight, and then the tools bind and won’t snap. But it’s generally a case of too much tool wiggle. So take time to check the peening is the correct tightness by testing the tools for wiggle.

              D8339E3C-5046-47E1-8C20-2BD734062347.jpeg

              280CAF5E-AB0B-4AF2-9821-119BD1AD2BD8.jpeg

              836F9E0D-87FB-4188-9FAC-341BF327CBD9.jpeg

              D52F48E0-DC03-4196-A97F-8D9A4E86708D.jpeg

              1 Reply Last reply
              • Max Stone Offline
                Max Stone
                Posts: 5,982
                Max Stone Offline
                Max Stone
                wrote on last edited by
                #7 Quote Reply

                  I polished up the rivet when done, and then gave the SAK a good wash, opening and closing all the tools to get it clean.

                  After a good rinse and dry, I snapped the scales back on. Oiled and all done!

                  9E75B200-B255-4935-9DE1-1E5CE526D038.jpeg

                  4CE147BD-47F9-4230-9827-6F2D29221B6D.jpeg

                  0AEC7A2F-E2F1-408B-A03B-7DA2F1535C0E.jpeg

                  EE78F1B3-5848-45AC-9764-C55129DBF5E3.jpeg

                  1 Reply Last reply
                  • magentus Offline
                    magentus
                    Admin Team
                    Posts: 21,659
                    magentus Offline
                    magentus
                    Admin Team
                    wrote on last edited by
                    #8 Quote Reply

                      Beautifully done 'how to' there Max :cheers:
                      Lovely pics.

                      1 Reply Last reply
                      • Max Stone Offline
                        Max Stone
                        Posts: 5,982
                        Max Stone Offline
                        Max Stone
                        wrote on last edited by
                        #9 Quote Reply

                          Thanks magentus :hatsoff:

                          1 Reply Last reply
                          • PitCarver Offline
                            PitCarver
                            Posts: 3,025
                            PitCarver Offline
                            PitCarver
                            wrote on last edited by
                            #10 Quote Reply

                              Awesome job, Max.
                              Very good job.
                              I picked up a handyman special of 58mm's, that included a MiniChamp and 2 additional classics. Looked like someone had taken a grinder to the scissors and main blade on the MiniChamp, so I did basically the same as you.
                              Salvaged the scissors from 1 classic and the blade from the other. Drove the old pin out with the new, replacing the tools as I went along.
                              Funny, how every source said that I had to totally disassemble the knife in order to replace the tools...
                              This was my first, and only, so far, attempt at repair of a Victorinox.

                              I was pleased with the outcome.

                              1 Reply Last reply
                              • McStitchy Offline
                                McStitchy
                                Global Moderators
                                Posts: 19,785
                                McStitchy Offline
                                McStitchy
                                Global Moderators
                                wrote on last edited by
                                #11 Quote Reply

                                  Great job Max... well done :tu:
                                  I didn't try the push-through method yet.
                                  Will keep it in mind for sure after seeing this :D

                                  1 Reply Last reply
                                  • Max Stone Offline
                                    Max Stone
                                    Posts: 5,982
                                    Max Stone Offline
                                    Max Stone
                                    wrote on last edited by
                                    #12 Quote Reply

                                      Thanks PitCarverb and Matt. :hatsoff:

                                      If you measure the pin lengths it should be possible to replace any tool down the stack. I used the same method last year to replace the CS of a Ranger with a Phillips to make a Master Craftsman. So this is a viable method for both the center and outer pivots. :salute:

                                      1 Reply Last reply
                                      • NetsNJ Offline
                                        NetsNJ
                                        Posts: 676
                                        NetsNJ Offline
                                        NetsNJ
                                        wrote on last edited by
                                        #13 Quote Reply

                                          Amazingly instructional.

                                          1 Reply Last reply
                                          • Max Stone Offline
                                            Max Stone
                                            Posts: 5,982
                                            Max Stone Offline
                                            Max Stone
                                            wrote on last edited by
                                            #14 Quote Reply

                                              Thanks NetsNJ :hatsoff:

                                              1 Reply Last reply
                                              • SirVicaLot Offline
                                                SirVicaLot
                                                Posts: 5,979
                                                SirVicaLot Offline
                                                SirVicaLot
                                                wrote on last edited by
                                                #15 Quote Reply

                                                  Great work, Max! Great write-up as well! :like:

                                                  1 Reply Last reply
                                                  • Myron Offline
                                                    Myron
                                                    Posts: 2,432
                                                    Myron Offline
                                                    Myron
                                                    wrote on last edited by
                                                    #16 Quote Reply

                                                      Another awesome how-to! Thanks for taking the time to post this, Max. I really enjoyed reading it.

                                                      Myron

                                                      1 Reply Last reply
                                                      • Max Stone Offline
                                                        Max Stone
                                                        Posts: 5,982
                                                        Max Stone Offline
                                                        Max Stone
                                                        wrote on last edited by
                                                        #17 Quote Reply

                                                          Thanks Sir Vic, Myron. :hatsoff:

                                                          1 Reply Last reply
                                                          • Wspeed Offline
                                                            Wspeed
                                                            Posts: 76,225
                                                            Wspeed Offline
                                                            Wspeed
                                                            wrote on last edited by
                                                            #18 Quote Reply

                                                              Excellent work Max and great write up and pics :like: :tu:

                                                              1 Reply Last reply
                                                              • Max Stone Offline
                                                                Max Stone
                                                                Posts: 5,982
                                                                Max Stone Offline
                                                                Max Stone
                                                                wrote on last edited by
                                                                #19 Quote Reply

                                                                  Thank you Wim. :cheers:

                                                                  1 Reply Last reply

                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                  With your input, this post could be even better 💗

                                                                  Register Login

                                                                  1. Home
                                                                  2. Tool Talk
                                                                  3. The Mod Squad
                                                                  4. Easy Swiss Champ blade swap
                                                                  Reply
                                                                  • Reply as topic
                                                                  Log in to reply
                                                                  COMMUNITY LINKS
                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                  Operational Funds

                                                                  Help us keep the Unworkable working!

                                                                  Make A Donation
                                                                  November Goal: $300.00
                                                                  Due Date: Nov 30
                                                                  Total Receipts: $0.00
                                                                  Below Goal: $300.00
                                                                  0% funded
                                                                  • Login

                                                                  • Don't have an account? Register

                                                                  • Login or register to search.
                                                                  • First post
                                                                    Last post
                                                                  0