I made a thing...
-
Reposting photos (thanks Photobucket):




-
The Mk.I was constructed and left behind at someone else's property. More recently I set about making a portable version.
I know some people call this sort of thing a Sawbuck; to me that doesn't make sense as to buck something with a chainsaw is to saw it. So that's like calling it a Sawsaw.
It's a 'horse' for sawing or bucking so I say it's a Sawhorse or a Buckhorse. I'll go with the latter to differentiate it from a normal sawhorse.So I started building my Buckhorse Mk.II like those you often see except I wanted more supports (to stop the logs dropping when cut) but didn't need any more legs. It wasn't turning out very well...

So I had a rethink and made this out of old pallet wood:


It folds up for storage but because of where the cross members are joined to the legs it has to fold the 'wrong' way.
The slots are at 300mm centres and the supports between them stop logs from dropping too much when bucked.
The legs are secured at a 60° angle by a rope with a double overhand stopper knot that slides into a slot. -
Nice jig!

Looks so useful. Any problems with the logs moving as you cut? -
Big ones no, small diameter ones yes. The smaller ones also sit too low in relation to the cutting slots.
The legs get in the way of the saw body although not so much since I trimmed them back.I have ideas for a Mk.III to overcome all these issues but it needs more thought...
-
Nice one!
As the old saw horse totally mysteriously ( ::) ) ended up broken and kind of flat last year I might copy that setup if you don't mind?

-
Go for it.
If I didn't want it copied then putting it on the interweb wouldn't have been a good idea.
Or you could wait for Mk.III, which may or may not happen...Feel free to ask any questions.
Spoiler:
The notches in the legs are unnecessary. They were to help lock them at 60° with the previous configuration and I reused the timber. Another way would have been to bevel one edge of the cross members. -
Nice work, Synco

I'd leave it exactly as it is, and make a couple of slipper blocks which hook over a rail (front rail if using a chainsaw, or a manual saw which push cuts, or back rail if it's a pull saw). This will lift the workpiece up and against whichever rail is taking the load. Leave them both at the ends for long branches, or bring them either side of the centre slot for short pieces.

-
Good idea.

Another thought I had was to have some way of holding the thin pieces at one end and cantilevering it like some of those other products mentioned earlier. There could be two supports, each with a V cut to stop the log moving sideways. The outermost one is under the log and the innermost one is above it. Or that could be a completely separate apparatus.
-
The good thing with the slipper blocks, is that they are movable, and that they maintain the same working height with the saw. Also good for chocking a wonky branch (one on front rail, one on the back).
-
@Syncop8r said:
Big ones no, small diameter ones yes. The smaller ones also sit too low in relation to the cutting slots.
The legs get in the way of the saw body although not so much since I trimmed them back.I have ideas for a Mk.III to overcome all these issues but it needs more thought...
I have a home made sawhorse that I use some thick shock cord and a yachting cleat to hold the log down while I'm sawing (run the shock cord under then around the log and under again to the cleat for better grip on the log).
This works OK, but I prefer my Blokka cantilever saw horse as it is quicker to use.
Sorry, I can't find any current links for it, they stopped making them years ago, but the operating principle is the same as the "Saw Jaw":
https://arbtalk.co.uk/forums/topic/44577-sawhorses-some-new-improvements/?tab=comments#comment-698040
http://www.bsbgardenmachinery.com/chainsaws---log-splitters.html (scroll down to the video) -
I present to you..... the Buckhorse Mk.III!

A friend suggested I forget trying to make the crossed-over legs hold the log and instead make something that holds the log, then make the legs fold from that. So I took inspiration from my folding sawhorse design: /post/1730251
This took a bit of thinking and was harder to construct but it in a way it's simpler, it looks cleaner and works much better. There are no big pieces sticking up to get in the way of the chainsaw and the logs/branches are well supported.

It is made mostly from old pallets. A square rail at 45° creates a V shape for blocks to sit on with 50mm gaps between them (for the saw to pass through) every 300mm. The blocks (and the legs on one side) are fixed to the rail with long galvanised screws with hex heads. I used the same type of hinges as in the sawhorse except bigger and with a longer pin which means they are much sturdier. Each leg is 20° from vertical so there wasn't much room to get some of the screws in.

I was going to use rope or a chain to stop the legs from spreading but it isn't necessary. This thing ain't moving.
When you pick it up the legs naturally fold for easy storage.

-
The improvements continue ....

-
Note to self: Never lend anything to anyone. ::)


-
@gregozedobe said:
Are you only just learning that lesson ? I found that out decades ago, and it has saved me from a lot of annoyance ever since
Well I did learn that lesson, but I like to help people and I'm optimistic that others are as skilled or careful as me.
I know, silly me.
-
@Syncop8r said:
Well I did learn that lesson, but I like to help people and I'm optimistic that others are as skilled or careful as me.
I know, silly me.
When the urge to help overcomes me I just do whatever it is that needs to be done, that way I know my tools are (relatively) safe.
One exception is changing a flat tyre. I will loosen the tight wheel nuts for them, and explain in detail how to do it (and provide muscle for the actual wheel removal & replacement if really necessary), but if the driver doesn't want to make any effort whatsoever then I am willing to leave them to whatever plan they had to fix their problem. Of course if they are truly physically unable I will help them out as much as needed.
It may sound harsh, but the situation is literally is not MY problem, and if you want to wait around for however many hours it will take for the people who you have paid to do this work (eg roadside assistance), then I am perfectly willing and able to follow your plan to the letter.
-
If I change a tyre for someone I try to teach them how to do it as well.
Once I had a flat tyre and friends on board helped. A few days or perhaps a week or so later (before I fixed the tyre and swapped it back in) I heard a noise coming from one of the wheels. The nuts were on backwards and had worked their way loose so that the wheel was starting to wobble. ::)
-
@Syncop8r said:
If I change a tyre for someone I try to teach them how to do it as well.Once I had a flat tyre and friends on board helped. A few days or perhaps a week or so later (before I fixed the tyre and swapped it back in) I heard a noise coming from one of the wheels. The nuts were on backwards and had worked their way loose so that the wheel was starting to wobble. ::)
Obviously whoever taught your friends how to change a wheel didn't do a very good job. :(
I'm sure when you are teaching someone then putting the nuts on the right way round is part of the learning process. If I am able to I usually try to explain why something needs to be done a particular way, in the hope they might remember it better when the time comes that they have to do it by themselves (without tuition).
-
@gregozedobe said:
When the urge to help overcomes me I just do whatever it is that needs to be done, that way I know my tools are (relatively) safe.One exception is changing a flat tyre. I will loosen the tight wheel nuts for them, and explain in detail how to do it (and provide muscle for the actual wheel removal & replacement if really necessary), but if the driver doesn't want to make any effort whatsoever then I am willing to leave them to whatever plan they had to fix their problem. Of course if they are truly physically unable I will help them out as much as needed.
It may sound harsh, but the situation is literally is not MY problem, and if you want to wait around for however many hours it will take for the people who you have paid to do this work (eg roadside assistance), then I am perfectly willing and able to follow your plan to the letter.

That's the only way they'll learn. Well, if they even get to learn. It's amazing how some people can forget how to do incredibly easy tasks when they only need to do it once or twice a year...

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
