ZapWizard's Leatherman Free P4 Mods
-
Here is the P2 stackup. Everything has been verified using calipers:
The P2 doesn't have any washers between the thin implements. It only has thicker washers on each end of the stack to account for the recesses in each scale.Amazing, thanks!
So looking at the layout, if it doesn't have washers to take out giving the extra 0.01 of room needed when i remove the file, is there a way to fit the T-shank? Or is there enough wiggle room in the design that 0.01 difference is negligible, and won't really change anything
This is all working on the assumption that my memory is correct and it's 0.18, that could well be a measurement from a previous iteration!
Thankyou again, and thanks to everyone for all the warm welcome messages!
-

Ya 0.01 isn't enough to worry about. If you find is loose, then you may need a very thin washer. (McMaster should have either a thin washer or precision shim that fits the bill.
If your replacing the scissors, then you remove the can opener or other thin implement.If you want to replace the knife instead, you simply swap all the thin tools to the same side as the t-shank holder, and the philips/flathead (or bit adapter) to the side with the scissors.
-
Mr. ZapWizard, I ordered the T-Shank holder the other day. I do have a question. I also ordered the screws you listed from McMaster-Carr. How far do they stick up from the handle, compared to your thumb stud. I'm currently using a sheath from RAE Gear. It has a lip that my thumb studs fit under, I'm just wondering if I'm going to have an issue with the screws in the T-Shank holder. I did see that McMaster-Carr has lower profile screws. Just trying to decide if I should order those. I've included a picture of how the thumb studs fit in the sheath.

-
The T-shank holder sits up as high as my thumb tabs do, the screws are about the same height (0.2mm shorter). You can always file/grind the surface down flatter.
-
@ZapWizard said:
The T-shank holder sits up as high as my thumb tabs do, the screws are about the same height (0.2mm shorter). You can always file/grind the surface down flatter.Thanks for the info!
-
I got my T-Shank holder today and installed. Very nice. I shortened my file and will do the saw tomorrow. It also fits in my RAE Gear sheathe just fine!
Thanks for all the effort you put into making my P4 a mini Surge! -
:ahhh
Too many cool mods!!!
Awesome work ! -
My P4 with some of the mods I've done..... Besides the ZapWizars's great products, I also sharpened the awl to make it proper one.

-
Great work on your mod, Slygrin


-
Installed the t-shank holder, see post above. I have a Surge, so I bought a new file and saw blades from Leatherman to use with the P4. I shortened the file and it will be the blade I use the most. I started looking at the saw blade and I can't make up my mind if I should shorten it or not. If I shorten it, it will not matter which one I have in the tool. If i leave the saw at the original length, it will have the advantage of having more cutting length, but I will not be able to close it. I would have to put the file back in to close it. Oh, the dilemma.... So, what would you do? Don't mind the cat hair in the picture....

-
I would leave the saw as long as possible if it were me
How much are we talking about shortening it BTW
The file would still be just as functional if it were a bit shorter but a saw on a MT is already a bit short so making it even shorter is never good :ahhh I think the OHT has a saw that is too short, it is functional but just barely :D -
I've decide to leave the saw blade alone. Another bonus is I can use the same blade with my Surge and only carry one. One thing I would recommend with the bit holder and t-shank holder. Sand and smooth out the back end of the bit. When deploying, I notice a little roughness. I don't find it a big enough issue to take it apart to fix, but I'll do it the next time I take it apart.
-
The T-Shank holder is done!
The produce page is live (store link in my signature)Coming up: A collaboration with fellow Multitool.org member Metropolicity
I shared my Leatherman FREE CAD T-Shank CAD data with him in exchange for his CAD file for his Leatherman Charge Scalpel holder
So now I can get cracking on a making one for the FREE series.Wow.

-
, part 2 :D
-
Small Free P4 based tool kit using some of ZapWizard's mods and accessories. The kit brings the versatility of some older Leatherman offerings to the Free series, and there is space for one or two Victorinox additions ;)


-
Amazing tool kit.
FYI, I am thinking about making a tweezer holder that replaces the pliers side spacer near the scissors. (Nylon piece with a small cutout really).
-
That all looks great, DT :o 8) Great pics and bit of kit

-
Thanks guys :D
Good news on the tweezers holder Zap, looking forward to that
I discovered I need to make a small notch in the file to allow the plier head tooth to engage the handle
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

