ZapWizard's Leatherman Free P4 Mods
-



How is this for one day of design.
I kept most of Metropolicity's profile for the actual blade grip, and then built around it.
It has a built-in thumb-tab, and because the blade is on the inside, it should help keep you thumb away from the blade while deploying.That said, I am going to only recommend either the 60A blade from Havalon, or the Wiebe Blades be used. This is because these are the only blades long enough to ensure the blade stays docked when using the pliers.
I will offer it in a mirrored version for replacing the serrated blade instead of the main blade.For now, I will sit on the design until my handles arrive.
-
@Dutch_Tooler said:
Small Free P4 based tool kit using some of ZapWizard's mods and accessories. The kit brings the versatility of some older Leatherman offerings to the Free series, and there is space for one or two Victorinox additions ;)
DT & ZapWizard -
Coming soon...
The Leatherman FREE P4, Klingon Edition
-

Hmm... the mirrored holder that goes where the serrated blade usually sits might be something to consider

-
@ZapWizard said:
Coming soon...
The Leatherman FREE P4, Klingon Edition
STOP IT. I'm going broke and I'm tired of taking my P4 apart!
-
What’s a P4, it’s Zaptool 101
-
Those look great, Zap 8)

-


So my #4 scalpel handle came in. I photographed and 3D modeled it in great detail.
I learned a few things that I may integrate into my holder.#1, The actual scalpel grip is just a simple set of slits, and doesn't have any feature that follows the middle area of the cutout. As best I can measure, the middle wider cutout is only to allow the blade to slide on easier, the position of the middle cutout doesn't actually equate to any sort of stop. Instead, it is where the blade is designed to start bending.
#2 The blade bend at the handle. I knew this already, but this handle uses a simple angled ramp to achieve this, I will emulate this, as I realized the bump idea allows the blade to tilt left/right on the bump.
#3 The angled back edge of the blade is actually quite important, it is the primary stop to allow you to exert pressure on the blade. i will have to keep this area with a tight tolerance to the blade.About tolerances. These things seem to be designed with zero or nearly zero tolerances. For example, the small end of the cutout in the blades measure 2.00mm. And that is also the exact width (as best i can determine) of the middle support in the handle.
The length of the cutouts in the blade is 24.24mm, the length of the oblong receiver on the handle is just 24.15mm, leaving just 0.11mm of gap for the blade. Finally the regular blades are 0.40mm thick, and the slot is just 0.50mm wide. This means this handle can't even hold the 0.5mm blades unless you want to jam them on just once.Since my part is sintered and shrinks a bit, I have to oversize carefully. (As Metropolicity already did in his design). Just do a few design tweaks and I can get to prototyping.
-

(Not a photograph!
)Also, the prototypes have been ordered.
-
Great job, Zap
They look really great

-

@ZapWizard said:

(Not a photograph!
)Also, the prototypes have been ordered.
-
@Dutch_Tooler said:
Thanks guys :D
Good news on the tweezers holder Zap, looking forward to that
I discovered I need to make a small notch in the file to allow the plier head tooth to engage the handle
Notch made in the file and in the saw blade (where the screw threads point) now allows the pliers to engage the handles properly with tool stored.

-
Great job on that, DT

-
@Dutch_Tooler said:
Notch made in the file and in the saw blade (where the screw threads point) now allows the pliers to engage the handles properly with tool stored.I didn't need the notch for my setup. I'm thinking I shortened the file a little more, past where your notch is.
-
I bought 4 of the one handed opening assist parts. I installed one into each of the knife blades. They fit well but would not stay in. A simple solution for me was to fill the back side with white epoxy and they haven't come loose since. A very ergonomic addition to my P4. Am probably going to buy the bit driver very soon. Thanks Zap!
-
@Slygrin said:
I didn't need the notch for my setup. I'm thinking I shortened the file a little more, past where your notch is.Probably. I thought of that too but I didn't like the thought of taking off more blade length than absolutely necessary. Plus the resulting hook might come in handy for picking up things out of reach of your hands ;)
Pic shows P4 on standby at the grill...

-
??? Hi guys, so the stars finally aligned, my P2 came back from warranty for the second time and the pliers where problem free! So I have gone to install the bit exchanger and blade exchanger... Well that was 3 hours ago. The problem I'm having is with the little plastic piece which covers and holds the magnet in place and how it contacts the base of the spring (part which sits around the magnet).
From factory the springs sit just to either side of the plastic cover part, but when installing the thicker blade exchanger the spring is pushed over the top of the plastic piece, meaning the bottom claw(?) Of the spring is floating above the magnet, causing me to be unable to get the pin even nearly lined up :-[ I have tried all sorts, but each time it's deforming the plastic piece more, and every time I can get the screw tight, the whole frame is out of wack because it's pushing the magnet cover all over the shop. Has anyone found this, or better yet, found a solution to this? Getting rather frustrated and feeling a bit stupid
-
@Dutch_Tooler said:
Probably. I thought of that too but I didn't like the thought of taking off more blade length than absolutely necessary. Plus the resulting hook might come in handy for picking up things out of reach of your hands ;)Pic shows P4 on standby at the grill...
Great picture! I decided to just shorten the file and not the saw. I use the file 90% of the time. I also carry a Surge, rotate it with the P4. I can always use the longer blades when needed on the P4, I just have to put the file back in to close it or leave it empty.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login