ZapWizard's Leatherman Free P4 Mods
-
Great job, Zap
They look really great

-

@ZapWizard said:

(Not a photograph!
)Also, the prototypes have been ordered.
-
@Dutch_Tooler said:
Thanks guys :D
Good news on the tweezers holder Zap, looking forward to that
I discovered I need to make a small notch in the file to allow the plier head tooth to engage the handle
Notch made in the file and in the saw blade (where the screw threads point) now allows the pliers to engage the handles properly with tool stored.

-
Great job on that, DT

-
@Dutch_Tooler said:
Notch made in the file and in the saw blade (where the screw threads point) now allows the pliers to engage the handles properly with tool stored.I didn't need the notch for my setup. I'm thinking I shortened the file a little more, past where your notch is.
-
I bought 4 of the one handed opening assist parts. I installed one into each of the knife blades. They fit well but would not stay in. A simple solution for me was to fill the back side with white epoxy and they haven't come loose since. A very ergonomic addition to my P4. Am probably going to buy the bit driver very soon. Thanks Zap!
-
@Slygrin said:
I didn't need the notch for my setup. I'm thinking I shortened the file a little more, past where your notch is.Probably. I thought of that too but I didn't like the thought of taking off more blade length than absolutely necessary. Plus the resulting hook might come in handy for picking up things out of reach of your hands ;)
Pic shows P4 on standby at the grill...

-
??? Hi guys, so the stars finally aligned, my P2 came back from warranty for the second time and the pliers where problem free! So I have gone to install the bit exchanger and blade exchanger... Well that was 3 hours ago. The problem I'm having is with the little plastic piece which covers and holds the magnet in place and how it contacts the base of the spring (part which sits around the magnet).
From factory the springs sit just to either side of the plastic cover part, but when installing the thicker blade exchanger the spring is pushed over the top of the plastic piece, meaning the bottom claw(?) Of the spring is floating above the magnet, causing me to be unable to get the pin even nearly lined up :-[ I have tried all sorts, but each time it's deforming the plastic piece more, and every time I can get the screw tight, the whole frame is out of wack because it's pushing the magnet cover all over the shop. Has anyone found this, or better yet, found a solution to this? Getting rather frustrated and feeling a bit stupid
-
@Dutch_Tooler said:
Probably. I thought of that too but I didn't like the thought of taking off more blade length than absolutely necessary. Plus the resulting hook might come in handy for picking up things out of reach of your hands ;)Pic shows P4 on standby at the grill...
Great picture! I decided to just shorten the file and not the saw. I use the file 90% of the time. I also carry a Surge, rotate it with the P4. I can always use the longer blades when needed on the P4, I just have to put the file back in to close it or leave it empty.
-
@Rocket surgery said:
??? Hi guys, so the stars finally aligned, my P2 came back from warranty for the second time and the pliers where problem free! So I have gone to install the bit exchanger and blade exchanger... Well that was 3 hours ago. The problem I'm having is with the little plastic piece which covers and holds the magnet in place and how it contacts the base of the spring (part which sits around the magnet).
From factory the springs sit just to either side of the plastic cover part, but when installing the thicker blade exchanger the spring is pushed over the top of the plastic piece, meaning the bottom claw(?) Of the spring is floating above the magnet, causing me to be unable to get the pin even nearly lined up :-[ I have tried all sorts, but each time it's deforming the plastic piece more, and every time I can get the screw tight, the whole frame is out of wack because it's pushing the magnet cover all over the shop. Has anyone found this, or better yet, found a solution to this? Getting rather frustrated and feeling a bit stupid
Good to have a functional P2 now

Yes, I had a similar problem - not enough space left for the plastic bit between the springs, seeing that there are now only three implements between them. I ended up leaving the plastic bit out. One could maybe shorten it and reprofile the shortened end but I decided it wasn't worth the hassle. It seems that the magnet still sits where it should even without the plastic bit. -
@Rocket surgery said:
Has anyone found this, or better yet, found a solution to this? Getting rather frustrated and feeling a bit stupid
I haven't modified my P2 as much, but I can imagine what your talking about. The plastic bit does nothing more than make the magnet surface a bit easier to clean. The magnet itself is held in place by the springs.
You could always trim off a tiny portion of the plastic where the spring now hits.
In other news Shapeways has finally finished producing the Scalpel holder prototypes, which are now in the mail. Metal parts now take a month even when paying for rush production. That sucks as each time I need to tweak the design it takes 5 weeks to get the new parts to confirm the changes.
-
Love your work here, ZapWizard. I've been modifying some Free parts by hand, and I designed and printed my own spacer for the T4 to hold a custom set of tools, as well as a few Leatherman bits with a driver built in. I'm happy to share the design with anyone that's interested, but it takes a lot of work to use, because you have to cut down the magnet and pivots by hand.
I'm starting a new build based on the T2, and I'm keeping the factory dimensions for pivots and magnets. I've ordered your 4mm bit driver to replace the two 'thick' tools, since it's better than anything I've come up with. In my existing T4, I use a scalpel blade on a ground-down awl tool, which is the standard 'thin' size for the Free tools. Any chance you'd be able to do a thinner version of your scalpel holder without the thumb tab? That way I could replace my terrible, hand-ground version. :)


-
Very cool T2 mods! They did waste a lot of space on that thing with plastic.
If the scalpel holder works out (the blade holding profile) I could alter the rest of the design to make it fit in place of a thin tool.
A #3 profile holder may be a good project for the smaller T2 or T4. -
Yep, a #3 blade would be perfect, as that's what I've been using in my T4/T2 stuff. I do a fair amount of tinkering in Fusion and 3d printing in general, so if I can be of any help, definitely let me know!
-

Teaser image!
The prototype scalpel holder finally arrived.
(The damn UPS Mail Innovations delivery took 12 days)
I just have a few tweaks to make to the design. As usual I will still order a 2nd prototype before selling. So expect another 4-6 weeks till is is available to order.The great news is that the slot profile works well. The slot came with a bit of gunk still stuck in the slot. The good news is that thinnest dremel grind off wheels happen to be exactly the right size to clear the slot. Just a few tiny hits from the dremel and the slot allows the blade to slide on perfectly. The 0.6mm blade I have (60XT) doesn't want to fit, but that isn't a big deal.
I did also have to grind off a bit of the back stop of the blade. I need ~0.7mm more clearance in that area. The thumb tab also needs improving.
The term "scary sharp" applies. No I didn't cut myself (yet), but its weird how the scalpel blade feels much more dangerous when deployed compared to the regular blade. Part of that is also the fact that the pointed tip of the blade is exposed with the slightest deployment angle. So I am going to recommend that anyone who installs this use a holster, and not just the tool in their pocket or belt clip.
-
Looking good, Zap 8) Glad to hear that the prototyping is going well and it is almost complete

-
Fantastic work! Now replace the handles and pliers!

-

This doesn't even feel legal. >:D

I have finished all the tweaks to the design. Lots of small things you can't see, such as moving things by 0.1mm to get just a slightly tighter fit.
The biggest change is the scalloped curve in the thumb tab to increase the grip while opening. Another larger change is less material near the back outside edge of the blade, this allows you to get a better grip with pliers when removing the blade.I will order the 2nd prototype, and paid extra for shipping so I don't have to wait so long.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login