Free P4 pliers stiffness after moderate or heavy use
-
Glad to read about Sam's method which is fairly interesting. Also Mcfal12's method(which helped in my case when I 'firm hand shake' my P4 and showing first sign of binding) and NetsNJ's method are also both great.
I am sure LM is a stand up company, and if you could get it serviced, probably best to take advantage of that warranty program. Otherwise, all the ingenious solutions here are real life savers.
-
For what's it's worth, my P2 binds, my P4 doesn't. Some of my waves do, some don't. I'm super curious about the cause. Just got some PST IIs in the mail. Squeeze as hard as you want - no flex, no binding.
-
@AimlessWanderer said:
If I had to guess (and without taking an angle grinder to one, that's all I can do), I'd say it's due to the shave of the void that the plier rivet is formed into. Specifically, having too obtuse an angle at the bottom of the void.Excuse the quality of the attached sketch, it was just freehand. Note on the top illustration, the void is a 90o countersink. This leaves a 45o angle on rivet and plier head from the plane on which the two halves of the plier head rub. Squeezing the pliers forces each half of the plier head in a shear action onto either side of the rivet, wedging the upper plier half between the lower plier half, and the 45o angle of the rivet head. At 45o or larger, the head shouldn't lock.
On the second illustration, a 120o or larger countersink, would leave a 30o included angle or less between mating plier faces and the rivet head. The smaller that angle, the more it will lock up like a Morse taper. Polishing it won't help either. It will just increase the amount of surface area in contact, and possibly make it worse - unless the vertical play is greater than the horizontal play.
This is all purely speculative, and one would hope that a 30+ year manufacturer of pliers wouldn't make such a fundamental error, that the numpty typing this, who's never made a pair of pliers in his life, can spot.

So, as I say, this is complete guesswork, and I might be barking up a lamppost, mistaking it for a tree. If however I am right, this needs a fundamental redesign. As for fixing pliers you already own, the only solution I can think of is to stretch/sprain the rivet pin, so those two faces are slightly too far apart to jam up in. However, this would also adversely affect wire cutting, particularly on fine stranded wire.
This is my first post here, so hi
I have a P2 arriving the coming week and started reading up which brought me here.
Reading your post I think your theory is spot on, explains why when even squeezing another tool like the surge I have here with alot of force, the pivot is tightened (presumably by being pushed out by a miniscule amount), pulling the plier jaws together either making them a little snugger, all the way to the P2/P4 problem your facing of locking up tight. It explains why leatherman marketed the P2/P4 as the "strongest pliers ever", and it would also explain why either hammering or working the tool by wiggling the handles/jaws, or twisting would reseat the pivot and give you the looseness back. The difference is with the surge I have it make a full on death grip, but the free series it doesn't take much, and seems to lock up much tighter on the free series.
What I'm not sure about is when you said polishing would make it worse rather than better due to contact area. In my mind it's true... But only half the time. From my understanding lapping the inside of the pivot just working it wouldn't serve as to wear down anything productive all the time it's freely moving. What I'm suggesting is a gradual improvement IF you are lapping when it's jammed up and stiff to open/close. The theory being that it will be grinding the riveted edge of the pin where it jams rather than the centre points where it's already loose enough to close with ease. I THINK it would make for a little more slack, and taking significantly more force to jam up (or ideally, alot of force to get slightly snug).The best way I can think to test this is (if someone wants to jump in and check before mine arrives) to clamp the tool in a vice with the fixed pivot side (fixed to and moves with the jaw) is unsupported, with a socket or ring around it supporting the jaw, but nothing touching the pivot.
On the other side of the vice, there should be something hard (a nut maybe?) putting all the pressure solely on the moving side of the pivot (the jaw moves independent to this side, and rotates around it) and not on the jaw surrounding.
When the vice is loose one side of the pliers will be freely opening and closing the unsupported jaw, but when tightened the pliers will lock up (again that's if my theory is correct, in which case only tighten the vice untill the pivot gets tight, don't crank it like your life depends on it!).If they do lock up (and the theory checks out), then I would put lapping compound in and work the tool, which should grind the contact of the riveted side of the pivot against the jaw. I would then work it untill the action started to get somewhat looser. Once the jaw is moving ok, I'd then flush the compound out however was appropriate and oil up with a thin lube.
After this I would go BACK to the vice (hey, I didn't say it would be quick) and reverse the way it was being held, putting the spacer around the side of the pivot the jaw moves around, and the nut against the fixed side of the pivot. Then tighten the vice up to around the same pressure it took initially and (if my theory holds true) there should be noticeable improvement in stiffness when cutting wire/nails/your ex's break cable. (To clarify - that was a joke, you should never cut nails with your leatherman)That's the idea atleast, and if my P2 jams up, I will be trying. Sorry for the long read

-
Welcome to the forum!
Very intriguing read!
-
Thanks for the warm welcome!
Re-reading my post, I'm noticing quite how bad my grammar and explanations are - I apologize if it causes any undue confusion. I would edit it to make more sense but can't seem to see the button

In order to clarify what I'm saying please read on -In the vice, the side of the pliers with the pivot fixed in place to the jaw should be supported, but the pivot shouldn't be. I'm thinking a socket larger than the pivot with some tape to avoid scuffing would work well.On the other side, where the plier jaw freely rotates around the pivot, the vice should only be touching the pivot and not the jaw it's self. I would think a small nut (again with some tape to prevent scratches), or the end of a wooden dowel would do the trick nicely.
This means that when the vice is loose the pliers should open and close freely.If my theory is correct then tightening the vice should snug up the pivot and make it stiff in the same way cutting a nail would. If that's the case then mixing a little lapping compound/polishing powder (if possible a medium grit) and alcohol/acetone/thin oil will make for a lapping liquid of sorts, which when applied will allow the compound to fill any gaps in the pivot area. While the vice is still tight and the compound has been put in, I would start to open and close the pliers (even if that meals putting a length of pipe over each of the plier jaws for more leverage) in order to get the compound to do its job and grind/polish the really tight areas.
Hope that made more sense - I need to learn to proof read an awful lot more!
-
Mrs. Fool gave me a P2 for my birthday yesterday. (REALLY wasn't expecting it) I too have a problem with the pliers getting hard to open after using some pressure on them. I'm thinking about sending them back. My question is this,
When you send something back do you make a reference about this forum, and/or about the same issues the other members are having with them?
-
Congrats on the new tool
sorry about the problems though
You can always reference th forum like that but I am not sure if they pay attention to that in the Waranty Dept. or not
Never hurt to link them to threads like this though
That way they can't say they don't know about the problem (well at least after they have read this thread or similar ones
) :D -
Thanks Poncho, I think I will reference this forum/thread just to remind them that there is a following and a tight MT family here. I also did not know what MTO thought about the reference.
-
After a whole lot of working (covid meant alot of free time, atleast 10 hours and a few blisters) with the pilot pivot dry (no lubricants), and after a good squeeze I got a whole 0 progress. so being stubborn as an ox I tried everything I could find. Including but not limited to; lube, polishing compounds, the hammer trick, my vice idea, more dry working with the pliers stiff to work down any weird bits inside when tight (total working between 18-20 hours not including breaks to change movie). All I have successfully done is avoid needing a gym.
I'm afraid this one has beaten me. On the plus side I sucked up my pride and sent it in for warranty (in the UK they don't repair, they just give you a new one). On the negative side the new one is 2-3x as bad as the first (best I could capture a picture to sum it up). Sorry to get anyone's hopes up with a fresh set of eyes. Will post an update when the third new tool arrives..jpg)
-
That well and truly smurfs. :(
-
Bummer

My P2 went in for warranty before COVID lockdown. Local distributor eventually called me 3 weeks ago to ask what the problem was...had to share the video I did of the thing locking up. Oh...OK, we’ll replace it. Got the new one last week. Better. Still binds a little, but no more than other LMs and I can live with it. But it’s not getting much love from me. :( -
Im on my second p2 and the warranty replacement is worse then the first. My p4 is great tho but the p2s pliers just bind up so stiff. Anyone have any ideas on how to fix this minus sending it in again. P4 is great so some seem to work and others just bind.
-
@Krayakin87 said:
Im on my second p2 and the warranty replacement is worse then the first. My p4 is great tho but the p2s pliers just bind up so stiff. Anyone have any ideas on how to fix this minus sending it in again. P4 is great so some seem to work and others just bind.Sorry logged into wrong account. Pls reply to this one if anyone has any ideas.
-
Sorry to hear this

I really dint use my P2 much as I have other options I am much more fond of

Hopefully someone will be along that can help

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login