Free P4 pliers stiffness after moderate or heavy use
-
Thanks for the warm welcome!
Re-reading my post, I'm noticing quite how bad my grammar and explanations are - I apologize if it causes any undue confusion. I would edit it to make more sense but can't seem to see the button

In order to clarify what I'm saying please read on -In the vice, the side of the pliers with the pivot fixed in place to the jaw should be supported, but the pivot shouldn't be. I'm thinking a socket larger than the pivot with some tape to avoid scuffing would work well.On the other side, where the plier jaw freely rotates around the pivot, the vice should only be touching the pivot and not the jaw it's self. I would think a small nut (again with some tape to prevent scratches), or the end of a wooden dowel would do the trick nicely.
This means that when the vice is loose the pliers should open and close freely.If my theory is correct then tightening the vice should snug up the pivot and make it stiff in the same way cutting a nail would. If that's the case then mixing a little lapping compound/polishing powder (if possible a medium grit) and alcohol/acetone/thin oil will make for a lapping liquid of sorts, which when applied will allow the compound to fill any gaps in the pivot area. While the vice is still tight and the compound has been put in, I would start to open and close the pliers (even if that meals putting a length of pipe over each of the plier jaws for more leverage) in order to get the compound to do its job and grind/polish the really tight areas.
Hope that made more sense - I need to learn to proof read an awful lot more!
-
Mrs. Fool gave me a P2 for my birthday yesterday. (REALLY wasn't expecting it) I too have a problem with the pliers getting hard to open after using some pressure on them. I'm thinking about sending them back. My question is this,
When you send something back do you make a reference about this forum, and/or about the same issues the other members are having with them?
-
Congrats on the new tool
sorry about the problems though
You can always reference th forum like that but I am not sure if they pay attention to that in the Waranty Dept. or not
Never hurt to link them to threads like this though
That way they can't say they don't know about the problem (well at least after they have read this thread or similar ones
) :D -
Thanks Poncho, I think I will reference this forum/thread just to remind them that there is a following and a tight MT family here. I also did not know what MTO thought about the reference.
-
After a whole lot of working (covid meant alot of free time, atleast 10 hours and a few blisters) with the pilot pivot dry (no lubricants), and after a good squeeze I got a whole 0 progress. so being stubborn as an ox I tried everything I could find. Including but not limited to; lube, polishing compounds, the hammer trick, my vice idea, more dry working with the pliers stiff to work down any weird bits inside when tight (total working between 18-20 hours not including breaks to change movie). All I have successfully done is avoid needing a gym.
I'm afraid this one has beaten me. On the plus side I sucked up my pride and sent it in for warranty (in the UK they don't repair, they just give you a new one). On the negative side the new one is 2-3x as bad as the first (best I could capture a picture to sum it up). Sorry to get anyone's hopes up with a fresh set of eyes. Will post an update when the third new tool arrives..jpg)
-
That well and truly smurfs. :(
-
Bummer

My P2 went in for warranty before COVID lockdown. Local distributor eventually called me 3 weeks ago to ask what the problem was...had to share the video I did of the thing locking up. Oh...OK, we’ll replace it. Got the new one last week. Better. Still binds a little, but no more than other LMs and I can live with it. But it’s not getting much love from me. :( -
Im on my second p2 and the warranty replacement is worse then the first. My p4 is great tho but the p2s pliers just bind up so stiff. Anyone have any ideas on how to fix this minus sending it in again. P4 is great so some seem to work and others just bind.
-
@Krayakin87 said:
Im on my second p2 and the warranty replacement is worse then the first. My p4 is great tho but the p2s pliers just bind up so stiff. Anyone have any ideas on how to fix this minus sending it in again. P4 is great so some seem to work and others just bind.Sorry logged into wrong account. Pls reply to this one if anyone has any ideas.
-
Sorry to hear this

I really dint use my P2 much as I have other options I am much more fond of

Hopefully someone will be along that can help

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login