Gareth's Sword Collection.
-
Staying with the British Army but shifting forward now into the 19th Century we come to the 1822 infantry officer's sabre. This was the replacement for both the 1796 sword and the 1803 sabre. It was the first of what are now known as the "gothic hilt" family of sabres which still survives in some parts of the service today. It has a three bar hilt with a clear bias for protecting the outside of the right hand and initially commonly had a small folding section on the inside over the thumb. As before this was intended to protect the uniform but unlike the 1796 it's small and reasonably tough. As the years went by this feature fell out of favour though was never regulated against. On this particular example we can see the Royal Cypher of Queen Victoria.
The blade on this is what is know as a "pipeback". You can hopefully see that it has what is intended to be a strong, stiff rib running the whole length of the blade. While the pipeback seems to have been successfully employed in some sabre designs it doesn't seem to work well on the 1822. It's certainly more flexible than they intended and, as we'll see later, it was updated in 1845. While this is technically a sabre by dint of having a curve to the blade it's so close to straight it almost makes no difference.



-
Gareth, this is a spiffing thread! Great photos and most interesting information. Thank you, and keep them coming!
Lähetetty minun SM-T515 laitteesta Tapatalkilla
-
@old Lefty said:
Gareth, this is a spiffing thread! Great photos and most interesting information. Thank you, and keep them coming!Lähetetty minun SM-T515 laitteesta Tapatalkilla
Cheer Lefty.
A few more to come. 
-
Moving up into the middle of the 19th Century and I have a few swords to look at still. :D First up we are going to look at the habit of giving out short "hanger" swords to infantry troops. These came in and out of favour for a few hundred years roughly depending upon what type of bayonet was being used with the soldier's musket or rifle. If you had a sword-bayonet then the additional hanger was superfluous, but if you had a spike bayonet then an additional sidearm was often seen as necessary.
One of the two main types of military hanger of the C19th was the "sabre-briquet" or simply briquet. Mostly associated with the Grande Armee of Napoleon they actually saw widespread use all across Europe for the next hundred years or so. They are so ubiquitous in fact they can be very hard to identify as to who used a particular sword or even when. Happily for me this briquet comes with some identity stamps. Thanks to a Swiss collector of Swiss arms I can tell you that this is a 1842/52 sabre-briquet issued in the canton of Zurich. Like many arms of the time though this was made in Solingen, Germany. Yes, this really is a Swiss Army...knife?

Made with a cast brass hilt and very solid steel blade these are hefty things to add to your kit and I doubt many soldiers really appreciated them. They were however used as a tool far more often than as a weapon. Weighing in at 1kg or 2lb 3oz you'd certainly know you were carrying it.



-
That kind of reminds me of this video about the French 1850's Arcelin Mousqueton with the biggest bayonet ever.
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
The video starts to talk about the saber bayonet at around 7:45.

-
@Chako said:
That kind of reminds me of this video about the French 1850's Arcelin Mousqueton with the biggest bayonet ever.- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
roll to 7:45 if all you are interested in is the bayonet.
Yes, that's definitely an extreme sword bayonet. :D Bayonets aren't part of my collecting and research but I do find it interesting how the much the cycle of socket/spike vs bladed/sword seems to have gone round and round.
-
Definitely related. :D
-
Bugger, I knew this would happen; I forgot one.

Lets rewind back to the later half of the 18th Century and look at the third of my smallswords. Over the century the trend was to smaller hilts and, most tellingly, the "finger rings". Interestingly these weren't intended for you to hook your finger through and hadn't been used that way since the days of the rapier. Shown below is the grip taught by every single smallsword fencing master, no matter the actual size of the rings. The hilt is made of gilt covered brass.
Different countries had broadly identifiable trends and schools of thought about fencing. So the Germans, Italians and French etc all had recognisable terminology and methods of fencing. The French school of thought in the second half of the C18th was for shorter and faster blades. Again we have some very nice chisel work on this triangular section blade.




-
That makes sense. I tried putting a finger in my Cold Steel version and found it quite limiting and uncomfortable. I had always assumed you placed a finger (or 2) in there. Thanks for clearing that bit up for me.

-
@Chako said:
That makes sense. I tried putting a finger in my Cold Steel version and found it quite limiting and uncomfortable. I had always assumed you placed a finger (or 2) in there. Thanks for clearing that bit up for me.
No worries. If you were holding a rapier you'd hook your index finger through the ring and it would give a nicely balanced grip for a longer, heavier blade for both cut and thrust play. However for a light blade and point play the pinch grip gives much finer control.
-
@Gareth said:
No worries. If you were holding a rapier you'd hook your index finger through the ring and it would give a nicely balanced grip for a longer, heavier blade for both cut and thrust play. However for a light blade and point play the pinch grip gives much finer control.Hahaha.... first thing I thought, these people must have had skinny fingers, but that makes a lot of sense.
-
-
Now that I see it, it makes a lot of sense. It prevents the blade from twisting on you..as the handles on these type of swords tend on the skinny side.
-
@Etherealicer said:
How could you, she is a beauty
:D
-
@Chako said:
Now that I see it, it makes a lot of sense. It prevents the blade from twisting on you..as the handles on these type of swords tend on the skinny side.Exactly. It also does a very good job of replacing your index finger with a very pointy bit of steel and most of us can point at what we want to hit. :)
-
@Gareth said:
Bugger, I knew this would happen; I forgot one.
Lets rewind back to the later half of the 18th Century and look at the third of my smallswords. Over the century the trend was to smaller hilts and, most tellingly, the "finger rings". Interestingly these weren't intended for you to hook your finger through and hadn't been used that way since the days of the rapier. Shown below is the grip taught by every single smallsword fencing master, no matter the actual size of the rings. The hilt is made of gilt covered brass.
Different countries had broadly identifiable trends and schools of thought about fencing. So the Germans, Italians and French etc all had recognisable terminology and methods of fencing. The French school of thought in the second half of the C18th was for shorter and faster blades. Again we have some very nice chisel work on this triangular section blade.
Interesting the pommel positioning in the wrist. Is it intended? To provide more stability to the blade? I only thought of it as a counter-weight, to position the balance point of the sword.
-
@pfrsantos said:
Interesting the pommel positioning in the wrist. Is it intended? To provide more stability to the blade? I only thought of it as a counter-weight, to position the balance point of the sword.Yes you are right, the pommel does indeed add weight to the hilt to help balance the sword. This hold is particular to the smallsword and helps index the sword and point onto the end of you arm so the blade makes a nice straight line with your forearm. Push your arm out and the sword point will be directly in line. Stabbing your opponent becomes as easy as pointing at them. ;)
-
I will also add this is only one grip, there are quite a few others. This one is the position of sixte.
-
Really enjoying this thread !

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login