Skary Skeletool October Challenge?
-
Powernoodle Day 7
Grab the flats or the corners? What say you?



-
[quote author=powernoodle link=topic=85570.msg2167567#msg2167567 date=1602071454]
Powernoodle Day 7Grab the flats or the corners? What say you?

The flats may have more contact but which ever way works best is the way... Great use and close up photo too!!


-
Day Seven.
Skele found some pipe to trim this morning....

-
<u>DAY 7</u>
Working from home today and I've been a slave to the work laptop ::)
First I drink the coffee, then I do the stuff!


-
Day 7

Slightly surprise to see rolls and dents on the blade after just a really short use. I know I have used the blade on cutting soda can and coconut open, but am slightly surprise to find the big roll on the serrated part. Still gonna think of a way to fix that, what do you guys think? I don't want to sharpen that large roll away, maybe a knife steel could roll that back?

I have used the SAK blade for similar coconut task, soda cans cutting and even gliding on steel coat hanger, but with the plain blade, I could literally bring it back to full sharpness within minutes on Sharpmaker. Part of the reason I always prefer PE over serrated edge.
-
@Nix said:
And Mrs Nix was not shy about pointing that out......

@Sos24 said:
If you soak in bleach or vinegar after carving it will help delay the decaying. Vinegar is preferred if wildlife might be around.Great tip! Thank you! I had fun carving one with SAK last year, but Mrs. put an order 66 on Mr Pumpkin since it was getting hairy within days.

(picture from last year)@5S Dude said:
Day sixSkele gave mr tractor some love this morning...

Man! gotta remember to get me a new knife!!

Awesome photos everyone!!

It is an impressive setup, and am pleasantly surprised to see the tool could take on this kind of torque too! Cool!
@powernoodle said:
Powernoodle Day 7Grab the flats or the corners? What say you?



I would say 'corners' because it is closer to the joint and the opening is less wide?

-
@comis said:
I would say 'corners' because it is closer to the joint and the opening is less wide?
Yeah, I think I'm a corner person too. You get just a little more bite, and less chance of slipping and cursing. Maybe.
@SurgeUk said:
Working from home today and I've been a slave to the work laptop ::)I've worked from home on a laptop since 1994. There are worse ways of earning a living.
But solitude is not for everyone. -
@comis said:
Slightly surprise to see rolls and dents on the blade after just a really short use. I know I have used the blade on cutting soda can and coconut open, but am slightly surprise to find the big roll on the serrated part. Still gonna think of a way to fix that, what do you guys think? I don't want to sharpen that large roll away, maybe a knife steel could roll that back?
I have used the SAK blade for similar coconut task, soda cans cutting and even gliding on steel coat hanger, but with the plain blade, I could literally bring it back to full sharpness within minutes on Sharpmaker. Part of the reason I always prefer PE over serrated edge.
I really prefer a PE to a SE. (99% of the time.)
The 420HC steel in the blade of my Skele seems a tad soft, to me, too. Takes a great edge, however.
-
The Edge on the scallops of the serrated sectIon must be a lot weeker than the plain edge due to having less than half the inclusive angle due to being ground shallower and only on one side.
They are normally protected from hard surfaces (when cutting on a board) by the points.
-
Day 7 of 30
Today Skeletool just hanged with me, played few times with it but no particular good use today.

Only Tools Matters
-
-
I found the hammer adapters on line and they are around $30.00 U.S. so too pricey for me, but I still think they are a great idea.
-
I would try to grab the flats because there is more surface contact and less chance to slip.
-
I use a pocket diamond coated sharpening rod to smooth out serrations but I use a very light touch so as not to gouge or cut too deep.
-
-
Day 07:
Pulled a big carrot out of the garden to have for lunch. Skele trimmed the tops off and cleaned up the ancillary rootlets.....

Then....a knock at the door......
Like a bad crime scene photo:

-
That carrot looks like a monster.
I’m guessing the spyderco is your new endura.
-
Edit: found it when I went to the website and not tapatalk.
Nice Endura, and
the zome versions Spyderco has look awesome

-
Hello Day 8
So I wanted to change the battery in the kitchen clock and of course I dropped it and broke the case that holds the battery in place.
I thought some duct tape would hold the battery in place firmly so would make proper contact and we would know what time it is.
That did not work so out with some small cable ties and she is all zipped up tight and working properly now.
Skele to cut off the excess bits of tie.
.jpg)
-
Nice repair!
-
Lots of great day 6 and day 7 pics, everyone

-
Day 7 of 30
Used the Skeley to sharpen a pencil again and used the cutters on the pliers to cut a plastic brick band


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

