Skary Skeletool October Challenge?
-
Powernoodle Day 9
*
Thank you, Colonel Comis, for the MTO magnet!* -
@powernoodle said:
Powernoodle Day 9
*
Thank you, Colonel Comis, for the MTO magnet!*

-
<u>DAY 9
</u>
It was a work day today (again) so no carrying, apart from at home.However, I needed to dismantle my work magnifier (used for checking documents up close) so, bought it home.
I used the small Phillips bit to remove the tiny screws and check the insides, which were a bit grubby :-[
A quick clean and some new AAA batteries and all was well again

Also, checked for a CX date code but, no joy; was this ever resolved (I read some previous posts about this)



-
@comis said:
I think you and I have the exact same model/variation!
So far all the serration I have seen are on the left side of the blade(possibly why Sos24 like it so much, a left handed blade), I kinda wonder do they have it on the other side? I think with a very acute angle, they could be quite good for feather sticking.Time does fly, and good job from you!

That's one handsome Skeletool!

@ReamerPunch said:
That Skele is seriously pretty.
Thanks Reamer and comis. I really like the Topo.
Comis you are right about the serrations just being on one side. They are also aggressive which has its advantages for cutting but as Nix discovered can also be bad.
-
Day 9 of 30
Today cutted open zipties with blade. Also used pliers to bend nails.

Only Tools Matters
-
It is hard to believe we are almost a third of the way through this challenge. I haven’t had as much time as I usually do to follow and reply lately, so I feel a little bad. But now that I am having a little time to go through, I am liking the variety of uses and discussion, as well as the pics of course.
-
Day nine
Flat head Friday! Hope everyone’s havin a great Friday...


-
Day 9
my mum broke the glass from a bulb when trying to change it so i grabbed my skeley and a head torch to go over an fix it for her. also while there i used the large flat bit to prod the rubber seal back in place around the door of her washing machine.

-
Hi
Just a reply to Comis about the roll of concrete.
I am a concrete technologist by trade and often they need to drill holes in a wall or slab to allow cables etc to pass through. For larger diameter holes it is easier to drill a core than to drill big holes. That roll is such a core
I like to keep the cores as I can then see how my concrete mix has turned out and sometimes they are just pretty. Most of you will think it very sad that I find concrete pretty but hey it pays the bills and lets me buy more MTs.
That roll is a core from some floor somewhere and cannot remember why I have kept it.
They do come in handy though if you do not have a stand for your soldering iron and you do not want to burn the carpet or desk.
-
@Pauldmmwc said:
Hi
Just a reply to Comis about the roll of concrete.
I am a concrete technologist by trade and often they need to drill holes in a wall or slab to allow cables etc to pass through. For larger diameter holes it is easier to drill a core than to drill big holes. That roll is such a core
I like to keep the cores as I can then see how my concrete mix has turned out and sometimes they are just pretty. Most of you will think it very sad that I find concrete pretty but hey it pays the bills and lets me buy more MTs.
That roll is a core from some floor somewhere and cannot remember why I have kept it.
They do come in handy though if you do not have a stand for your soldering iron and you do not want to burn the carpet or desk.
Im weird and love the look of concrete, next year hopefully I want to get a new path poured down and around my garden. I also love the look of brutalist architecture.
-
Very nice pics again today

-
Day 9 of 30
Just a quick pic today


-
@Pauldmmwc said:
Hello day 9.
Bit of a fiddly job making a speSmurfpillst battery charger from a usb phone charger cable. The Skele to do the roughcuts and a very underated tool the Squirt E4 to do the fine work. 2LMs for one job must be happy days .
That is a cool use. I’ve seen emergency phone chargers using 9v and AA. I was tempted to make one just to see ho well it worked.
-
@chip said:
Day 9
my mum broke the glass from a bulb when trying to change it so i grabbed my skeley and a head torch to go over an fix it for her. also while there i used the large flat bit to prod the rubber seal back in place around the door of her washing machine.

Good use. I also have and like the Olight H1 headlamp.
-
Thanks to the generosity of 5S Dude, the Skeletool Challenge giveaway just got even better, instead of one there will be two.

In addition to the choice of Hammer head, 5S Dude is donating a 1/4"-Hex to 1/4" square drive (bit driver).

So when you post your entry photo indicate if want to be in both drawings. -
Hello day 10
It was a day of leisure mostly with not much chores done so today's pic is one of Skele at rest whilst I attempt to quench the unquenchable .
Have to keep trying though.



-
@Sos24 said:
Thanks Reamer and comis. I really like the Topo.Comis you are right about the serrations just being on one side. They are also aggressive which has its advantages for cutting but as Nix discovered can also be bad.

@5S Dude said:
Day nineFlat head Friday! Hope everyone’s havin a great Friday...


GeForce! Are we putting in a serious graphics card for some game playing?

@chip said:
Day 9
my mum broke the glass from a bulb when trying to change it so i grabbed my skeley and a head torch to go over an fix it for her. also while there i used the large flat bit to prod the rubber seal back in place around the door of her washing machine.

Great use
, hope she didn't hurt her hand and all is right. -
@Pauldmmwc said:
Hi
Just a reply to Comis about the roll of concrete.
I am a concrete technologist by trade and often they need to drill holes in a wall or slab to allow cables etc to pass through. For larger diameter holes it is easier to drill a core than to drill big holes. That roll is such a core
I like to keep the cores as I can then see how my concrete mix has turned out and sometimes they are just pretty. Most of you will think it very sad that I find concrete pretty but hey it pays the bills and lets me buy more MTs.
That roll is a core from some floor somewhere and cannot remember why I have kept it.
They do come in handy though if you do not have a stand for your soldering iron and you do not want to burn the carpet or desk.
That's pretty cool! Must be one heck of a drill to core out a roll like that. Maybe even the same kind we see on bank heist movie? :D
Just a quick pic today


Nice find!
@Sos24 said:
Thanks to the generosity of 5S Dude, the Skeletool Challenge giveaway just got even better, instead of one there will be two.
In addition to the choice of Hammer head, 5S Dude is donating a 1/4"-Hex to 1/4" square drive (bit driver).

So when you post your entry photo indicate if want to be in both drawings.Thanks 5S dude and Sos24, very generous of you guys!

-
Day 09:
Skele's cutters got used to snip some fishing line. And did well, too.

Later, the main blade got used to cut some kevlar cord and some paracord. Did well, although kevlar cord is tough stuff.

-
Day 9
A little late but forgot to post earlier. Skeletool helped open some Halloween candy. I had to test out the bag to make sure their good.

In reality I like the small pieces, because a little piece is usually enough.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
