Knot in October GAW
-
-
-
-
-
-
@Sos24 said:
I can see why you would say that, because they are very similar, but there is another key difference.In the clove hitch the two ends are side-by-side, but in the constrictor knots the ends overlap a d apply pressure to each other.
Maybe the best way is visual. Here is a picture of the clove hitch, single constrictor and double constrictor (L->R) before tightening.

You can see with the constrictor knots, each end is overlapped by the other end where it exits/enters the knot. Because of these overlaps a pull on either end tightens the knot but also presses the opposite end down into the object. The pressure on the opposite end means makes it highly unlikely that the knot will loosen, especially if either end is under tension.
I hope this makes sense, because despite understanding it in my head, Iโm not sure I explained it well.
Really nice and usefull knot Sos!
-
@enki_ck said:
Here goes my 2nd entry.One would think I entered more often as I seem to have a variation of a knot or tying it on almost every knot shown.
Sorry about that. 
Now, I mentioned the figure 8 knot many times over already here in the thread as it's the most important and reliable knot I know and use. And to my great astonishment no one has yet used it.
There are many variations and iterations of it, and I could probably post all my five entries with just those, but we'll see what others have on their minds. 
This entry is actually two knots, as it combines the figure 8 with another woven in figure 8. As I used a knot for connecting two ropes the first time around, I decided to continue with the tradition.

A double fisherman can be used to connect two ropes of same or different diameters safely. The figure 8 can't. It's only appropriate for connecting two ropes of same diameters. So 10mm rope to 10mm rope and so on. If you use different diameter ropes, the thinner one could slip out, and that's BIG safety hazard. Now, why would one use it then? Cause you can if you make a figure 8 on your first rope, connect the two ropes and also add an attachment point to safely pass a knot on the rope.

So here goes...
Take a bite of a rope and wrap it around itself as shown in the pictures, one wrap around makes a figure 6, also a good and simple knot, two wraps make a figure 8, and if you'd continue passed that and add another wrap before you passed the bite through the hole, you'd make a figure 9. but that's for a knoter knot story

Pull it tight and you have yourself a very safe figure 8. The working end of the rope should always be on the top of your knot so you tighten it even more when under load. And it is important to make it look nice, so no overlaps and crossed threads, every overlap you make reduces the load baring capabilities of a knot by about 25%. See how pretty the knot can look like?
Now, to connect the second rope, you loosen the figure 8 a bit, and pass the tail of the second rope through the two strands, follow the two strands all the way till you've repeated all the wraps around the knot. Tighten it and you have yourself a nice and useful knot.

Nice, beautifull and very usefull knot!
-
@Huntsman said:
OK - I really should post earlier in the week..... Or at least post immediately after I took my photos ..... because.......I took photos of my Figure of Eight yesterday when I took my Yosemite Bowline piccies - Ready to post today .....
But of course enki
knicked my knot ..... Knot funny 
Anyway seeing as I had the pics already I will post them and say a few words about the use of the knot.
It's slightly different from Enki's Figure 8 - No bight - But essentially still a double threaded Fig 8.So this is how ***nearly all ***UK crag climbers tie into a rope..... See diagram/piccie.
- You take the rope and tie your first Fig 8 about 1 metre from the end of the rope
- You then thread the free end through the waist loop and (very importantly) the groin loop of your climbing harness
- You then feed the free end back around the Fig 8 following the line of the rope all the way - as you see in the diagram/piccie
- And probably ...... as always ,,,,,,, finish off with a stopper knot - Which I do not show

Perfect!!
As mentioned earlier this knot takes longer to tie than a Bowline, is way harder to undo under strain ie if you fell on it
But is easier to tie, less chance of a mistake and much easier for your partner to check .......as you can see !!I will say a few more words about the Fig 8 when I make my post for this week!!

Very nice!
-
-
OK - Here is my post for Week 2.
I am not sure if it is even allowed, as we've probably seen it or something like it already - And it is possibly even too simple!!!

But maybe my explanation will allow it - We'll see what Mrs Nix says!!So this knot is about joining two ropes together

We've already seen a few ways of doing this - interwoven Fig 8; Double (or single) Fisherman's ...... Which I loveSo why this one ??? ..... Why would I knot use the other two ??? ..... And why is this one different. ???

Well this is a knot I use to join two ropes together for an abseil.
When you climb/mountaineer you usually use one (or two) 50m rope(s) - When you abseil you always go down a double rope.To abseil:
-
You thread the rope through some sort of attachment point (or tat) to the rope's mid-point
-
You abseil down
-
You pull your rope through ready to carry on with the route (eg the next abseil !)
If you have one rope you can abseil **25m **- But if you have two you can join them together and abseil 50m which of course is better and quicker
And this is how I was taught to join them with a **simple overhand knot! **

So why knot one of the more substantial - and seemingly safer - other knots ???

Well
[list type=decimal]* This knot is so simple and **quick **to tie (time can be a very critical consideration when climbing)-
It is a very low profile/sized knot and this can be very important when pulling your rope back down from the attachment point - It the knot gets stuck somewhere - eg in between two rocks you have got real problems - Basically you have to climb back up the rope to try and free it which is very dangerous! The low profile of this knot is very handy in this regard
-
This knot, despite its simplicity, is **bomb proof **- It cannot be undone - The more you load it the tighter it gets - Try it at home - And of course I have entrusted my life with this knot!
-
The safety aspect would also be true of the Fisherman's - But of course it is a lot more bulky - And believe it or knot there could be a problem with the Fig 8 in this regard - See my next post!!!
-
-
Ralf, I think we could be having a discussion on this one. We call that knot a figure 6 knot here. And yes, it's a very tight knot, the only problem I see with it if abseiling on it is that the strands are loaded against the direction of the knot and you are essentially "breaking" the knot when you put it under load if abseiling on a single strand of rope if I understand correctly how you described the descent on a single rope.

A water knot like you use to make a webbing sling would load the rope better, but would probably be more prone to slipping out. However I don't have experiance with double rope techniques and trust you climbers know your stuff better than us dirty underground dwellers and our SRT
Looking forward to your next post and to hear the problems with the interwoven figure 8. Anything other than the danger of rope slipping if the ropes are of different diameters? It's of course bigger than an overhand knot, especially if you tie it with the way I did through an existing figure 8, and if using it for a double rope technique the direction of the strands would be all wrong, is this what you were thinking of?
-
-
@Huntsman said:
OK - Here is my post for Week 2.Spoiler:
I am not sure if it is even allowed, as we've probably seen it or something like it already - And it is possibly even too simple!!!
But maybe my explanation will allow it - We'll see what Mrs Nix says!!So this knot is about joining two ropes together

We've already seen a few ways of doing this - interwoven Fig 8; Double (or single) Fisherman's ...... Which I loveSo why this one ??? ..... Why would I knot use the other two ??? ..... And why is this one different. ???

Well this is a knot I use to join two ropes together for an abseil.
When you climb/mountaineer you usually use one (or two) 50m rope(s) - When you abseil you always go down a double rope.To abseil:
- You thread the rope through some sort of attachment point (or tat) to the rope's mid-point
- You abseil down
- You pull your rope through ready to carry on with the route (eg the next abseil !)
If you have one rope you can abseil **25m **- But if you have two you can join them together and abseil 50m which of course is better and quicker
And this is how I was taught to join them with a **simple overhand knot! **

So why knot one of the more substantial - and seemingly safer - other knots ???

Well
[list type=decimal]* This knot is so simple and **quick **to tie (time can be a very critical consideration when climbing)- It is a very low profile/sized knot and this can be very important when pulling your rope back down from the attachment point - It the knot gets stuck somewhere - eg in between two rocks you have got real problems - Basically you have to climb back up the rope to try and free it which is very dangerous! The low profile of this knot is very handy in this regard
- This knot, despite its simplicity, is **bomb proof **- It cannot be undone - The more you load it the tighter it gets - Try it at home - And of course I have entrusted my life with this knot!
- The safety aspect would also be true of the Fisherman's - But of course it is a lot more bulky - And believe it or knot there could be a problem with the Fig 8 in this regard - See my next post!!!
I was knot expecting an overhand knot for that. :ahhh
-
I went through this again.

I already knew the bowline, hangman's knot, single and double fisherman's, clove hitch.
I have learned and am able to tie from memory the Alpine Butterfly, the handcuff knot, break-away lanyard, single and double constrictor.I am impressed with the constrictor knots. Talk about tight. wow. :ahhh I wish someone had taut me these earlier.
Tightening it reminds me of the movie Anaconda. It really looks like the cord is alive. Thanks, Sos24!
And we have three more sets of knots coming! Can't wait!

-
-
@ReamerPunch said:
I am impressed with the constrictor knots. Talk about tight. wow. :ahhh I wish someone had taut me these earlier.
Tightening it reminds me of the movie Anaconda. It really looks like the cord is alive. Thanks, Sos24!
A slipped constrictor knot is just as tight as a regular one, but much easier to untie.

-
@enki_ck said:
Ralf, I think we could be having a discussion on this one. We call that knot a figure 6 knot here. And yes, it's a very tight knot, the only problem I see with it if abseiling on it is that the strands are loaded against the direction of the knot and you are essentially "breaking" the knot when you put it under load if abseiling on a single strand of rope if I understand correctly how you described the descent on a single rope.
A water knot like you use to make a webbing sling would load the rope better, but would probably be more prone to slipping out. However I don't have experiance with double rope techniques and trust you climbers know your stuff better than us dirty underground dwellers and our SRT
enki, you've echo'ed my very first thoughts.I've always avoided the overhand because, once loaded, it can be hard to untie. As pictured above, the load on the two joined strands would be pulling the knot apart. I don't know about the overhand, but with a Figure 8 I have been taught to never tie two lines together with a Figure 8 like this when the load will be along both lines. No tonly is the knot being pulled apart, but it is also much weaker (I've seen testing on this.)
To the contrary, a water knot (which has knot been entered in the contest so far.....
) is a relatively strong knot, and might be preferred for joining two tapes.I have to defer to Huntsman's experience here, but for anything other than a simple loop, the two-strand overhand scares me.
Still...it is a knot! And can be useful! It counts!
-
@ReamerPunch said:
Nice monkey fist!
I made one too. I finished it with a Friendship knot.
I was thinking of entering the monkey fist in here, but decided against it. I could argue it is useful, as a weight, fidget, or for self defense, but it is mostly decorative.

The knot I tossed out there is knot a Monkey fist.....
(bet ya a beer that Sos24 knows what it is....)And I could argue that both our knots are useful.....
They didn't come about by accident! 
-
-
Huntsman's post prompted me to do a little research into the Overhand knot when used as a bend between two lines.
Thanks, Huntsman!


Wiki has a nice article about this knot here: Offset Overhand Bend
In that article, I was reminded that this knot has been called the "European Death Knot" or EDK because its use has been associate with several climbing deaths.
I think that is why my alarm bells started going off when I saw Huntsman's entry. :ahhh
I checked with my favorite mountaineering book, sure that it would confirm my perception that this is a dangerous knot to use; however, I was wrong!
From <u>Mountaineering, The Freedom of the Hills</u>: (They call it the "Double Overhand Knot" .)
The double overhand knot is useful as a rappel knot in icy conditions or for rappels where the knot might catch when the rappel rope is retrieved.
I was surprised by this!
What does Ashley say about the overhand?
[The single overhand] is very secure but very weak, reducing the strength of the rope in which it was tied by perhaps as much as fifty percent. It also jams is difficult to untie, often injuring the fiber. For these reasons it should be tied only in small material that is not to be employed again, and where there is a considerable margin of strength.
The overhand bend, also called Thumb Knot and Openhand Knot, ranks higher than the Sheet Bend in security but is among the weakest bends. It is used in joining the ends of rope yarns by which hams, bacon, and bananas are hung.
OK....I sense some controversy.....
Doing a little more looking around on line, I came across a climbing website that reviewed the "European Death Knot": In Defense of the European Death Knot
The European death knot is more correctly referred to as the offset overhand bend. Quite simply, it is an overhand knot tied using two lengths of cordage. It is used as a method to connect two ropes for use in rappelling.
There are a few reasons why the EDK is a sound choice. The main argument for the EDK is that it is low-profile and asymmetrical. What this means is that it is less likely to snag in cracks or over edges, and has a tendency to turn inward to present the flat side of the bend to the rock edge. This reduces the potential for stuck rappel ropes when compared to other alternatives.
Additionally, the EDK is easy to tie, easy to untie (under normal loads), and easy to inspect. This cannot be said with much conviction for the other variations. For use in multiple rappels, it offers a significant time saving factor.
Letโs talk about correct tying [of the EDK].
Here are the important points:
โข Leave sufficient tailโ30-50 cm is ideal
โข Dress and pre-tension the EDK
โข A backup can be tied in the form of a second overhand above the initial knot. This increases the knot profile, but Moyer states that it maintains asymmetry and makes the knot harder to capsize.
โข Donโt use the EDK for tying sling/webbing/cordelette anchors. Moyer suggests the Tape/Water Knot or the Double Fishermans.
โข CHECK YOUR KNOTS. Inspect your buddies. Complacency=bad juju.โSo, on balance, it would appear that Huntsman is right. It is a practical knot for some applications. Especially where the knot may need to slip over a ledge or edge. However, it is also a weak knot. One source I found stated the *reduction *in line strength was 65%! That is a serious weakening of a line. Ashley's advice to have a "considerable margin of strength" would seem to be very well founded.
I'll confess that I remain highly prejudiced against the double overhand bend. Maybe it was an instructor sergeant threatening us with death if we ever survived using it and he found out. Maybe it's just a general dislike of a knot that jams so easily. Maybe because I know stronger knots that, while they may be slower to tie, are more confidence inspiring.
The overhand knot is my least favorite knot. I can only think of one, maybe two, specific knots that incorporates the overhand knot where the overhand knot makes some sense. Otherwise, I avoid it.
Great knot entry, Huntsman! I really enjoyed learning more about this knot....and maybe I'll give it a little more slack (heheheh) now that I've researched it a bit.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better ๐
Register Login


