Knot in October GAW
-
They're already coloured in! :ahhh
-
Usually....yes....
-
Spoiler knot: Blake's Hitch.

Another friction hitch, but this time with a slightly different use. This hitch, with more than a nod to the Prusik, can be used to tension a line back on itself, but it is more typically used for climbing as a fall-arresting knot. This one is popular with some climbers and arborists because it is easy to slide along a line, but seizes up tightly.
Another virtue is that it is easy to learn and tie, although, there are a few details to get right.
Here I've got a carabineer on a tether (blue rope) to be clipped into my safety harness. And I'm going to tie onto a standing safety line (red rope).
The working end of the line gets wrapped around the safety line four (4) times. It then comes back down, over the standing end (first green arrow) and under the safety line (second green arrow).

Now the working end gets fed up through the bottom two (2) twists.


This then gets snugged down and dressed. While theoretically not needed, tradition (and caution) dictates putting a stopper knot in the tail. I used the ubiquitous figure 8 in this case.

Another use is when making a single rope ascent. Here I have one rope that is fed through a ring (but for an arborist, it would be a sturdy tree crotch.) and back down to my carabineer (and safety harness). The tail (working end) gets used to make a Blake's hitch back on the standing end.

As I climb up, I pull the slack out by drawing the standing end down and sliding my Blake's hitch up. I'm secure for the entire climb!
To come down, the Blake's is manually slid down the line as I descend. Sliding down quickly can create heat and melt the rope, so it is best to take slow, short drops.

-
You can use a comb to get those knots out, Fuzzy......give it a try.
Comb:

-
-
-
Found a sweet little video, by a guy with a tree in his office, on the Blake's hitch.

- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
-
my knot is the The Icicle Hitch Knot.
The Icicle Hitch Knot is almost identical to the knot described by Ashley to hoist a spar (ABOK # 1762, p 299) and to the Klemheist. The only difference is that the other knots are tied using a loop of rope.
Its a great way to hoist in one direction in the direction of the ends. The knot slides opposite of that direction.
Uses: The Icicle Hitch Knot is used when force is applied parallel to a post or pole in only one direction. In August of 2009, it was fully reviewed in Practical Sailor. They found it to be superior to other slide and grip knots including the Rolling Hitch.
Advantages: The Icicle Hitch Knot grips a smooth surface so well that it even works on a tapered surface such as a marlinespike – hence its name.
Pros and Cons: The Icicle Hitch Knot is relatively easy to tie and can be used over a bar or at the end of a pole.
Method. Wrap the rope around the pole four times moving away from the pole end. Leave a loop hanging and pass the end of the rope back over the pole alongside the standing end. Pass the loop behind both ends and hook it over the pole. Tighten the knot. The final load should be parallel to the pole.




-
Last pics. There are some options to finish this knot.



-
If you don't have access to the end of the pole you can thread the cord.




-
I wasn’t sure I was going to do a 5th knot, but seeing the addition of the Urban X, I think I will have to for an extra chance.
-
Aloha --
In pictures #3 & 4 of the first Icicle hitch post, it looks like you pass the working end over the standing end....is this right ?

-
The Icicle hitch is a cool knot!
It is one that I've tried to keep in the back of my mind, but don't practice enough to be sure I've tied it correctly.
Here's an animated version:
-
-
Entry 5 - Halyard Hitch
The Halyard Hitch Knot is used to secure a line to a shackle (or ring or clip). For the Halyard Knot to work, the diameter of the shackle and line should be about the same. If the shackle diameter is too large the Halyard Hitch Knot cannot be tightened sufficiently to provide a grip on the working end so it does not come undone.
Structure The Halyard Hitch Knot has the same structure as the Stevedore Stopper but is attached to a shackle. When completed the end exits adjacent to the shackle and is almost invisible. By contrast the end of Buntline Hitch exits away from the shackle.
The Halyard Hitch is a compact knot which improves aesthetics over some other options.
Halyard Hitch cannot be tied or untied under load. After being heavily loaded, it can be hard to untie.

1-6). Pass the working end through the shackle, and wrap the working end around the standing end twice.
7). Next, take the working end and pass it through the loop that you’ve just made next to the shackle.
8). Pull the working end tight.
Optional) trim any excess line from the end. (When trimmed short, this knot should never be used for critical loads). It’s also a good idea to heat-seal the end for added security and protection.Some variations of the Halyard Hitch, feed the working end down through the wraps so that it ends up parallel to the standing end. This is not considered as secure, but may be better if the shackle diameter is larger than the rope.

The left is the standard method of tying the Halyard knot. The right is the alternative. -
Very cool.

I'm a bit of Buntline hitch fan, but this looks like an improvement. It almost seems like a cross between a Buntline and an Anchor hitch.
Very nice!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login





