Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Backspring to tool reference guide?

Scheduled Pinned Locked Moved Swiss Army Knights Forum
4 Posts 1 Posters 745 Views
  1. Home
  2. Tool Talk
  3. Swiss Army Knights Forum
  4. Backspring to tool reference guide?
Backspring to tool reference guide?
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • tlcrawford Offline
    tlcrawford
    Posts: 6
    tlcrawford Offline
    tlcrawford
    wrote on last edited by
    Quote Reply

      Greetings SAK friends. I have begun modding a half dozen Vic knives and would like to build a 91mm knife to have the clean look of the 93mm backsprings. With that in mind, I would like to know if I could make my knife configuration using only full-length backsprings and leave off the Awl, Hook, and corkscrew or mid-pivot phillips. I want to have the following blades/tools on the knife:
      Large Blade
      Can Opener/(Large Flat Head/Wire Stripper)
      Scissors
      Pliers
      End Pivot Phillips

      Optional tools (not replacing any of the above)
      File
      Electrician's knife

      Also, is there a published reference guide which shows what tools/blades will work with which back springs?

      Thank you!

      1 Reply Last reply
      • kamakiri Offline
        kamakiri
        Posts: 3,215
        kamakiri Offline
        kamakiri
        wrote on last edited by kamakiri
        #1 Quote Reply

          Cool project. You’re gonna need a LOT of vintage tools from before they had backside tools for each layer.

          Pliers- no problem. None have backside tools.

          Inline Phillips (2nd) EDIT: no problem if you’re going to include either the magnifier or a Lite module to go on the opposite side.

          Opener layer- I think the easiest route is a Phillips/magnifier spring and make the seats match the year/style of openers, including milling down to match the thickness.

          Scissors- Pre- ‘91 have no hook.

          Main blade- I think if you flip sides, it should work on a scissor spring with a thin spacer.

          File can be added with a wood saw spring from either pre-‘85 knife or a Fieldmaster.

          Small blade can be paired with main blade on a phillips spring and spacers for both sides or mill the spring sides ~0.3mm as needed.

          An ‘86-‘87 Champ would be a good starting point. The ‘thin’ 2.5mm wide pliers are sleek/clean looking IMO. But any Champ up to ‘90 would work effectively the same.

          13D53FAF-9F0E-4F77-B41C-E54A62BF4480.jpeg

          1 Reply Last reply
          • kamakiri Offline
            kamakiri
            Posts: 3,215
            kamakiri Offline
            kamakiri
            wrote on last edited by
            #2 Quote Reply

              ...and you have to figure out what you want to do about the backside scale, since you don’t need the cutout area for the corkscrew.

              1 Reply Last reply
              • tlcrawford Offline
                tlcrawford
                Posts: 6
                tlcrawford Offline
                tlcrawford
                wrote on last edited by
                #3 Quote Reply

                  Thank you so much Kamakiri. You have laid out everything for me clearly. It is obvious that you know so much about these knives/tools and even more obvious that I need to learn a whole heck of a lot more!

                  I appreciate the photo as well. It is essentially what I am going for. I have found a scale maker in Germany (w3rktrieb) who will make scales for me without the cutout for the corkscrew. You have me thinking though. I might be better off to build out a 93mm knife and start with a Farmer X so I'll have one of the two back springs (from the saw) I'll need for adding pliers. I don't know how to get an inline Phillips yet but I'd basically have just about everything I want in that configuration. I've seen a couple that Bob Lessard has done which was my original inspiration for the knife. I'd basically need to buy a Farmer (I have a new low priductuon run Topo pattern Farmer X en route from a seller in Germany) to get the second saw spring. Then I'll reshape and add pliers from a 91mm. Any thoughts you have on which direction you'd take it if you were to build out this particuar configuration? 91mm or 93mm? I'll be using the same scale maker for either build.

                  Thank you again.

                  1 Reply Last reply

                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                  With your input, this post could be even better 💗

                  Register Login

                  1. Home
                  2. Tool Talk
                  3. Swiss Army Knights Forum
                  4. Backspring to tool reference guide?
                  Reply
                  • Reply as topic
                  Log in to reply
                  COMMUNITY LINKS
                  EDC-TV SAKWiki GearFeed SAKSelector
                  Operational Funds

                  Help us keep the Unworkable working!

                  Make A Donation
                  November Goal: $300.00
                  Due Date: Nov 30
                  Total Receipts: $0.00
                  Below Goal: $300.00
                  0% funded
                  • Login

                  • Don't have an account? Register

                  • Login or register to search.
                  • First post
                    Last post
                  0