Ozark Trail (Wal-Mart) Multiforce: First Impressions and Wave Comparison
-
So the cross cut file on the Victorinox are actually the best?
Might rethink the reviews I heard of the SwissTool X about the nail nicks being on the wrong side. Still not bitten as I'd like to try a used SwissTool first, but no one I know of around here has a Victorinox I could use for a while.Pending a review of the file, might be a tool I can feel less guilty about to make it semi-knifeless. Maybe shorten the knife to box cutter size, and maybe shorten the saw to a flat butter knife like the Flair had. May have to remove or cut the other blade to make it knifeless.
The Ozark looks to be a bit thicker. How does the weight compare. Am guessing there's a cheap nylon case?
-
I tried to grab one today at my local Walmart. The app said they had plenty in stock, yet when I got there, they were nowhere to be found
Guess I will wait a few weeks. -
@SirVicaLot said:
I tried to grab one today at my local Walmart. The app said they had plenty in stock, yet when I got there, they were nowhere to be found
Guess I will wait a few weeks.I had that same problem the first time I looked. A guy that worked there could not even find them. I went to another Walmart, and they had them in the area where they keep camping tools and supplies on a shelf below where everything was hanging. They were actually behind another boxed item and I had to look pretty hard to see the large orange and green box they are in. The following week I went back to the first Walmart I looked at, and they were also in the camping area, but sitting on the upper shelf ABOVE all of the hanging items where they normally put overstock. They made me work for it!
-
You can Google it to find out which Walmart close to you has them in stock and order it online for the exact same price. You will receive an email in about an hour letting you know when it's ready to go and pick it up.
-
Went to Walmart again today and they had one on display, so I could handle it. I was unable to open the tool layer with scissors, knife, etc. The tools were so cramped in there, I would have needed a pry bar to get them deployed.
Not sure if this is a design flaw or something that could be fixed with some oil. I also had the feeling that I could not reach the nail nicks very well.I decided not to get one. Which I could not have anyway. Apparently they only had the one on display, but none to sell.

-
After much searching I finally found them in my Walmart. They’re under the glass case, and there was even one in the raggedy, ill-sorted display case itself. I handled it, and liked it enough to buy one. I’m really impressed, it’s a far better tool than my wingman. Some of my tools were a tad tight, but I loosened the pivots with a pair of torx drivers and that was that.
I like that I can tighten or loosen the plier and tool pivots independently. I can fine tune the ease of deploying the blades, and that doesn’t make the plier handles too loose.
Yeah this is a good buy. It’s a WAY better buy than a $60 wingman

Charles.
-
@NetsNJ said:
There is no magnet, so retention depends on a ball bearing spring in the supplied Ph/Flathead double headed bit they give you. The driver accepts LM proprietary bits, but there would be no retention. Impressively, the tool comes with a handy bit-extender. This does have a magnet, but a weak one.You say the bit extension has a weak magnet. This isn’t actually the case. It’s a normal magnet, but it is at a greater depth, and only contacts double ended bits. So it’s actually not particularly useful for regular bits. However, Double ended bits are pretty common. There are a couple sources.
Double ended bits with ball retention:
Milwaukee 11-in-1 screwdriver. $10-13 from amazon or Home Depot. Home Depot version has a different bit than amazon version.
Klien tools 11-in-1 screwdriver. $15.
Klein Tools replacement bits. You can order some interesting replacement bits, like the 13231 schrader valve/flat head bit, the 32752 combo bit, the 32554 4mm/5mm metric Allen bit, and more. It gets a bit pricey ordering them one by one.
Best way 88400 (#1, #2, 3/16, 1/4) 88401 (T15, T20, SQ1, SQ2) and 88402 (#0, #3, 9/32, 1/8) replacement bits. These come two to a pack for $5.
**Double ended bits without ball retention (work with magnet in bit extension): **
Wiha 77780 replacement bit kit for tradesman ultra driver. At $16 this is the best bang for your buck, but they’ll only stay retained in the bit extender. This kit includes a larger set of metric Allen bits as well. (6mm is not available from Klein tools)
I ordered the best way 88400 to get a #2 Phillips with ball retention, as the tool comes stock with a #1. Then I ordered the wiha kit. That seemed the most economical way to get a large bit selection.
Charles.
-
Got the Wiha bit kit in today. It all fits perfectly in the driver extension except the 5mm/6mm bit. The 6mm bit doesn't fit all the way down in the handle and doesn't touch the magnet. Everything else locks in place via the magnet perfectly.
Posted this in the wrong thread originally. Sorry for the cross posting.
Anyhow, I like these bits, they're high quality and fit will. I wish there was a solution for the 6mm bit to fit correctly, but it's so close to quarter inch that I just don't think a 6mm is suitable for this extension. The down side, of course, is that I can use the 6mm but not the 5mm, as it falls out and is not retained. D'oh.
But every other bit fits and works perfectly.
Charles.
-
One other thing. On both of the multi forces I own, the cutters touch when new. It took some use before they loosened up and wore in against each other.
In the photo below you can see where the cutters are wearing in. This one is still new and still a little stiff as the cutters haven’t fully bedded in yet.
Charles.

-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login