Shop projects
-
(I also meant to say I like it a lot)
Getting the sizes of projects right is very hard,
something will look great in the workshop but when you place it in real life it looks huge :o -
Just finished a model I put away a while ago cause I got stressed over it, but it’s done and put along side all the others,,
JR

-
Nice!
-
Very cool JR

-
I purchased one of those models at Disney world a couple weeks ago. Total impulse buy as I liked Avatar. After some you tube videos I'm a bit intimidated by it.

-
Cool

You should have no prob, there just such fun
JR -
Don't really have a shop, but the misc. tools I clamp to an old garden table today tackled shell casings to make lanyard beads. I had no idea how thick the end of a bullet casing was...


-
I just set up a ship in my cellar with the tools I inherited from my father in law. It's slowly coming together. He was a big gadget freak and a big time Leatherman fan.
-
@Barry Rowland said:
I just set up a ship in my cellar with the tools I inherited from my father in law. It's slowly coming together. He was a big gadget freak and a big time Leatherman fan.The ship/shop typo gave me a laugh. Thanks! Unless you are setting up a ship in your cellar?
Tools with a history are always nice. I have most of my father's power tools.
-
I’m just working on one of my models on my homemade workshop bench/table so I can sit in my recliner,
JR
-
@MadPlumbarian said:
I’m just working on one of my models on my homemade workshop bench/table so I can sit in my recliner,
JRThat's the way to do it!! At the moment I'll settle with my foldable seat!! :D
-
@WWW said:
That's the way to do it!! At the moment I'll settle with my foldable seat!! :DI was looking for a lap table and they were a fortune, and to top it off very small, so I bought a nice piece of wood, cut it to fit perfect, then stained it, the came up with an idea after i worked on a model, the models I work on are all metal, and all the pieces come in a few flat pads (you got to cut them out and form them) and since the recliners a little pitched, I used the router and plunged four holes from the bottom, dropped in a magnet in each, then used hot glue to fill each one, and since the model pieces are very small I ran a piece of paracord around the bottom so if anything slides it catches, all for cheap rather then expensive, plus ever so comfortable sitting in the recliner! Just put the tools off to the side! Here’s a few pics,,
JR


-

You could attach a cushion to the underside for when you sit somewhere without armrests.
-
@MadPlumbarian said:
I was looking for a lap table and they were a fortune, and to top it off very small, so I bought a nice piece of wood, cut it to fit perfect, then stained it, the came up with an idea after i worked on a model, the models I work on are all metal, and all the pieces come in a few flat pads (you got to cut them out and form them) and since the recliners a little pitched, I used the router and plunged four holes from the bottom, dropped in a magnet in each, then used hot glue to fill each one, and since the model pieces are very small I ran a piece of paracord around the bottom so if anything slides it catches, all for cheap rather then expensive, plus ever so comfortable sitting in the recliner! Just put the tools off to the side! Here’s a few pics,,
JRNiice!! Using the magnets was a clever idea, it must feel great and really comfortable!!
-
After watching countless hours of putty knife restorations, I was ready to restore one myself. But after seeing the ridiculous shipping prices on eBay I decided that I would have to buy localy. It was settled, localy it was. But the putty knives I'd found were in no need of TLC. They were NOS (New Old Stock), and were a better buy than older beat up ones. In that moment I realised that I could make one myself!! But as usual it took me ages to gather the willingness to produce one. After watching a rehandling by YouTuber 357magdad, I knew that I could not waste more time. And so this journey began...
Reclaimed wood from a "cake stand" (no idea what they're called), parts were filled with bugs, used my Stanley nº4 to taper and clean up the sides. The tenon was cut with a chisel to fit a 15mm copper connector that was cut in half.

A better look at the tenon. A hole was drilled and a slot was cut with a hacksaw. The slot is then carved into the handle with a modified hacksaw blade.

An old saw blade is cut and shaped to form the blade of the putty knife. Later decided to add the taper you see marked with a sharpie marker.

Decided against the round shoulders and went for straight 90º. The tang was also filed a little more, enlarging the slot was more difficult than making the tang narrower.

Finished product with the copper "ferrule" in place. I reckon that I could use a reduction to get a little bit of a radius on the top of the ferrule.

Backside of the handle. I did not apply any finish as I may change my mind regarding the handle shape.

Sorry for the bad photos and the unnecessarily long windedness!
-
Nice project and well done !
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


