Gerber Clutch
-
About that stiff screwdriver blade...is the fingernail file blade (opposite it) difficult to open as well? Perhaps the pivot screws are too tight?
-
@J-sews said:
About that stiff screwdriver blade...is the fingernail file blade (opposite it) difficult to open as well? Perhaps the pivot screws are too tight?Thanks for the suggestion, J-sews.
Hard to tell for sure.
The fingernail file had a wider, deeper nail nick which allows a nail to gain better purchase over a bigger area.
It is also further out from the pivot, which means a longer lever arm about that pivot. Longer lever arm means less force must be applied to the nail nick to overcome spring tension and open the nail file.
If the pivot screws are too tight, I don't have a way to loosen them because they require a Torx driver smaller than the smallest one I have on hand.
.
-
I have handled a few of them and just about all of them seemed a little tight.
Def
-
Okay, I think I know what the problem is. But it is difficult to explain, and almost impossible to fix without disassembling your Clutch.
Check out the picture below. See that little bump on the back portion of the screwdriver blade? Every blade and driver on the Clutch and the Shortcut has a bump just like that. Now close the blade slowly, and follow the little bump along and watch what it does. See how at the very end of the stroke, as the blade becomes fully closed, how the little bump emerges from underneath the folded handle metal? The function of the little bump is to keep the blade tight in the closed position when not needed. Opening that blade means overcoming some resistance, wedging the little bump back underneath the handle metal.
If there was a way you could grind the bump down a little bit, I think it would solve the problem. (By the way, mine is tight, but not overly tight.)

-
It would be tight, but you may be able to grind that down a little with a Dremel tool without taking it apart....
Def
-
@J-sews said:
Okay, I think I know what the problem is. But it is difficult to explain, and almost impossible to fix without disassembling your Clutch....If there was a way you could grind the bump down a little bit, I think it would solve the problem. (By the way, mine is tight, but not overly tight.)Thanks, J-sews. You may well have diagnosed the problem correctly.
Right now, I plan on swapping this Clutch for another Clutch at Lowes.
I think this must be an unusual problem. This screwdriver isn't just a little tight, it's extremely hard to open without cracking little divots out of my thumbnail. Lubing it and exercising it hasn't made much of a difference.
I don't feel like I should have to spend more money to get the right Torx bit to open this Clutch up, then grind away on the screwdriver blade, then reassemble it and hope for the best.
.
-
I agree completely. Hopefully the replacement you get will not have the same afliction. :-\
-
@J-sews said:
I agree completely. Hopefully the replacement you get will not have the same afliction. :-\Update on my Gerber Clutch issue:
Rather than go through the hassle of returning the Clutch to Lowes, I resolved the screwdriver stiffness issue myself.
How? Simply by wearing it down.
While watching a movie on TV, I cycled the screwdriver from fully open to not quite closed then back to fully open. I did that over and over and over, one cycle every several seconds. Soon I was doing it without conscious thought, and I kept doing it throughout the movie.
By the end of the 2-hour movie, the screwdriver would open from its fully closed position much more easily. Slightly stiff, but no longer thumbnail-cracking stiff. After the movie was over, I re-lubed the pivot.
Screwdriver opening stiffness is now acceptable, and will probably continue to get better as it breaks in even more from regular use.
.
-
ringzero...That's how I broke in my Charge AL. My wife made me watch Ice Age 2 with her and the kids one night. I enjoyed the first one didn't like the second one so much. Had more fun playing with the Leatherman ;D
-
Good to see that worked out for you!
Def
-
@prime77 said:
My wife made me watch Ice Age 2 with her and the kids one night. I enjoyed the first one didn't like the second one so much. Had more fun playing with the Leatherman ;DMulti-tasking is the wave of the future. ;>
Why waste valuable time by just watching a movie or by just breaking in a new tool? You can easily accomplish both at once.
.
-
humour in Ice Age 1 I felt was effortless, very nice movie, the second was a disaster, forced jokes like in so many sequels (do not get me started on terminator 3).
-
Agreed. :(
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login