What did you use your Sak on today?
-
I'm staying in a vacation property (holiday home?) and as usual, the cutlery is terrible. Luckily the Spirit comes with a steak knife.

-
Used classic sd to make paracord sheath for classic sd
Used paracord and some thinner cord
Knife to cut and then seal the cord
Tweezers and toothpick to help thread it
Won’t let me upload pics at the moment for some reason -
@nolongerlurking27 said:
Used classic sd to make paracord sheath for classic sd
Used paracord and some thinner cord
Knife to cut and then seal the cord
Tweezers and toothpick to help thread it
Won’t let me upload pics at the moment for some reasonthe pic is too large for the server, check Swiss Army Knights for the chat on how to fix.
-
Well, I’m currently using the FarmerX because I’m attempting to make a pancake sheath with a fold over flap for it, the other piece of leather is currently soaking in the sink so I can stretch it over the FarmerX, so I took a pic,,
JR
-
Now the downtime, gotta let the leather dry out as it’s now formed,
JR
-
@MadPlumbarian said:
Now the downtime, gotta let the leather dry out as it’s now formed,
JRlooking good, almost ready...
-
Executive... only a few envelopes :(
-
Thanks, not even close! That leather is saturated and being clamped between two pieces of wood isn’t helping it dry any faster, yet I did put it over a air duct so every time the heat comes on it will warm it up a little, maybe by tomorrow afternoon it will be mostly dry? We’ll see,
JR -
@MadPlumbarian said:
Thanks, not even close! That leather is saturated and being clamped between two pieces of wood isn’t helping it dry any faster, yet I did put it over a air duct so every time the heat comes on it will warm it up a little, maybe by tomorrow afternoon it will be mostly dry? We’ll see,
JRyes! The house do the work till tomorrow!

-
Got to shopping in a bit but I was able to take the form apart to see how wet and how the leather formed overnight, got one little wrinkle at the bottom that I might be able to work out, other then that it’s about 80% dried out, if not more, so I think I should be able to work on it by the time we get home from shopping,
The other thing I did was took my sak out of the bag I had it wrapped up in so I could wear it, but I took the two pieces of leather and pressed them tight to the table so I could see how it would fit and it slid in smooooth! :D Screw the wrinkle, if I finally get a perfect fit sheath that I made that works who cares about a little wrinkle?
JR
-
Using it for what it wasn't designed for( again ) :D
Small flat driver turning square drive screws
-
Unfortunately I ended up cutting the one piece to short, so rather then waiting it I figured why not just make one without the flap? So that’s getting glued, but as of now I had to use the FarmerX again and put it back in the press for round #2 for making another front, already made another back with the flap, made it about another 3/4” longer too just in case,, so here’s the sak at work getting pressed with leather,, again..
JROh and the original where I cut the front too short where the flap wouldn’t reach, so it got cut to make just a simple pancake,,



-
Update,,
I finally got time, so I carefully lined everything up and checked it about three more times then cut it to fit,, and there it is.. I then roughed up the backside of each piece and lathered them up with glue, made sure everything’s good about three times and then put it in the press! So it will sit till tomorrow or the next day,
I also took the one I screwed up on and smoothed out the sides and cut the belt holes, so not that’s ready for the stitching..
JR

-
Strangely, I used my Farmer for a keyring. Look closely at the bottom of the sawmill control panel, and you will find that I now have a Farmer for a keyring for the sawmill.
.jpg)
-
And as I always says,
If you has a keys,
You needs alox to goes with it.
-
True words, Jim! I like your new sheath, MadPlumbarian - great work!

-
So today the Ranger's scissors got to do some "pinch-hitting."
I'm always fouling up the black plastic strapping when I strap the lumber stacks together. I use the scissors rather than a knife blade to clip the strapping when I want to reuse it. When hyperstressed, the strapping splits. I have to clip it back beyond the split and splice it with a clip. I find the scissors work better than a knife blade when you want a clean solid remnant that is strong enough to splice. The knife can exacerbate the split or start a new one, potentially. Scissors seem to make a more professional edge. (or maybe I just imagine it). ???
Oh, btw, 5 points to whomever can guess or figure out what kind of wood the strapping and Ranger are resting on.....

-
No real use of the Vic in general but I think it´s ok.
I am working in a mechanical workshop and everybody has gotten a Victorinox Alox Electrician.
Today my workmate wants to cut a pice of rope, but unfortunately it was a wire rope with fabric sheathing.
So it was time to give the blade a little sharpening service.
I took two pictures before and two pictures after sharpening the blade.Nice Weekend to all of you.





-
@Masel said:
No real use of the Vic in general but I think it´s ok.
I am working in a mechanical workshop and everybody has gotten a Victorinox Alox Electrician.
Today my workmate wants to cut a pice of rope, but unfortunately it was a wire rope with fabric sheathing.
So it was time to give the blade a little sharpening service.
I took two pictures before and two pictures after sharpening the blade.Nice Weekend to all of you.

Nice edge!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login