ZapWizard's Leatherman Free P4 Mods
-
Well, not quite everything
. The extender is monolithic, hence inherently more solid than the ratchet, whilst remaining thinner and thus potentially more usable in tight spots. Plus the extender and ratchet together provide more extension of reach if needed. Not quite redundant...
-
@Dutch_Tooler I am not sure there are enough customers who want to carry both for me to make that the default config.
@Syncop8r, I stay away from adding flashlight holsters as there are just way too many damn flashlights, no way to make a universal grip.
I do carry a seperate flashlight holster right next to my Free P4 holster, I just put them on together each time I head out to work. So this is why the separate holster is preferred myself.Before I go through the process of making it fit all the multitools, I may end up just prototyping the P4 version for myself to see if it replaces my holster as the daily carrier.
-
@ ZapWizard,
Understood. No real harm done as I usually carry the P4 holster together with a mini Skinth holding extra tools/bits which, lo and behold, has space for the ratchet (looks more in danger of falling out than it is, as the setting knob hooks behind the cover flap).
-
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
how are we not talking about this?
-
@Maxlvledc said:
how are we not talking about this?The first I have seen this. It's a bit funny that he made the video without watching the how-to videos I published. Fortunately he caught himself on that detail. (mostly)
His video does have some good points, I didn't realize how much folks would want the 4mm over the flat bits. -
I need some opinions on this.
I'd buy the ratchet holster variant. I'm even one of those horizontal carry weirdos.
-
@ZapWizard said:
The first I have seen this. It's a bit funny that he made the video without watching the how-to videos I published. Fortunately he caught himself on that detail. (mostly)
His video does have some good points, I didn't realize how much folks would want the 4mm over the flat bits.I'm with him, and I'm very thankful you were willing to make it. So thank you!
-

I finally got around to ordering the prototypes for the Ratchet Driver. Including a ratchet holder version of the P4 holster, not guarantees on that yet.
Also, for the past month I have been working on my own storefront, powered by Shopify.
Initially it will be stocked with just Shapeways sourced products, along with Amazon affiliate links for items which I can't stock.The main goal of the shop will be to reduce the confusion with all the variants and options available. The FREE P4 holster for example comes in more than 45 different configurations, and that doesn't even include the different color options.
Feel free to visit the site and sign up to be notified. (Link in the image)
-
That is great, Zap
I hope your new site does well as well as the sales

-
Have the ratchet driver holders came in yet? :ahhh
-
They were supposed to arrive today, but alas UPS Mail Innovations means UPS kicks your package around and then give it to the USPS to guarantee it suffers as much abuse and delay as possible.
-
:ahhh :ahhh :ahhhHoping it arrives in great condition at least by tomorrow

-
Well the parts arrived, but I am now very frustrated.

I ordered four prototype products for the Ratchet driver. Three of them have identical retention mechanisms.
The holster works beautifully, it snaps into place and isn't too loose or too tight. The micro carrier however required a whole ton of filing. (Nylon doesn't file well)
The 1/4" hex opening at the bottom on the holster is too loose, and the one on the micro carrier is perfect.Then there was the handle. Again the same retention geometry, but this time I had to file about 2x material away, and it still doesn't have the nice snap of the holster, just a dull press fit.
Finally, the deluxe handle. It had looser tolerances so that the bits could slide in and out, and relied on magnets. However, it is super tight and nothing slides without jamming up.SLS 3D printing typically holds a tolerance of +/- 0.2mm, but today it didn't. Some of the dimensions are off by 0.5mm. I think the issue is that Shapeways isn't fully cleaning out the internal powder before dying the parts, and the parts end up with the loose powder glued inside.
At this point I can tweak the tolerances and hope they aren't too loose, or just wait until I have access to a Fuse 1. Considering the production and shipping takes a month, I may end up with the Fuse 1 before I can receive another order.
-
Sorry to hear they didn't arrive exactly as expected
I am very hopeful that this will be a very awesome addition to EDC though
If you are planning on getting a 3D printer then it might be best just to wait
then you can perfect it at your leisure

-
ZapWizard.com is now open for business. I spend a lot of time on this website, making sure everything works great. Currently all the printed items are still fulfilled by Shapeways, but that may change in time.
I also finished the designs for the Ratchet drive accessories. I can now print up my prototypes on a Fuse 1, so that will save time on future developments. It's not my own Fuse 1, so I won't be able to do any production runs on it. -
Congrats on the website

Great about the 3D printer as well 8)

-
oh man, that mini ratchet handle/holder is fantastic
-
Looking forward to the horizontal holster with ratchet clip!
I'll wait until that's released as I'll be ordering a bunch of other bits and pieces and that Shapeways shipping to Oz is steep!
On another note, just thought I'd flag this YouTube video: https://youtu.be/ibw-GT-IRBA
Not sure if you're aware of this fellow or not and maybe there's some relationship there I'm not aware of, but if not it just seems a bit like he's misrepresenting your work as his. In the comments he's even discussing charging to make some modifications for another YouTuber.
-
-
@Michael
He also posted a follow-up video with my name since he wanted to live with the mods before promoting anything:
https://www.youtube.com/watch?v=0NCdzybkGvkSorry for the lack of new things (such as the ratchet added holster)/. I have been working on some other projects.
I have spent some time to get the ratchet design to work on all the tools so can update them all at once, but it is harder to fit to the Wave and others without it protruding. So soon that will get the P4 holster with ratchet driver ready to order for folks.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
