June Pocket Rocket Challenge
-
@ElevenBlade said:
Is Vic the way to go for a pull through sharpener, or are there other good options?The Spyderco Sharpmaker is a nice tool.


-
@ElevenBlade said:
Great info here. I'm currently planning on getting a sharpening system that would do well for Opinel knives, and of course Victorinox as well. Using a carbide pull through I was able to get a nice sharp edge, presumably because there's a full flat grind without a secondary bevel on the Opinel, but you know how rabbit holes can be. Since I was able to get a notable difference, I'm wondering if there are other options besides a) table top systems with clamps or b) a proper set of stones.Is Vic the way to go for a pull through sharpener, or are there other good options?
I've had great luck with the bottom ring of a coffee mug. A light touch up after breakfast to start the day. Some soup bowls work good too!
-
@Nix said:
The Spyderco Sharpmaker is a nice tool.

When you're as clumsy as me, would you be able to keep the angle steady? Do you just need to keep the blade perpendicular to the base? Is there an advantage to using this over a set of stones? (I'm guessing the answer is yes, and that it's actually easier to maintain a consistent angle) Can it get as sharp as 8000-10,000 grit stones? Am I asking too many questions?

-
@ElevenBlade said:
When you're as clumsy as me, would you be able to keep the angle steady? Do you just need to keep the blade perpendicular to the base? Is there an advantage to using this over a set of stones? (I'm guessing the answer is yes, and that it's actually easier to maintain a consistent angle) Can it get as sharp as 8000-10,000 grit stones? Am I asking too many questions?
You've got the idea: blade stays perpendicular to the base and the edge is stroked down the triangular "rods".
I think it is easier to keep a consistent angle with the Sharpmaker than with stones. (Unless, like me, you treat the rods like stones....)
The Sharpmaker comes with two sets of rods medium (grey) and fine (white). To start, use the corners of the grey rods (more aggressive), then the flats. The switch to white rods, corners first, then flats.
I can get a really nice edge using the white rods. Especially if I strop afterwards. Is it a 10K grit edge? I don't think so. I use a 12K stone to finish my straight razor for shaving. I am guessing that Murray Carter could use the white rods to get a shaving edge, but I don't think I could. I have a small pink ceramic stone that I picked up at a woodworking shop. That beauty is extra-fine and puts a super edge on a sharpened knife. I sometimes go from grey to white to pink.
I haven't settled on any one system. I have water stones, diamond plates, Arkansas stones, Sharpmaker, Edgepro, and some ceramic rods. They all work. Even a good coffee cup will work, but definitely strop the edge...on Carl's belt.

-
@ElevenBlade said:
Great info here. I'm currently planning on getting a sharpening system that would do well for Opinel knives, and of course Victorinox as well. Using a carbide pull through I was able to get a nice sharp edge, presumably because there's a full flat grind without a secondary bevel on the Opinel, but you know how rabbit holes can be. Since I was able to get a notable difference, I'm wondering if there are other options besides a) table top systems with clamps or b) a proper set of stones.Is Vic the way to go for a pull through sharpener, or are there other good options?
If you want to just use a pull through then I'd just get the Vic dual sharpener and make sure you keep on top of your edges, which is pretty easy to do since they made it as portable as a sharpie.
If you want a beginner/intermediate system then the rod systems are where you want to go. The angle is set by the rods, most systems give you at least two different angles to choose from and pack down self contained.
The Sharpmaker is great and was my last system (I regret selling it tbh, I should have kept it to keep my sharpening options more rounded), but if you're unsure what you want and don't want to drop a lot of money to test it then I recommend getting the Lansky Turnbox. It's the same principle as the Sharpmaker but less bells and whistles:
-Two set angles
-Coarse and fine ceramics
-Packs down into the small block of wood that actually makes it a system. It's literally 6 holes drilled into a block of wood.
As for the Sharpmaker, Spyderco does make higher grit rods that will fit it if you really want, they're not the cheapest of things though.
-
@Nix said:
You've got the idea: blade stays perpendicular to the base and the edge is stroked down the triangular "rods".I think it is easier to keep a consistent angle with the Sharpmaker than with stones. (Unless, like me, you treat the rods like stones....)
The Sharpmaker comes with two sets of rods medium (grey) and fine (white). To start, use the corners of the grey rods (more aggressive), then the flats. The switch to white rods, corners first, then flats.
I can get a really nice edge using the white rods. Especially if I strop afterwards. Is it a 10K grit edge? I don't think so. I use a 12K stone to finish my straight razor for shaving. I am guessing that Murray Carter could use the white rods to get a shaving edge, but I don't think I could. I have a small pink ceramic stone that I picked up at a woodworking shop. That beauty is extra-fine and puts a super edge on a sharpened knife. I sometimes go from grey to white to pink.
I haven't settled on any one system. I have water stones, diamond plates, Arkansas stones, Sharpmaker, Edgepro, and some ceramic rods. They all work. Even a good coffee cup will work, but definitely strop the edge...on Carl's belt.

Do... do you at least put the rods flat in the sharpmaker like they intend or do you Nix that approach too?

When are you going to go whole hog and get a Wicked Edge 3.0? We know you still have the storage space

I got my first real strop (well piece of leather dedicated to the purpose) recently with my whittling starter kit, but for the life of me not sure how to cleanly spread the green compund it came with, it's really hard at room temp, do I need to heat it up?

Hopefully it'll do better than a belt does

-
Great info everyone, thank you.
Maybe more in-depth than I'm ready for at this point though. :(
Seems I read somewhere that the pull-through on the Vic sharpener is angled specifically at 20 degrees, the standard angle for SAKs. (Which coincidentally is the angle from the thickness of the nub on the toothpick, according to NikGyver. So it can be used to get the correct angle when free-handing.)
For now I'll stick with the Vic sharpener and stay on top of blade maintenance. Should I pick up a used SAK in way bad shape, then I might try some of that in-depth info!
-
@SteveP said:
Great info everyone, thank you.Maybe more in-depth than I'm ready for at this point though. :(
Seems I read somewhere that the pull-through on the Vic sharpener is angled specifically at 20 degrees, the standard angle for SAKs. (Which coincidentally is the angle from the thickness of the nub on the toothpick, according to NikGyver. So it can be used to get the correct angle when free-handing.)
For now I'll stick with the Vic sharpener and stay on top of blade maintenance. Should I pick up a used SAK in way bad shape, then I might try some of that in-depth info!
Prevention is usually better than cure!
...until you fall deep enough you just want the sharpening stuff to have it. One of us. One of us.

-
@GearedForwards said:
Do... do you at least put the rods flat in the sharpmaker like they intend or do you Nix that approach too?
When are you going to go whole hog and get a Wicked Edge 3.0? We know you still have the storage space

I got my first real strop (well piece of leather dedicated to the purpose) recently with my whittling starter kit, but for the life of me not sure how to cleanly spread the green compund it came with, it's really hard at room temp, do I need to heat it up?

Hopefully it'll do better than a belt does


Uhhhh....I don't see how the base would support a flat rod. My Sharpmaker is really old. It is possible that newer versions have that option. I just jam a rod between my outstretched thumb and middle finger of my left hand. The knife to be sharpened goes in my right. Somehow it all works out.
The Wicked Edge looks very good, but not nearly as much fun as freehanding. And those mechanical sharpeners always take a bit of time to set up. It is so much easier to pull out a stone and touch up an edge. It is hard to argue against devices like the Wicked Edge, but I encourage people to become comfortable with freehand sharpening. It is easy to carry a small stone while you are out on a trip. Vic's are not known for great edge holding, but if you have a small stone it is easy to touch up an edge. Which is why I got the Vic sharpener in the first place.
I really like the Sharpmaker, but I can't recall when I last used the base......

With stropping compound, I have tried heating the compound first. I find it goes on too thickly.
Now I don't worry about getting an even coating of compound on the strop. I just rub the cold, hard compound over the surface in a couple directions. I rub it on without a lot of pressure, but I think the friction of rubbing it on still heats it enough to get it to stick to the strop.
As I strop the blade, the compound gets worked over the surface (to an extent). I think it is better to have too little compound on the strop rather than too much. I am a devoted stropping practitioner, but I'm sure there are some tips and tricks I could learn.
My thoughts on stropping as of this date:
• Top grain leather is better than the split side (balsa wood, thin cardboard, and thick paper can serve, too).
• A rigid strop (as compared to an old barber's belt strop) is best.
• Use a light amount of compound. If it builds up, remove it with steel wool or a scraper.
• Strop enough, but not too much. Over-stropping is a thing.
• Use a low angle to strop. A high angle can dull the edge, especially if you end up chasing an edge while over-stropping. If the low angle isn't doing the job, raise it slowly.....
• Green compound is great, the others (black and pink) are not needed (with possible exception of shaving razor)
• Slow and steady strokes seem to work best for me. Some gys like speedy stropping, but I haven't seen an advantage with that. -
Also: I love the Sharpmaker's rods for honing serrated blades. Simple scalloped serrations (Like Vic's or most kitchen knives) can be sharpened easily with the Sharpmaker's rods angled to use the corners.

-
Day 29
The Ambassador got a needed cleaning and sharpening after cutting tape, velcro with adhesive and aluminum foil.

-
Day 29, Very late post...
Today I took some notes using wife's Victorinox Signature

Enviado de meu moto g(6) usando o Tapatalk
-
Uhhhh....I don't see how the base would support a flat rod. My Sharpmaker is really old. It is possible that newer versions have that option. I just jam a rod between my outstretched thumb and middle finger of my left hand. The knife to be sharpened goes in my right. Somehow it all works out.
The Wicked Edge looks very good, but not nearly as much fun as freehanding. And those mechanical sharpeners always take a bit of time to set up. It is so much easier to pull out a stone and touch up an edge. It is hard to argue against devices like the Wicked Edge, but I encourage people to become comfortable with freehand sharpening. It is easy to carry a small stone while you are out on a trip. Vic's are not known for great edge holding, but if you have a small stone it is easy to touch up an edge. Which is why I got the Vic sharpener in the first place.
I really like the Sharpmaker, but I can't recall when I last used the base......

With stropping compound, I have tried heating the compound first. I find it goes on too thickly.
Now I don't worry about getting an even coating of compound on the strop. I just rub the cold, hard compound over the surface in a couple directions. I rub it on without a lot of pressure, but I think the friction of rubbing it on still heats it enough to get it to stick to the strop.
As I strop the blade, the compound gets worked over the surface (to an extent). I think it is better to have too little compound on the strop rather than too much. I am a devoted stropping practitioner, but I'm sure there are some tips and tricks I could learn.
My thoughts on stropping as of this date:
• Top grain leather is better than the split side (balsa wood, thin cardboard, and thick paper can serve, too).
• A rigid strop (as compared to an old barber's belt strop) is best.
• Use a light amount of compound. If it builds up, remove it with steel wool or a scraper.
• Strop enough, but not too much. Over-stropping is a thing.
• Use a low angle to strop. A high angle can dull the edge, especially if you end up chasing an edge while over-stropping. If the low angle isn't doing the job, raise it slowly.....
• Green compound is great, the others (black and pink) are not needed (with possible exception of shaving razor)
• Slow and steady strokes seem to work best for me. Some gys like speedy stropping, but I haven't seen an advantage with that.How old is... really old? I got mine something like 2013 I think?

You just turn the base over, the bottom accomdates the rods so you can use them as freehand stones:

I really like my Wicked Edge, I could do with higher grit stones, but I really want to upgrade to the 3.0 at some point, probably after an eventual move

I have only really stropped on the raw side of a belt or the heel of my hand (does okay actually).
Great tips though thanks! I looked at the DC4 combo stone recently, the leather pouch doubling as a strop was always a nice feature that appealed. Those sharpening cards (the one you carry in your wallet) are also nice but just too pricey over here to justify it since I don't really go anywhere to be away from my stuff anyway

-
@GearedForwards said:
How old is... really old? I got mine something like 2013 I think?
You just turn the base over, the bottom accomdates the rods so you can use them as freehand stones:
I think I got my Sharpmaker when the band R.E.M. was topping the charts and quiche was still popular. My base is just a chunk of plastic with holes in it. The underside is flat...sort of. Sal Glesser probably made it himself...in his garage...
I think it came with some brass rods that served as a guard....not sure where those went.

Still works, though. :D
-
@Nix said:
I think I got my Sharpmaker when the band R.E.M. was topping the charts and quiche was still popular. My base is just a chunk of plastic with holes in it. The underside is flat...sort of. Sal Glesser probably made it himself...in his garage...I think it came with some brass rods that served as a guard....not sure where those went.

Still works, though. :D
Does it work if you're not actually using it?

-
Day 29
Not much work for the Executive today, itching to get back to the full variety now I've gotten back into EDC channels.
Today's picture is a test of a set up I'd use to record YT videos, I've been wanting to start an EDC channel for a long time. What do you guys think of the lighting and backdrop?


-
I'm a complete novice at sharpening and I'm sure I sometimes do more harm than good, but when trying to put an edge back on a 20+ year old Work Champ, this worked perfectly;
Not perfect, but it's got me to a stage where I can use the Vic sharpener and another stone to keep working on it. I'm now trying to get in the habit of just doing a few passes with a stone/Vic sharpener once in a while to keep on top.
I know pull throughs aren't perfect, but that worked perfectly fine for me. One to consider.
I've also got a Sharpmaker which I haven't been bothered to use, yet...
-
Me too, and Mrs. R has an electric sharpener too

@Nix said:
Mrs Nix has...**** gasp ****...an electric pencil sharpener.Me, I prefer a hand-tuned pencil point. (My father always cut his pencils. I liked the way his handwriting looked, so I started doing it too. Although...I'm fond of a mechanical pencil as well.
) -
Day 30: This month absolutely flew by! For me, it really didn't take much of a change in my carry, as I always have a Classic on my keychain too. The big thing for me was that I intended to carry the mighty Minichamp or the Wenger PTC exclusively this month. I carried each, but not in the way I thought I would. I found that, for me, the Classic handled my day to day tasks very well, at a bit lighter weight and girth. As I'm finding as I go on, I used the blade more than anything else, followed by the scissors and tweezers. I was supposed to be doing a campout with my son and his Boy Scout troop at Mt. Washington, New Hampshire this month, which would have been a fabulous time for the Classic, but neither of us made it.
Just like Mrs. R and Carl have said, I can easily get along with a Classic or the heavy duty version, the Executive. I can see how General Yeager got along just fine with his in the mountains. The only place mine came up short (pardon the pun
), was in the kitchen. In this case, I usually have an Opinel of some sort in my pocket. This month might have just confirmed what I've suspected for some time: a Classic will do me just fine! I'm typing this on a desktop so a pic will follow later today.
Thanks to everyone for a really good time, and I hope everyone enjoyed this Challenge. Don't forget to put in for your badge, and congrats!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login