Gerber Mr. Pinchy Multi Plier Club
-
UPO 13 / 20
Break TimeWhen I saw it at first, I thought it must be a new discovery.
Oh yeah I got an unknown model with a cable cutter !But it is not a cable cutter.
Somebody processed the original pliers.Apparently the original pliers is the P-4 type.
If someone needs a tool like this, something like a nippers, it is easier to buy a nippers than to make it.
So I thik someone cut the broken pliers.If it is a prototype, I am very happy.
-
I agree with your suggestion that the tip was broken and then reshaped. This is the most plausible explanation.

-
Max Stone
Thank you for your reply.

It's fun to imagine a lot about Mr. Pinchy ! (´∇`)UPO 14 / 20
V2.0 with FileAs I mentioned <u>before</u>, the file have appeared instead of the utility blade since P-4 type pliers era.
So combination of P-2 pliers and the file is too early event. I am very surprised to find this one.The double lined font of GERBER, the thin grinded lanyard ring, the angled can opener craw and M-1 type patent marking are all early features, except the file.
Has anyone modified this?
Patent markings
Right to left: M-2, M-2L, M-1Oh I also talked about the size of patent markings <u>before</u>.
I think they made M-2L marking with same font as M-1 at first, then they changed it to a smaller font and made M-2 marking. -
UPO 15 / 20
Black Pre-production Utility BladeThis is black V2.0, early model with P-2 pliers.
If you look closely, you can see that the nail nick on the utility blade is not in the correct position.
I think this is pre-production utility blade.
Upper: pre-production utility blade
lower: normal utility bladeOne difference between them is the location of the nail nick. Another difference is the presence/absence of the "GERBER" mark.
I suspect that the pre-production utility blade had the same manufacturing process as a regular blade, until engraving "GERBER". -
Very nice to see the pre-production model

-
all
Thank you very much ! ( ˘ ³˘)
About the pre-production utility blade;
Until recently, I decided it was a prototype because I found only SS one.
But now I have a total of three. I introduced BO one in last post, I will mention another SS one after.
So it may not proper that I call them "pre-production". They may be just a "early model". (´~`)
I welcome new discoveries and new opinions!UPO 16 / 20
V2.0 Black One/Two Handle Cut-outs MixedThis is a V2.0 model.
As you see, the handle of serrated blade side has only one cut-out. The other handle has two cut-outs.
One cut-out handle was a feature of the early V1(mirror finish) models. So I am surprised the combination of P-2 pliers, one cut-out handle and black oxide finish.
The black color of the one cut-out handle seems pale. It may have something to do with its origin(mirror finish parts).By the way, this utility blade is a normal type. The nail nick is useless because it is behind the handle when folded.
...Oh, wait !
Is this the answer to why the nail nick of pre-production utility blade was placed inside ?
And the thick and grinded lanyard ring is also a feature of V1 models... C'mon !
-
I think you have the answer why the nail nick was on the inside. Good discovery!

It seems that Gerber was fine-tuning the design during early production and there were examples of parts being mixed up as design features changed.

-
I think you have the answer why the nail nick was on the inside. Good discovery!

It seems that Gerber was fine-tuning the design during early production and there were examples of parts being mixed up as design features changed.

-
Max Stone
Thank you very much !
It's fun to see the history of Gerber's improvements, but it is a hard work. ┐('~`;)┌
I'm glad if my opinion is correct.UPO 17 / 20
V1.2 with Thick LanyardThis is a V1.2 model. Both handles have two cut-outs. And the position of nail nicks are correct.
I introduced almost same model except the lanyard <u>before</u>.
Upper: V1.2 with thick lanyard (same as above)
Lower: V1.2 with thin lanyard (introduced before)The turning point of thick lanyard to thin, and one cut-out on handle to two were almost same timing.
So, these two models could be a judgement material when I decide which event was occurred at first.
Upper: V1.2 with thick lanyard
Lower: V1.2 with thin lanyardComparison of thickness.
-
Off topic but, why can't Fiskars bring back that scissors size, with the current spring design!?!? That would make the Pro Scout and Bladeless an even better tool!!! (or even incorporate it to the Basic model by replacing the current openers for the combo tool of the Suspension NXT!)

-
@Juan el Boricua said:
Off topic but, **why can't Fiskars bring back that scissors size, with the current spring design!?!? **That would make the Pro Scout and Bladeless an even better tool!!! (or even incorporate it to the Basic model by replacing the current openers for the combo tool of the Suspension NXT!)

Because these were terrible scissors - the later Fiskars scissors were much better. There's a reason Gerber stopped fitting them very early in their evolution of the Mr Pinchies.
-
Oooh, ok; thanks, Greg. I thought they might have been better.

-
@Juan el Boricua said:
Oooh, ok; thanks, Greg. I thought they might have been better.
I've never tried them myself but I remember it being said that these were the worst scissors "Fiskars" ever made. :D
-
@gregozedobe said:
To be fair I had an idea these might have been designed and made before Fiskars actually got control of Gerber MT production.I think I'm right in saying that they did start making them after Fiskars had bought Gerber. However I also suspect that the moment Fiskars realised what was going on they quickly put a stop to it. :D
-
I have try to cut klinex several times. But I couldn't ! (´Д`|||)
Totally useless... but I really love this shape. (´ε`*)
Now I am preparing next post to introduce UPO 18 / 20. But on the way, I made a new discovery. ('O'*)
So please wait next post just a little. -
Just want to say a huge thanks for all your work to this Hiraboo. And of course to all the others that add new informations and keep this thread going

@hiraboo said:
...
Now I am preparing next post to introduce UPO 18 / 20. But on the way,** I made a new discovery**. ('O'*)
So please wait next post just a little.
-
@McStitchy said:
Just want to say a huge thanks for all your work to this Hiraboo. And of course to all the others that add new informations and keep this thread going
100%
great work hiraboo. I look forward to see a group photo of all your Pinchys when you finish showing each in such good detail. 
-
@Max Stone said:
]
100%
great work hiraboo[/b]. I look forward to see a group photo of all your Pinchys when you finish showing each in such good detail. 
[quote author=McStitchy link=topic=74830.msg2267256#msg2267256 date=1627660546]
Just want to say** a huge thanks for all your work to this Hiraboo. And of course to all the others that add new informations and keep this thread going**

Thank you all for your research, knowledge, collections, web site management and most of all, your time; the wealth of information found in MT.o (also fun to go through and participate) is invaluable to appreciate "these crazy gadgets".
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login