Daredevil Challenge 2021
-

This Wetols I got from Amazon cost me $22, and considering the lower cost, it is actually relatively well made. But it is a real pant dragger(which I really do hate), and I sworn I need to hold onto my pants whenever I need to take a leak. Crazy heavy, a whopping 336g (11.8oz), it looks beefy right next to a Spirit X.
That's a good sized tool you have there Comis
(I'll just leave that one hanging...
) -
@Adam5 said:
I am marinating a couple of pork tenderloins this morning and decided to use a non-alcoholic Heiniken as the liquid. I pulled out the TripSaver to open the bottle and then remembered that for the TripSaver the can/bottle opener is replaced by an awl. No problem.I grabbed the bottle with my left hand by the neck. I stuck the plier head tips under the bottle cap and, using my left index finger as a fulcrum, pried the bottle cap off. A trick that I am sure many if not all of you know. I had no worries about the plier tips. The plier head is quite robustly built.

"Necessity is the mother of invention" Adam

-
@Alan K. said:
Day 01
The Gerber MP-600. I've never liked it because the tools are short for a full size tool and it is uncomfortable for me to carry it. Here the sliding pliers are seen withdrawn and deployed.I fully agree with this point of view (same issue for me with the OHT)
I have a work issued MP600 but was lucky enough to be part of a trial for the OG Surge & never looked back :D
Best of luck

-
@Humayd A R Mahomedy said:
:D
what can i say :DI'm in the same position as you mate (using a LM OHT)
The general consensus is that it's a jolly, damned fine, splendid tool
Fact is, it's NEVER worked well for me. I hope to be won over

Best of British to you

-
@comis said:
So as long the mods does not alter the original too much, I think it is acceptable. But I would suggest to refrain from doing further mods to the tool until the end of the challenge.
Fair enough, comis.
The length of the list of potential mods at the end of 30 days will be a good indication of my acceptance of the S557. ;)
-
<u>Day 1</u>
So my first offering for the Daredevil challenge is, quite frankly, not very daring ::)
However, for me it's a rare useage shot
Changing the bulb in the O/S light (the OHT helped ;) )
-
So my first offering for the Daredevil challenge is, quite frankly, not very daring ::)
However, for me it's a rare useage shot
Changing the bulb in the O/S light (the OHT helped ;) )Just barely long enough to get in there and too short for complete rotation. Will an extension driver fit the OHT?
-
Great start out of the gate :ahhh

-
@SurgeUk said:
I'm in the same position as you mate (using a LM OHT)
The general consensus is that it's a jolly, damned fine, splendid tool
Fact is, it's NEVER worked well for me. I hope to be won over

Best of British to you

why thank you kind Sir.
i also have an OHT,but it's not very practical for me.
i might run it if there ever is an OHT challenge :D -
Day 1 of 30
Well, I have never been a fan of the Gerber Suspension ::) so when the NXT came out it looked better so I bought one of them :D It has a combo blade and I also dislike those
I am glad this started on a Sunday so I can get use to it a bit more before an actual work day :ahhh I do really like the clip on it anyways 
Let the month of hopefully not misery begin



-
Some great and perhaps understandable choices here. The OHT just looks too bulky. I'd rather stick with the Rebar, which is tiny. The Suspension NXT had me interested when it came out, along with the Truss. I still think about getting one or the other, or both. I still might. They do seem fine. We'll see.
-
@Alan K. said:
Just barely long enough to get in there and too short for complete rotation. Will an extension driver fit the OHT?I don't have an official LM extension driver, yet (just a generic one that came with my other potential candidate)
That one however, does fit over the awl (just) but is a bit rattly ::)
I'll try to continue without resorting to other attachments and just go "commando" where possible

-
@ReamerPunch said:
Some great and perhaps understandable choices here. The OHT just looks too bulky. I'd rather stick with the Rebar, which is tiny. The Suspension NXT had me interested when it came out, along with the Truss. I still think about getting one or the other, or both. I still might. They do seem fine. We'll see.The OHT is VERY bulky and as I don't use my Rebar a great deal maybe I should have chosen that

I don't think I could bring myself to buy a "Truss" (non medical usage aside :ahhh )
-
Yes, yes... much better photo with a Suspension NXT than with a Rebar or Mini Tool. You will not regret taking part of this challenge Poncho!

-
Day 1 - And so it begins...
An easy start for the S557 on a lazy Sunday afternoon.
All it had to do was cut open the foil cap on a bottle of windshield washer fluid, as seen here in this dramatic recreation after I got my phone.

-
@Sos24 said:
I was thinking about backing out of this challenge due to there being too many awesome tools and too little time to spend a month using something I don’t like.But then I decide to stick with it. I had three candidates -
- Victorinox Evo S18 - As much as I love SAKs of all sizes, I can’t stand the ergonomic grips on the Evo line. I also find the locking mechanism uncomfortable and awkward.
- Leatherman Squirt PS4 - I really wanted to like this little tool and would if I didn’t find the two drivers nearly impossible to open. The nail nicks seem to be so shallow, small and close to the scales that I find they do not work.
- Kutmaster Minimaster - I do not like having to open it to access any tool. I also do not like that with just about any tool you try to open, all the tools want to come open. Also, I’m not sure why but I just feel the quality may be a little suspect, which irritates me due to how much I like my old Utica knives.
After some deliberation, I’ve decided on the Minimaster. I feel that maybe I haven’t given the Minimaster a fair chance compared to other tools by bigger names.

I am glad you decided to stay in this.

I have one of those tiny tools. The scissors were very loose on mine, so I gently bashed the pivot with a hammer, to get the scissors to be able to cut. But the tool is still below average. The two handles have no retention when closed. And when you open a tool, and close the handles, the tool is supposed to be somewhat locked. Nope. Not on mine. The implements can move about 45°. Pretty bad. I keep it in a sewing kit. -
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
