Daredevil Challenge 2021
-
Day 3
I found something that the TripSaver does relatively well (relative to other MTs). I drove a ground rod (also known as a earth rod) and needed to connect the ground wire to the rod with a direct burial ground clamp. To install the clamp, you slide it over the wire and rod and tighten the bolt. My Knipex were back at my van, so I used the TripSaver instead. The plier head can handle larger bolt heads than the typical MT. The only aggravation is that the handles really do close too closely together. I can not work the MT one-handed nearly as well as I can other pliers and MTs.

-
@SteveP said:
Day 3 - First Grumbles...The serrated, Wenger-design scissors do not cut flimsy stuff well at all.
I tried to cut up the plastic rings that held my bottles of Diet Coke and the S557 wasn't doing it. The plastic just wrapped around the scissors blades. If I cut with just the tips of the scissors, held the plastic taught, and cut with a sharp snap, then it worked.
Same with opening my bag of chips for lunch.
For comparison, I tried the non-serrated Victorinox scissors on my 1983 Champion. No problem cutting either item with them. Same success with regular kitchen scissors.
I bought the S557 new in May and it's seen very litle use since then, so I don't think I'm dealing with dull scissors.
I have a Evogrip 14 and I was disappointed with its scissors. It has trouble cutting pliable material.
-
Day 3
I was at Lowe's today. I went in there for a bifold door hardware kit, a new pair of linesman's pliers, and a new electrical outlet to replace one that tended to not hold plugs tightly anymore. WHile in the electrical stuff, I bought a new electrical meter. Battery had to be installed, but was included. Haven't heard of a 23A before. It's about 2/3 the size of a AAA, but about the same diameter. And, 12 volts! I normally go with analog meters, and I decided to try a digital one, despite being $10 more (while I can't do continuity as easy with one of these, it is easier to read). Because of the smaller size, it doesn't use a 9V like most of my other meters.

Part of the reason I rarely ever carry this Swiza is that the backside Phillips is smaller than that on a Victorinox (or even Wenger/Delemont). However, a lot of battery covers are #1. I have usually been carrying my Bond as my main pliers-based tool, and if I need a bit that is Torx or hex (most of what's in the kit as I have the removable adapter card laid out), I use the removable bit adapter. I don't keep the #1/#2 bit in the card anymore; as I had to make room for a more speciality bit from the larger bit kit. That helps make it a good multitool companion.

-
Great uses Adam and cody

-
@Adam5 said:
I have a Evogrip 14 and I was disappointed with its scissors. It has trouble cutting pliable material.Thanks, Adam. I'm glad I'm not the only one.
Later in the afternoon, the Wenger scissors failed cutting through a piece of very thin elastic cord and through a plastic bag. I couldn't even slice along the length of the plastic bag because of the serrations.
So scissors that don't cut - fail!
-
Getting my kit ready for work tomorrow and I'm sneaking in the OHT (so I can use it more)

I tried to fit it in the pouch I use for my OG Surge (it was, to say the least, snug ) :P
A change of clothes was required so I used this old LM pouch (no idea what was originally in it
)
-
-
I was at Lowe's today. I went in there for a bifold door hardware kit, a new pair of linesman's pliers, and a new electrical outlet to replace one that tended to not hold plugs tightly anymore. WHile in the electrical stuff, I bought a new electrical meter. Battery had to be installed, but was included. Haven't heard of a 23A before. It's about 2/3 the size of a AAA, but about the same diameter. And, 12 volts! I normally go with analog meters, and I decided to try a digital one, despite being $10 more (while I can't do continuity as easy with one of these, it is easier to read). Because of the smaller size, it doesn't use a 9V like most of my other meters.

Part of the reason I rarely ever carry this Swiza is that the backside Phillips is smaller than that on a Victorinox (or even Wenger/Delemont). However, a lot of battery covers are #1. I have usually been carrying my Bond as my main pliers-based tool, and if I need a bit that is Torx or hex (most of what's in the kit as I have the removable adapter card laid out), I use the removable bit adapter. I don't keep the #1/#2 bit in the card anymore; as I had to make room for a more speciality bit from the larger bit kit. That helps make it a good multitool companion.


What brand of linesman pliers did you get? -
@Fireman said:
I missed his pic the first time through the thread, and I'm not sure I should thank you for pointing it out.
Your question, though, is THE question of the day. Is there a place that actually sells a piece of toast, an egg, what appears to be Vienna sausage, and a piece of...something else? Is the KFC cup a clue? Is this from the Gas Station MRE challenge?Meal 3C? I just walked right into KFC, and that's what on the menu.
Btw, that piece of UFO is chicken! (If you watch enough survival show like me, you will know anything you can't put a name on it is chicken :D )Btw, I'm looking forward to the Holiday Edition of GSMRE.
Getting my kit ready for work tomorrow and I'm sneaking in the OHT (so I can use it more)

I tried to fit it in the pouch I use for my OG Surge (it was, to say the least, snug ) :P
A change of clothes was required so I used this old LM pouch (no idea what was originally in it
)Looks like it's ready for work!

@SteveP said:
I would have been really impressed if you'd used the hammer claw to open the package.

It's Hammer Time!
:D
-
@Alan K. said:
Great job on the magnetic tool holders Comis. I like the wrap around sheath using heat shrink tubing. That's something I never would have thought of.
Glad you like it!

@Alan K. said:
Day 03
Afternoon smoke interrupted by the afternoon rain which started early today. So here's the MP600 Pro-Scout on my umbrella.This picture reminds me of a LM tool that I constantly find rusty no matter what I do with it. I could have sworn I even drench it with WD40 and it will still rust in a few months time sitting in a dry cabinet. Eventually I have accepted the fact that some tool will just rust if you look at it wrong.

@SteveP said:
Day 3 - First Grumbles...The serrated, Wenger-design scissors do not cut flimsy stuff well at all.
I tried to cut up the plastic rings that held my bottles of Diet Coke and the S557 wasn't doing it. The plastic just wrapped around the scissors blades. If I cut with just the tips of the scissors, held the plastic taught, and cut with a sharp snap, then it worked.
Same with opening my bag of chips for lunch.
For comparison, I tried the non-serrated Victorinox scissors on my 1983 Champion. No problem cutting either item with them. Same success with regular kitchen scissors.
I bought the S557 new in May and it's seen very litle use since then, so I don't think I'm dealing with dull scissors.
Vic scissors is the best, especially for precision cut. I think Wenger's 'shear' is meant for more robust stuff, but it's not too shabby if the medium is just paper. One way I used to test a scissors is to have it cut cling wrap, if it could cut it with ease, it's a good one.
I found something that the TripSaver does relatively well (relative to other MTs). I drove a ground rod (also known as a earth rod) and needed to connect the ground wire to the rod with a direct burial ground clamp. To install the clamp, you slide it over the wire and rod and tighten the bolt. My Knipex were back at my van, so I used the TripSaver instead. The plier head can handle larger bolt heads than the typical MT. The only aggravation is that the handles really do close too closely together. I can not work the MT one-handed nearly as well as I can other pliers and MTs.

Good use!

-
I was at Lowe's today. I went in there for a bifold door hardware kit, a new pair of linesman's pliers, and a new electrical outlet to replace one that tended to not hold plugs tightly anymore. WHile in the electrical stuff, I bought a new electrical meter. Battery had to be installed, but was included. Haven't heard of a 23A before. It's about 2/3 the size of a AAA, but about the same diameter. And, 12 volts! I normally go with analog meters, and I decided to try a digital one, despite being $10 more (while I can't do continuity as easy with one of these, it is easier to read). Because of the smaller size, it doesn't use a 9V like most of my other meters.

Part of the reason I rarely ever carry this Swiza is that the backside Phillips is smaller than that on a Victorinox (or even Wenger/Delemont). However, a lot of battery covers are #1. I have usually been carrying my Bond as my main pliers-based tool, and if I need a bit that is Torx or hex (most of what's in the kit as I have the removable adapter card laid out), I use the removable bit adapter. I don't keep the #1/#2 bit in the card anymore; as I had to make room for a more speciality bit from the larger bit kit. That helps make it a good multitool companion.

23A is kinda common for wireless door chime, but I agree, it was an oddity when I first saw it. I haven't used my Swiza for the longest time, but did vaguely remember the tolerance of the tools kind resembled Wenger/Delemont. How was your copy?
@Adam5 said:
You will deserve whatever badges you receive after using that thing for 30 days Echo

-
@SteveP said:
Thanks, Adam. I'm glad I'm not the only one.Later in the afternoon, the Wenger scissors failed cutting through a piece of very thin elastic cord and through a plastic bag. I couldn't even slice along the length of the plastic bag because of the serrations.
So scissors that don't cut - fail!
The S557 very slightly redeemed itself at dinner by successfully opening a beer bottle.
But 4 scissor uses and 4 failures.

-
@Adam5 said:
Yes, the NXT's Phillips driver is much better than the Suspension's 2D Phillips.As for SAKs, I won't carry one without an inline Phillips. Just too handy.
And my hex bit coupler fits on it well too.
(Some older Wengers had official 2D Phillips blades. I've never used one, but seems no more than a glorified nail cleaner.)
-
-
Day 4
If I'm gonna be stuck with the Flik for a month, I might as well try and improve it.
The Flik's bottle opener has a little bit of a belly. I decided to grind it straight with a Dremel. Maybe a minute's work.
Now, with both flatheads opened, they can accommodate the square hole bit adapter. It fits very well on there. No complaints. Now I can extend the reach, use standard bits, and it is much stronger than the dedicated Phillips the Flik has. Quite pleased with this. Now the Flik will have to commandeer the Rebar's sheath and bit set.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
I tightened a loose clip on a Dealt battery drill and it performed well :D




