Daredevil Challenge 2021
-
@Alan K. said:
Great job on the magnetic tool holders Comis. I like the wrap around sheath using heat shrink tubing. That's something I never would have thought of.
Glad you like it!

@Alan K. said:
Day 03
Afternoon smoke interrupted by the afternoon rain which started early today. So here's the MP600 Pro-Scout on my umbrella.This picture reminds me of a LM tool that I constantly find rusty no matter what I do with it. I could have sworn I even drench it with WD40 and it will still rust in a few months time sitting in a dry cabinet. Eventually I have accepted the fact that some tool will just rust if you look at it wrong.

@SteveP said:
Day 3 - First Grumbles...The serrated, Wenger-design scissors do not cut flimsy stuff well at all.
I tried to cut up the plastic rings that held my bottles of Diet Coke and the S557 wasn't doing it. The plastic just wrapped around the scissors blades. If I cut with just the tips of the scissors, held the plastic taught, and cut with a sharp snap, then it worked.
Same with opening my bag of chips for lunch.
For comparison, I tried the non-serrated Victorinox scissors on my 1983 Champion. No problem cutting either item with them. Same success with regular kitchen scissors.
I bought the S557 new in May and it's seen very litle use since then, so I don't think I'm dealing with dull scissors.
Vic scissors is the best, especially for precision cut. I think Wenger's 'shear' is meant for more robust stuff, but it's not too shabby if the medium is just paper. One way I used to test a scissors is to have it cut cling wrap, if it could cut it with ease, it's a good one.
I found something that the TripSaver does relatively well (relative to other MTs). I drove a ground rod (also known as a earth rod) and needed to connect the ground wire to the rod with a direct burial ground clamp. To install the clamp, you slide it over the wire and rod and tighten the bolt. My Knipex were back at my van, so I used the TripSaver instead. The plier head can handle larger bolt heads than the typical MT. The only aggravation is that the handles really do close too closely together. I can not work the MT one-handed nearly as well as I can other pliers and MTs.

Good use!

-
I was at Lowe's today. I went in there for a bifold door hardware kit, a new pair of linesman's pliers, and a new electrical outlet to replace one that tended to not hold plugs tightly anymore. WHile in the electrical stuff, I bought a new electrical meter. Battery had to be installed, but was included. Haven't heard of a 23A before. It's about 2/3 the size of a AAA, but about the same diameter. And, 12 volts! I normally go with analog meters, and I decided to try a digital one, despite being $10 more (while I can't do continuity as easy with one of these, it is easier to read). Because of the smaller size, it doesn't use a 9V like most of my other meters.

Part of the reason I rarely ever carry this Swiza is that the backside Phillips is smaller than that on a Victorinox (or even Wenger/Delemont). However, a lot of battery covers are #1. I have usually been carrying my Bond as my main pliers-based tool, and if I need a bit that is Torx or hex (most of what's in the kit as I have the removable adapter card laid out), I use the removable bit adapter. I don't keep the #1/#2 bit in the card anymore; as I had to make room for a more speciality bit from the larger bit kit. That helps make it a good multitool companion.

23A is kinda common for wireless door chime, but I agree, it was an oddity when I first saw it. I haven't used my Swiza for the longest time, but did vaguely remember the tolerance of the tools kind resembled Wenger/Delemont. How was your copy?
@Adam5 said:
You will deserve whatever badges you receive after using that thing for 30 days Echo

-
@SteveP said:
Thanks, Adam. I'm glad I'm not the only one.Later in the afternoon, the Wenger scissors failed cutting through a piece of very thin elastic cord and through a plastic bag. I couldn't even slice along the length of the plastic bag because of the serrations.
So scissors that don't cut - fail!
The S557 very slightly redeemed itself at dinner by successfully opening a beer bottle.
But 4 scissor uses and 4 failures.

-
@Adam5 said:
Yes, the NXT's Phillips driver is much better than the Suspension's 2D Phillips.As for SAKs, I won't carry one without an inline Phillips. Just too handy.
And my hex bit coupler fits on it well too.
(Some older Wengers had official 2D Phillips blades. I've never used one, but seems no more than a glorified nail cleaner.)
-
-
Day 4
If I'm gonna be stuck with the Flik for a month, I might as well try and improve it.
The Flik's bottle opener has a little bit of a belly. I decided to grind it straight with a Dremel. Maybe a minute's work.
Now, with both flatheads opened, they can accommodate the square hole bit adapter. It fits very well on there. No complaints. Now I can extend the reach, use standard bits, and it is much stronger than the dedicated Phillips the Flik has. Quite pleased with this. Now the Flik will have to commandeer the Rebar's sheath and bit set.

-
@SurgeUk said:
It is a rather "unique" tool but, that said, different is good
It was given to me by a mate knowing I like MT's Surge, very kind but
so had just got chucked in a box.
This challenge seemed like the perfect time to give it a go. I really like the hammer as it goes, yes exactly, something a bit different....but as comis said in an earlier post, also a bit of a heavy tool to base an MT around and still make carryable
@SteveP said:
I would have been really impressed if you'd used the hammer claw to open the package.

It's Hammer Time!
watch this space...maybe

@Adam5 said:
You will deserve whatever badges you receive after using that thing for 30 days Echo
Thanks Adam
...to think what lovely tools i could be using
:ahhh ah well that's what challenges are for -
@comis said:
Vic scissors is the best, especially for precision cut. I think Wenger's 'shear' is meant for more robust stuff, but it's not too shabby if the medium is just paper. One way I used to test a scissors is to have it cut cling wrap, if it could cut it with ease, it's a good one.I just did the Official Comis Cling Wrap Test and here are the results:
- Vic scissors: No problem cutting or slicing through the cling wrap.
- Serrated Wenger-design scissors: Could cut the wrap only if using the ends of the scissor blades. Slicing motion failed.
So that makes 5 scissor fails in one day.


-
@ReamerPunch said:
Day 4If I'm gonna be stuck with the Flik for a month, I might as well try and improve it.
The Flik's bottle opener has a little bit of a belly. I decided to grind it straight with a Dremel. Maybe a minute's work.
Now, with both flatheads opened, they can accommodate the square hole bit adapter. It fits very well on there. No complaints. Now I can extend the reach, use standard bits, and it is much stronger than the dedicated Phillips the Flik has. Quite pleased with this. Now the Flik will have to commandeer the Rebar's sheath and bit set.

That looks like the exact same bit set and hex bit coupler I got with a Winchester multi tool and that fits very nicely on the inline Phillips of SAKs.
If anyone wants one, I found the bit sets with coupler for less than $3 on AliExpress.com.
-
@comis said:
Oh, wait, I think my magnetic sheath may work, if it doesn't imprint too much...(pls don't click if you are not ready to see grown man belly dance)
:D- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
You are so good at creating nice usable things.
-
Day 3
20210803_191233 by Humayd a r Mahomedy, on Flickr
glamor shot,no real use today :-[ -
Day 3
The Minimaster helped liberate a treat and toy for Fisher. I should have known better than to walk from the mailbox to grocery store, it takes me past the pet store.It also helped cut out some cooking directions on frozen food boxes, so I could throw out the boxes and create more room in freezer.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login





