Daredevil Challenge 2021
-
@ReamerPunch said:
Day 4If I'm gonna be stuck with the Flik for a month, I might as well try and improve it.
The Flik's bottle opener has a little bit of a belly. I decided to grind it straight with a Dremel. Maybe a minute's work.
Now, with both flatheads opened, they can accommodate the square hole bit adapter. It fits very well on there. No complaints. Now I can extend the reach, use standard bits, and it is much stronger than the dedicated Phillips the Flik has. Quite pleased with this. Now the Flik will have to commandeer the Rebar's sheath and bit set.


-
@ReamerPunch said:
I was waiting for this use!

Brilliant

-
<u>DAY 4</u>
The OHT was spirited into work on the QT where it assisted with deniable ops (repairing a battery pack)


-
Day 4
IMG-20210804-WA0017 by Humayd a r Mahomedy, on Flickra friend asked me to help him out with his RCBS Uniflow powder measure.
it was in storage and seized due to corrosion.
the large driver/pry was perfect for the slot head screws -
@Humayd A R Mahomedy said:
Day 4
IMG-20210804-WA0017 by Humayd a r Mahomedy, on Flickra friend asked me to help him out with his RCBS Uniflow powder measure.
it was in storage and seized due to corrosion.
the large driver/pry was perfect for the slot head screwsExcellent use there

-
Lots of excellent Day 4 content


-
Day 4 of 30
Scissors :ahhh Well they cut but when using them for more than a couple of cuts or in something a bit thicker than regular paper they aren't the most comfortable :ahhh but they do cut
:D

The unlock tabs still suck though

-

Mine doesn't have a saw or a file (well not a good one anyways
) 
-
-
-
Day 04
I used the partially serrated knife blade to open a bag of Cypress mulch. Knife blade is not very sharp so it ripped the bag open more than sliced it. I will have to give it a touchup. -
The OHT was spirited into work on the QT where it assisted with deniable ops (repairing a battery pack)

@Humayd A R Mahomedy said:
Day 4
IMG-20210804-WA0017 by Humayd a r Mahomedy, on Flickra friend asked me to help him out with his RCBS Uniflow powder measure.
it was in storage and seized due to corrosion.
the large driver/pry was perfect for the slot head screwsGood uses!

@Alan K. said:
Day 04
I used the partially serrated knife blade to open a bag of Cypress mulch. Knife blade is not very sharp so it ripped the bag open more than sliced it. I will have to give it a touchup.Do you think it has more to do with the serration than being dull? I recently watched a youtube vid from Felix testing serration vs non-serrated Vic blade, turns out they perform quite evenly(much to my surprise). But still, plain edge is that much easier to maintian.
-
**Day 4
**
The S557 did a better job with lunch today.The scissors cut through a grape vine fine, so they seem to be OK with firmer things.
And the knife blade had no problem slicing a tomato.

-
-
Created a hook on the end of a steel wire to help grab a wire in the ceiling that was out of my reach:

-
@Adam5 said:
Created a hook on the end of a steel wire to help grab a wire in the ceiling that was out of my reach:
That's one of my cases for the Multimaster family. I think that outside of real pliers, they have the toughest ones in the business. Even a bit more than the older SOG Toolclips, but their high value, even in POS condition puts the latter out of reach for most; when it seems Multimasters used are a hard sale. Like I said before, I paid $20 for three! Multimasters together (along with a Chinese clone Utica sold in their advertising merchandise business) and almost $60 for a well-used and abused Toolclip. And $30 for the Micro, which replaced one I paid about the same for and lost.
-
Scissors :ahhh Well they cut but when using them for more than a couple of cuts or in something a bit thicker than regular paper they aren't the most comfortable :ahhh but they do cut
:D

The unlock tabs still suck though

That handle looks a bit short to me. The scissors on a tool are the make or break for the most part. It seems that with multitool producers, the saw, file, and scissors are the most common to get wrong.
-
The scissors in Gerber tools are Fiskars scissors. They may be small but they will cut.
-
Day 5

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

