Half Multiforce
-
-
@Adam5 said:
I probably would not have made this one into a knife if I did not have a second one
This thread is gateway modding. See a very nice mod, buy a tool to make a copy. Realize you like the new tool. Buy a second one for the actual mod. Realize you need a spare because you like the original and the mod. Buy a third tool.

-
Not just a gateway because I have been modding for years and still will probably fall for the trap


-
Here is a short explanation of how I used the ferric chloride to produce the black oxide finish:
I prepared separate plastic containers with the following items:
Clean water (distilled is best)
Water mixed with dishwashing liquid
1 part ferric chloride and 2 parts white vinegar (this is the etching bath)
Water mixed with baking soda (to neutralize the hydrochloric acid formed in the ferric chloride bath)
The process:
Put on nitrile or latex gloves
Tie string to scale
Clean the scale in the dishwashing liquid
Rinse in the water
Clean with degreaser
Rinse in the water
Clean again with degreaser
Rinse again
Pat dry with lint-free cloth
Dip into ferric chloride/vinegar bath and leave for a few minutes
Remove scale from etch bath and drop into baking soda bath
RinseIf the black oxide finish is to your liking, then dry and soak in oil for a while.
If not, repeat the steps above.This method will achieve a dark grey, not black, finish. There are solutions (copper/selenium) for sale that can produce a black finish, but I don't know how durable they are. This method is relatively cheap and can be repeated if the finish is scratched or worn away.
-
Hey, thanks for the setailed HowTo Adam

I'll have to try that out. -
Will have to check this method out

-
Gotta admit that Adam was on to something with this mod.
I had considered picking up a Gerber Armbar, but after reading all the negative reviews, I decided against it and pulled out my Multiforce, instead.
My original intent was to use the 2 blades but couldn't because of the indent location so I went with the saw blade.
Got a little more work to do on the bit holder to get it into alignment with the handle, but it certainly isn't liable to fold up, like the Armbar.Also, went without the pocket clip, on this one. It's about the same size as my large Stockman, so I'll just drop it in.
So, a big thanks to Adam for the inspiration.

-

This is what I was hoping the Armbar would be.
-
I like the shape of the Gerber blade. If they ever get it together on the scissors and implement tension, I still may pick one up.
I've still got some tweaking to do on the MF, but I'm pleased as punch with how it came out.
-
Great job, PC 8) I still haven't taken mine apart but
the Armbar could have been this or more
I do love the Armbar blade and the hammer on the end but it just isn't what this mod or my Charge knife mod is
:D -

I used the saw blade to cut in a lot of recessed can lights this week because I like it better than my Klein drywall saw. However, that left the knife full of drywall dust and in a desperate need of cleaning.
Also, the scissors spring has been sifting a bit when using the scissors, causing an annoying click. I think that I left out a washer the last time I reassembled it
In addition to those things, the straight driver that resides between the scissors and can opener is of very little use. There is a straight driver on the reversible bit in the bit holder. When I first performed the mod I knew the driver was wasting space but I did not have a good idea of what to replace it with.For all of those reasons, I yet again disassembled the knife. I thoroughly cleaned it and then went to work on replacing the straight driver. There were three tools that came to mind that I could use: a prybar, an awl, and a chisel/gouge/scraper. Given it resides opposite of the bit holder in the handle in the middle slot, its replacement could be no more than 3/4" to 1" longer than the driver. That eliminated the pry bar. So, I chose to install an awl.
I have my old Suspension laying around doing nothing, so I decided to rob something from it to make an awl. Unfortunately, the area around the pivot is too narrow to cut in a notch for the Multiforce tool lock.

So, I started looking over my other MTs that I am willing to rob from at this time.

Nothing with enough length and rigidity to make a good awl.Then I spied a poorly formed chisel/reamer on a Husky plumber's MT. On to option #3, the chisel/gouge/scraper.
I sharpened the chisel cut on the end so that it would actually gouge out wood. I sharpened curved part of the tool so that it could actually remove burrs from PVC conduit. And I ground a chisel edge along the other edge of the tool. I forgot to take a close up pic of the tool, but it is visible in the picture above.
In addition, I gave the scales another ferric chloride bath. The previous treatment was holding up well, but since I had it disassembled I figured I might as well do it.
-
More I look at yours, more I like the color. I just don't have the chemicals and other things to do that.
When I took mine apart, and was putting it back together, I put the flathead in upside down, twice, before finally getting it back right. Old guy with big hands to start with, along with arthritis and weak eyes can only do so much.
After I got the leftover parts I wondered where all those washers actually came from. Three different sizes too, kinda like a jigsaw puzzle.
-
I am on the verge of not being able to see what I am doing also.
-
More ideas for me to use when I do take mine apart

-
Well folks, since it's almost impossible to find find another Multiforce, in store, I just ordered another one. Also picked me up a 12 piece, 3 inch, security bit set, at Tractor Supply, for $13.00.
My Amazon wish list is getting full of different Multitools too.
I keep looking at different tools to change, after my first attempt so I only hope that I hit the bottom of the rabbit hole softly. -
I used the saw blade to cut in a lot of recessed can lights this week because I like it better than my Klein drywall saw. However, that left the knife full of drywall dust and in a desperate need of cleaning.
Also, the scissors spring has been sifting a bit when using the scissors, causing an annoying click. I think that I left out a washer the last time I reassembled it
In addition to those things, the straight driver that resides between the scissors and can opener is of very little use. There is a straight driver on the reversible bit in the bit holder. When I first performed the mod I knew the driver was wasting space but I did not have a good idea of what to replace it with.For all of those reasons, I yet again disassembled the knife. I thoroughly cleaned it and then went to work on replacing the straight driver. There were three tools that came to mind that I could use: a prybar, an awl, and a chisel/gouge/scraper. Given it resides opposite of the bit holder in the handle in the middle slot, its replacement could be no more than 3/4" to 1" longer than the driver. That eliminated the pry bar. So, I chose to install an awl.
I have my old Suspension laying around doing nothing, so I decided to rob something from it to make an awl. Unfortunately, the area around the pivot is too narrow to cut in a notch for the Multiforce tool lock.

So, I started looking over my other MTs that I am willing to rob from at this time.

Nothing with enough length and rigidity to make a good awl.Then I spied a poorly formed chisel/reamer on a Husky plumber's MT. On to option #3, the chisel/gouge/scraper.
I sharpened the chisel cut on the end so that it would actually gouge out wood. I sharpened curved part of the tool so that it could actually remove burrs from PVC conduit. And I ground a chisel edge along the other edge of the tool. I forgot to take a close up pic of the tool, but it is visible in the picture above.
In addition, I gave the scales another ferric chloride bath. The previous treatment was holding up well, but since I had it disassembled I figured I might as well do it.
I was thinking about mine, last night. I had wanted to include the serrated blade instead of the saw, but the indent was on the wrong side. Then I thought that why can't I simply drill through the current indent creating a hole to actually act as an indent.
Now, I'm almost ready for our vacation to end so I can get back to my tools.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login