The Go BIG Challenge
-
[quote author=old Lefty link=topic=87587.msg2269489#msg2269489 date=1628323977]
Day 7:
Trying to visually diagnose reason for intermittent engine control light*

*also known as staring the engine without a clue :) :)

-
Nice to see awl the pliers getting used, one of my fav tools on a SAK.

Day 7
The Maxi and the Mini, red of course


-
Day 7 of 60:
Swiss Champ accompanied me on watering duties.

-
Day 07/60
SC helped measuring the length of the staples currently loaded. I'll need to get aome 14mm ones.
It also accompanied me on my bike tour.

-
Day 7/60
Needed to change an inner tube on my bike. Found the irksome flint chip that had caused the mischief and then used the pliers to nip up the valve core on the new tube before insertion. This should stop my screw on pump from locking onto it and taking the core with it at removal. Scissors then helped with puncture repair patch cutting.

-
@McStitchy said:
Day 07/60SC helped measuring the length of the staples currently loaded. I'll need to get aome 14mm ones.
It also accompanied me on my bike tour.That looks lovely riding McS

-
@Fast Bill said:
That looks lovely riding McS
Bill
90% of my tour is onroadsways that size.
Up and down the hills through the country side.
I gave up washing the bike every month... :DExcellent fix on your bike

-
Day 7 of 30
Used fish scaler to help open can of fosters, my fingernails where too short to get pull tap enough high so swisschamp to rescue

Only Tools Matters
-
:ahhh :ahhh Are we having fun yet? :D :ahhh
-
Day 07 / 60
That bit driver is a marvel!

-
Great uses today!

-
@McStitchy said:
Bill
90% of my tour is onroadsways that size.
Up and down the hills through the country side.
I gave up washing the bike every month... :DExcellent fix on your bike

Thanks McS you lucky you to be taking a tour. I have a few Lezyne pumps but they're past Masters at removing valve cores from Presta valves from Conti tubes.

-
@Fast Bill said:
Thanks McS you lucky you to be taking a tour. I have a few Lezyne pumps but they're past Masters at removing valve cores from Presta valves from Conti tubes.
I've never had a Lezyne pump, but did you try the SwissChamp's pliers?
Just wondering if they would work for it
Edit: Saw Rizzie's reply below. I see how that problem could happen. What about screwing them in with some Loctite applied?
-
@Fast Bill said:
Thanks McS you lucky you to be taking a tour. I have a few Lezyne pumps but they're past Masters at removing valve cores from Presta valves from Conti tubes.
Fast Bill - I know what you mean about the screw on fitting on Lezyne track pumps removing the cores from Presta valves! However, once I’ve nipped up the valves (using a Park Tools valve tool) the problem hasn’t happened again. In my experience, the Lezyne pump fitting which screws onto the valve is the best solution for getting tubs up to pressure (for me typically 160-220 psi depending on the tub) and the later pressure relief valve which I was able to fit to my older pump made unscrewing the connector so much easier…. For my other bikes and tubeless tyres I use a JoeBlow which is spot and simple to use, it just can’t go to the pressures I use on my tubs. Here’s a pick of the pressure relief valve (in gold - they didn’t have silver ones at the time) which is well worth getting if your pump doesn’t come with it fitted as standard which the I think the newer ones do.

-
8/60
No idea what you're talking about so I'll just have a good old Nestlé Crunch
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login