The Go BIG Challenge
-
Day 7 of 30
Used fish scaler to help open can of fosters, my fingernails where too short to get pull tap enough high so swisschamp to rescue

Only Tools Matters
-
:ahhh :ahhh Are we having fun yet? :D :ahhh
-
Day 07 / 60
That bit driver is a marvel!

-
Great uses today!

-
@McStitchy said:
Bill
90% of my tour is onroadsways that size.
Up and down the hills through the country side.
I gave up washing the bike every month... :DExcellent fix on your bike

Thanks McS you lucky you to be taking a tour. I have a few Lezyne pumps but they're past Masters at removing valve cores from Presta valves from Conti tubes.

-
@Fast Bill said:
Thanks McS you lucky you to be taking a tour. I have a few Lezyne pumps but they're past Masters at removing valve cores from Presta valves from Conti tubes.
I've never had a Lezyne pump, but did you try the SwissChamp's pliers?
Just wondering if they would work for it
Edit: Saw Rizzie's reply below. I see how that problem could happen. What about screwing them in with some Loctite applied?
-
@Fast Bill said:
Thanks McS you lucky you to be taking a tour. I have a few Lezyne pumps but they're past Masters at removing valve cores from Presta valves from Conti tubes.
Fast Bill - I know what you mean about the screw on fitting on Lezyne track pumps removing the cores from Presta valves! However, once I’ve nipped up the valves (using a Park Tools valve tool) the problem hasn’t happened again. In my experience, the Lezyne pump fitting which screws onto the valve is the best solution for getting tubs up to pressure (for me typically 160-220 psi depending on the tub) and the later pressure relief valve which I was able to fit to my older pump made unscrewing the connector so much easier…. For my other bikes and tubeless tyres I use a JoeBlow which is spot and simple to use, it just can’t go to the pressures I use on my tubs. Here’s a pick of the pressure relief valve (in gold - they didn’t have silver ones at the time) which is well worth getting if your pump doesn’t come with it fitted as standard which the I think the newer ones do.

-
8/60
No idea what you're talking about so I'll just have a good old Nestlé Crunch
-
Day 8:
I’m lighting with my Smith and my reputation burns all thru the west:

Sent from my iPhone using Tapatalk
-
Always great to see a revolver and speedloaders!

For Day 8, used the saw to cut up some kindling for a fire.

-
@McStitchy said:
I've never had a Lezyne pump, but did you try the SwissChamp's pliers?
Just wondering if they would work for it
Edit: Saw Rizzie's reply below. I see how that problem could happen. What about screwing them in with some Loctite applied?
Thanks McStitchy and Rizio. After I experienced this out on the road a couple of times (there’s nothing like watching a speeding valve core for getting your undivided attention as it heads for the verge!) I’ve nipped them tight with small pliers and the SwissChamp pliers worked fine for this yesterday. I have also used Loctite. But this is the Go BIG challenge isn’t it

-
@Rizio Il Ghiro said:
Fast Bill - I know what you mean about the screw on fitting on Lezyne track pumps removing the cores from Presta valves! However, once I’ve nipped up the valves (using a Park Tools valve tool) the problem hasn’t happened again. In my experience, the Lezyne pump fitting which screws onto the valve is the best solution for getting tubs up to pressure (for me typically 160-220 psi depending on the tub) and the later pressure relief valve which I was able to fit to my older pump made unscrewing the connector so much easier…. For my other bikes and tubeless tyres I use a JoeBlow which is spot and simple to use, it just can’t go to the pressures I use on my tubs. Here’s a pick of the pressure relief valve (in gold - they didn’t have silver ones at the time) which is well worth getting if your pump doesn’t come with it fitted as standard which the I think the newer ones do.Thanks Rizio. I don’t run on tubeless as you’ll have gathered and I have seen the relief valve though I’ve never bothered to get one for my Lezyne track pump. Typically I run about 110psi on Michelin Pro 4 Endurance folding clinchers but I have run on Vredestein all weather tyres which go up to 140psi and that’s why I got into Lezyne (plus the sleek engineering).
-
Enough bike talk. Day 8/60. Glamour shot today with a couple of books i picked up yesterday.

-
@Fast Bill said:
Thanks McStitchy and Rizio. After I experienced this out on the road a couple of times (there’s nothing like watching a speeding valve core for getting your undivided attention as it heads for the verge!) I’ve nipped them tight with small pliers and the SwissChamp pliers worked fine for this yesterday. I have also used Loctite. But this is the Go BIG challenge isn’t it

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login