kamakiri's Former Lurker / New Member Intro (long read)
-
Can the main blade be slightly reshaped to fit the liners?
Sent from my SM-G991U using Tapatalk
-
Yes, reducing the tip by sharpening or reproducing another millimeter+ or so would make it clear. I took a bit off the corner of the round of the tang to help a bit. But it’s hard to work the material that way in an assembled knife. Still hangs low.
-
@kamakiri said:
Yes, reducing the tip by sharpening or reproducing another millimeter+ or so would make it clear. I took a bit off the corner of the round of the tang to help a bit. But it’s hard to work the material that way in an assembled knife. Still hangs low.Thanks for checking. Was this due to the donor? Is it easier to start with a Spartan and add the magnifier than to remove a layer from an Explorer?
Sent from my SM-G991U using Tapatalk
-
@GrouchoM said:
Thanks for checking. Was this due to the donor? Is it easier to start with a Spartan and add the magnifier than to remove a layer from an Explorer?Sent from my SM-G991U using Tapatalk
Yeah the original problem was with the donor. Unfortunately, it wouldn’t be easier for me to start with the spartan. The spartan would end up with shorter pins and likely mismatching parts. I was just distracted/excited/pleased when I took the scales off that they matched my date estimate for the knife exactly. The front scale is dated ‘98 and the back one ‘99. I just failed to double check everything before cleaning or tear down.


-
There was a ding on the mag bezel that I reduced somewhat.

-
👍
Sent from my SM-G991U using Tapatalk
-

Buttoned up a few mods today, but this one took the most work. Changed a few things from what I planned earlier. Liner lock works great and with the 111mm frame it’ll be a whole lot safer.It’s a Trekker with the 100mm hawksbill swapped plus a hook.

-
84mm Scissors with a Hook?

Internal/design pics in the mod forum in hulk’s thread here:
/post/2296650Still need to finish the cosmetic trimming and polishing, but the mechanics are 100% done.
In a nutshell:
No trimmed blades, tip sits inside alox scale profile.
No added or externally visible joints in backspring or tools.
Don’t break the scissor spring!!! Not serviceable without taking the knife apart.
Snap is insane. Avoiding the original pivot hole limits how close the new round of the tang can be. And I left over 1mm of material. Could go thinner, but didn’t.
Hook sits ~0.5mm proud. Reducing or eliminating this is possible, but lots of work and I wanted to see what could be done without modifying the hook itself.


-
Pics from fit testing



-
Processing the recent arrivals…
Found this one that needed a 1-minute fix.
The cool thing about the knife is that it’s c.’81 and has a stainless advertising inlay and a rare-ish back shield in nickel silver.

-
Speaking of nickel silver.
This smurfy plastic had to go…

-
Both projects from above

-
Not much knife time today. Punched these out and prepped some other stuff for 2.2mm pins.

-
Just a test fit…
Serrated Bantam X
74mm scissors
4 knives used for donor parts.
-
Excellent work, Kamakiri!

-
Thanks guys!I still have to decide if I’m going to assemble this one as shown. Other options for this knife are to flip the orientation of the 74mm scissors or switch to 91mm ones with the hook, or do another spring for the no hook 91mm.
The small advantage of this orientation is that the exposed profile of the scissors completely fits within the profile of the main blade when closed. Bad part is that those two nail nicks are pretty close.
:-\ Decisions, decisions.
-
That looks great, Kamakiri!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


