Show off your Sak mod's!
-
Sweeeet!
-
I think I’m getting a Compact for Xmas, and the one thing I can’t stand is the corkscrew, yeah it gives you that little screwdriver but I’d soo like to put a Philips on it, heck even sneak a saw on it with a blank backside? But that means changing out all the pins rather then just the one if swapping out only corkscrew for the Philips,,
JR -
@Helvetica Bold said:
Sweeeet!
Thanks again, HB! Performing well yesterday after extensive sharpening efforts.

@MadPlumbarian said:
I think I’m getting a Compact for Xmas, and the one thing I can’t stand is the corkscrew, yeah it gives you that little screwdriver but I’d soo like to put a Philips on it, heck even sneak a saw on it with a blank backside? But that means changing out all the pins rather then just the one if swapping out only corkscrew for the Philips,,
JRI think I might do that with my ‘old’ Trail Guide that I used to demonstrate the scraper mod on its Combo Tool. Either regular Phillips, 58mm Combo phillips or ? Corkscrew isn’t so useful to me on more ‘urban’ knives.
Thinking of a blade swap for serrated too while I’d have it apart. New plus scales as the original Marlboro ones were already trashed when I got this one.

-
Thanks again, HB! Performing well yesterday after extensive sharpening efforts.

I think I might do that with my ‘old’ Trail Guide that I used to demonstrate the scraper mod on its Combo Tool. Either regular Phillips, 58mm Combo phillips or ? Corkscrew isn’t so useful to me on more ‘urban’ knives.
Thinking of a blade swap for serrated too while I’d have it apart. New plus scales as the original Marlboro ones were already trashed when I got this one.
Pretty much the same tool but with the added file, my thing would be to only have to pop that one pin in order to swap to the Philips, although In your case and just having to swap out the serrated blade you might be able to just do one other pin, unlike where I’d like to add a saw I’d have to do all of them..
JR -
@MadPlumbarian said:
Pretty much the same tool but with the added file, my thing would be to only have to pop that one pin in order to swap to the Philips, although In your case and just having to swap out the serrated blade you might be able to just do one other pin, unlike where I’d like to add a saw I’d have to do all of them..
JRThat’s true…one pins swaps are nice when that’s all you need. I have a habit of doing that to donors when I only need one part, like a serrated blade.
I also have it in my head to convert the whole thing (the Trail Guide) to 84mm just to try it. But I haven’t shortened the case hardened type metal saw yet. Stainless ones are easy enough.
-
@kamakiri said:
That’s true…one pins swaps are nice when that’s all you need. I have a habit of doing that to donors when I only need one part, like a serrated blade.I also have it in my head to convert the whole thing (the Trail Guide) to 84mm just to try it. But I haven’t shortened the case hardened type metal saw yet. Stainless ones are easy enough.
I have a few parts one being a backside Philips and a saw and I think I’m getting a compact for Xmas, so simple and easy, or pop them all and go all out

JR -
@MadPlumbarian said:
I have a few parts one being a backside Philips and a saw and I think I’m getting a compact for Xmas, so simple and easy, or pop them all and go all out
JR
Sounds good to me, and I’ll give you a nudge if that’s what you’re looking for.
:) ;) -
No idea what I was playing at here but I like it! It works for me as a 2 layer but I feel with either a mag layer or a pliers layer (either or, not both) would make this even better!



-
@Helvetica Bold said:
No idea what I was playing at here but I like it! It works for me as a 2 layer but I feel with either a mag layer or a pliers layer (either or, not both) would make this even better!
Nice. I do something similar, but with the spring 1 liner width more under the saw. I did it that way because of the higher spring pressure in the saw tang. Liners ‘hide’ the exposed sweep of the tang. -
nice Good idea Helvetica Bold
is it the spring of the big blade?
-
@Helvetica Bold said:
Thanks Hulk. Yep same same spring as if it were a blade just need a thin .2mm extra spacer to take the wiggle out as the saw is thinner than the blade ;o)I thought you didn’t crink the saw!


….
84mm Stainless Metal saw. No bushing required at the pivot. Still in test fitting and needs final trimming, but geometry looks good so far.

-
84mm metal saw is quite a rare beast isn’t it? That’s down the small blade end isn’t it? Mine replaces the main blade which may be the difference?
-
@Helvetica Bold said:
84mm metal saw is quite a rare beast isn’t it?Original case hardened w/o the nail nick ones are. But I haven’t seen any of the Stainless or case hardened 91mm ones shortened to fit 84mm yet.
That’s down the small blade end isn’t it? Mine replaces the main blade which may be the difference?
Yes, it is. Sorry, I wasn’t posting it as an example of a main blade knife replacement.
-
1/2 Cadet X (2 layer, no openers, w/hook)

-
Great minimal edc combo…you can open beer bottles with the hook anyway ;0)
-
Thanks HB…I was thinking about making bit a ‘big money clip’. But I think that should be on a riveted knife. Well, unless the clip is crewed in too. I was thinking the 74mm clip pinned into the back scale.
-
Cadet X
Modern bits, vintage details.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login